Search Documents

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By E. C. Truesdale, W. K. Waring

The Research,Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kids of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein' some years ago: ZnO + CO = Zn + CO2 [i] C + COj = 2CO [2] Each of these reactions is dependent upon the other for the supply of CO and COz, respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + He = Zn + HZO 13] C + Hz0 = CO + He U3 While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse Ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction is still the faster. He also says (p. 48), "At temperatures . . . be- -tween 1100' and 1300°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates.'' In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier's statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of ' a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented.*

Jan 1, 1944

By Walter S. Lutz, J. T. Griffith

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By J. T. Griffith, Walter S. Lutz

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

PAST AND PRESENT CHAIRMEN OF DIVISIONS Institute of Metals Iron and Steel Mineral Industry Industrial Minerals Year Division Petroleum Division Division Coal Division Education Division Division 1918 W. M. CORSET 1919 " 1920 W. H. BASSETT 1921 " 1922 W. B. PRICE RALPH ARNOLD 1923 E. DEGOLYER 1924 G. B. ELLIOTT 1925 F. JULIUS FOHS 1926 P. D. MERICA 1927 11 JOHN. M. LOVEJOY 1928 S. SKOWRONSKI A. W. AMBROSE RALPH H. SWEETSER ' 1929 " J. B. UMPLEHY G. B. WATERHOUSE 1930 ZAY JEFFRIES C. V. MILLIKAN W. J. MACKENZIE HOWARD N. EAVENSON 1931 SAM TOUR C. E. BEECHER F. M. BECKET 1932 C. H. MATHEWSON EARL OLIVER F. N. SPELLER THOMAS G. FEAR C. H. FULTON 1933 T. S. FULLER W. E. WRATHER JOHN JOHNSTON ELI T. CONNOR " 1934 J. L. CHRISTIE H. D. WILDE, JR. L. F. REINARTZ " T. T. READ 1935 W. M. PEIRCE HARRY H. POWER A. B. KINZEL JOHN T. RYAN SAMUEL H. DOLBEAR 1936 E. H. DIX, JR. HALLAN N. MARSH C. E. WILLIAMS EUGENE MCAULIFFE WILLIAM B. PLANK OLIVER BOWLES 1937 A. J. PHILLIPS M. ALBERTSON FRANCIS B. FOLEY J. B. MORROW " CHESTER A. FULTON 1938 R. F. MEHL G. B. CORLESS J. T. MACKENZIE PAUL WEIR FRANCIS A.THOMSON J. R. THOENEN 1939 R. H. LEACH W. H. GETS J. HUNTER NEAD C. A. GIBBONS " M. M. LEIGHTON 1940 E. M. Wise T. V. MOORE F. T. SISCO C. E. LA WALL W. R. CHEDSEY W. M. WEIGEL 1941 D. K. CRAMPTON E. A. STEPHENSON C. H. HERTY, JR. JULIAN E. TOBEY " PAUL M. TYLER 1942 CARL E. SWARTZ HARRY P. STOLZ E. C. SMITH NEWELL G. ALFORD A. F. GREAVES-WALKER B. L. MILLER

Jan 1, 1943

By W. F., Netzeband

SEVERAL criteria have been used more or less successfully in finding and developing orebodies in this district. Among them is the relation of the fracture to the orebodies. It has been known for some time that there was some relation, but it has been but recently. that careful study has been given to this subject. Like all the criteria used in this district, this relationship must be used with caution, for what-is true in one part of the district is not necessarily true in another.

Jan 1, 1928

By AIME AIME

LEADING off the Thursday morning session on Non-metallics was C. E. Heinrichs' paper, "Phosphate Flotation, Its Place in the Technology and Economics of the Phosphate Industry." Mr. Heinrichs also presented a closely related paper, "Milling Methods and Costs at the No. 2 Concentrator of the Phosphate Recovery Corporation," by H. S. Martin. The first of the papers points out the great significance of flotation to the phosphate industry, inasmuch as flotation practically doubles the potential recovery, thereby decreasing production costs and increasing reserves materially. The second paper describes three such plants, two of which are in Florida, the third being at Wales, Tenn. Operating characteristics and costs are reviewed. Answering inquiries from the floor, Mr. Heinrichs said that the adoption of a new parallel-shell dryer, from 60 to 80 ft. long, instead of the old single-shell countercurrent dryer, had increased the unit drying capacity over 300 per cent and had reduced the drying cost to less than 25c. per long ton of dried product. The initial moisture is from 15 to 18 per cent and the final about 2 per cent.

Jan 1, 1933

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By R. G. Treuting

Germanium single crystals strained in tension at 600°C slip on the {Ill} plane and, macroscopically at least, in the <110> direction. Deformation is in homogeneous: various localized rotations are observed, as is a banding consistent with secondary slip banding. The structure after deformation is polygonized with a domain size of about 2x1O-3 cm. In relaxation tests, an incubation period prior to flow is observed, of duration inversely related to temperature and applied stress. Under continuous loading, there is a sharp first yield point. A critical resolved shear stress therefore must be cited with respect both to temperature and to rate of loading. At 600°C, when loading proceeds at 2900 psi per min, it is 1310 psi. The yield point phenomenon is suggestive of Cottrell&apos;s solute atom atmosphere theory and five points of qualitative agreement with this theory are found. PLASTICITY of germanium at elevated temperatures has been reported by Gallagher,&apos; who ascribed it to slip on {Ill) planes and described some associated effects. Preliminary experiments with single crystals of silicon and germanium loaded as simple beams confirmed {ill) as the slip plane of both materials.V his was demonstrated by the standard technique employing traces on two surfaces of known angle on a deformed crystal of known orientation.3 These experiments did not fix the slip direction, since more than one glide system operated. Uniaxial tensile straining is preferred for this purpose in order to restrict slip to one predominant system and to provide an unequivocal determination of the orientation change with respect to the stress axis. Experimental Method Specimens were diamond-sawed from germanium crystals containing about 5x10-5 wt pct Sb prepared by the zone-leveling process described by Pfann and Olsen;4 these specimens measured about 81/2 in. long, 0.20 in. wide, and were of various thicknesses from 0.035 to 0.060 in. Prior to testing, a specimen was coated over 1 in. or more of length at each end with Apiezon wax, chemically polished (in a solution of 15 ml HF, 25 ml HNO,, 15 ml CH3COOH, and 3 to 4 drops Br2), and dewaxed in warm xylene. A brief re-etching after scribing through a complete wax coating with vernier dividers provided gage marks at 0.200 in. intervals on the polished surface. A specimen with grips soft soldered to the ends was passed through the furnace tube and the grips pinned to the tensile machine in series with a stress gage. The Schopper testing machine is best described by reference to the illustration on p. 107 of Schmid and Boas5 and is operated with the pendulum arm locked, fixing the upper head. Load is applied through the screw-driven lower head, manually or by reduced speed motor. The furnace is 21/2 in. long surrounding a 4x7/16 in. ID quartz tube and was positioned about the specimen to permit free motion. The inert or reducing atmosphere required was sufficiently provided by a flow of helium introduced at the center of the furnace tube, with the tube ends loosely plugged with asbestos paper. Surface corrosion was slight. The stress gage employs a Be-Cu strip with SR-4 units incorporated in a simple bridge network with provision for balancing and calibrating. The bridge output on loading is fed through a Leeds and North-rup dc amplifier to a Speedomax 10 mv recorder, and calibration is obtained by dead loading. Experiments of two types have been conducted. Most have been in relaxation at constant elongation. One stress-strain curve has been taken with the machine continuously driven. Following extension of a specimen, Laue X-ray photographs were taken to obtain the orientation change between deformed and undeformed regions, recorded on a single film by translating the specimen in a plane normal to the beam between exposures. Sequences of such multiple exposures were made on some specimens to include the entire orientation range on one film. Slip Direction To obtain a maximum orientation change with a single slip system, crystals of very closely <110> axial orientation were used. The classic determination of slip direction rests on establishing that direc-

Jan 1, 1956

By E. S. Machlin

THE function of this paper is to present certain results based on the fact that the strain energy arising from the solution of out-of-size solute atoms into the solid matrix is free energy and not internal energy, and that this strain energy is almost wholly shear strain energy as Zener1 pointed out. One natural consequence of this fact is an expression for the excess entropy of mixing due to the strain energy. Also, a derivation of the integral molar free energy of mixing partitioned to strain energy will be made using the model of Lawson2 and thermodynamics. This derivation has the advantage of showing in a simple way the assumptions involved in Lawson&apos;s treatment. The excess entropy of mixing partitioned to strain energy can be derived in two ways. The first way makes use of the fact that the strain energy is almost wholly in the form of shear strain energy. In this case, as Zener1 pointed out, the change in entropy due to the addition of shear strain energy is to a first approximation given by ?S/?? p,T = - ?lnµ/?T p,? Hence, the excess entropy of mixing partitioned to strain energy will be given by Sx ? = ?S/?? p,T Gx ? = - ?lnµ/?T p,? Gx ? where, Gx ? is the relative integral molar free en- ergy partitioned to strain energy; S is the entropy; is the shear strain energy; µ is the shear modulus; T is the absolute temperature; p is the pressure; and ? is the shear strain. Zener,1 as well as others, has pointed out that the shear strain energy stored in a compressible isotropic solid due to the insertion of an off-size incompres-sible sphere into a spherical hole in the solid, is approximately given by 2/3 µ/O (O°I - O)2 where a is the volume of spherical hole and no , is the volume of sphere. If we now consider the introduction of one mol of such spheres into an infinite volume of solid, then the relative partial molar free energy excess due to strain energy alone is GM ? = 2/3 µ/v (v ° 1 - v)2 where v is the molar volume of solvent and v°1, is the molar volume of pure solute type 1. Let us consider that these spheres are the two types of atoms in a binary solution, then there will be a similar relation for solute 2. The total relative integral molar free energy excess due to strain is then, to the approximations stated above GM ? = GM ? x1 + GM2 ? x2 = 2/3 µ/v [(v ° 1 - v)2 x1 + (v ° 1 - v)2 x2]. Lawson&apos;s relation for the strain energy can be de-

Jan 1, 1955

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne&apos;s statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By P. G. Shewmon, F. R. Winslow

An experimental method is describedfor Ihe determination of the derivative of the surface free energy (y,) with surface orientation using symmetric bicrystals. The method measures the equilibrium root-angle of grain boundary grooves for the same grain boundary on two different surfaces. In contrast to previous methods, the presence of annealing twins is not necessary. Results on silver at 900°C indicate that ??s/?3 is 0.014y, on the (loo), 0.075y, on the (111), and < 0.004?s on the (110). DURING an investigation of the kinetics of grain-boundary grooving on silver&apos; values of the derivative of the surface free energy ?s with respect to orientation were needed. Previous investigations of these so-called torque terms show that, for low-index planes in copper2 and nickel,&apos; a finite derivative exists even near the melting point. These two studies give the only previously published values of the torque on low-index metal surfaces. These investigators measured the equilibrium root angles, both greater than and less than 180 deg, along the lines where a twin boundary intersects a free surface. The technique described here is suitable for materials which do not have annealing twins, and enables the surface for study to be chosen instead of having to work in a direction normal to the twin trace on the surface. The purpose of this paper is to describe this new technique and to report the values found for the (111): (100), and (110) surfaces of silver. To check the technique proposed above, a series of 99.99 pct Ag bicrystals were used. These bicrystals were grown from the melt by a modified Bridge-man technique so that a low-index direction was parallel to the growth direction. Two orthogonal faces were studied on each bicrystal. One of these contained the low index or simple plane normal to

Jan 1, 1963

By R. D. Daniels, T. W. Wood

The tensile properties of columbium and Cb-H alloys containing up to 455 ppm H were studied as a function of temperature and strain rate. Hydrogen, introduced into columbium at elevated temperatures, using a thermal -equilibrium technique, embrittled columbium most severely at about —77°C. This elnbrittle ment occurred even at hydrogen concentrations of an order of 20 ppm. At higher temperatures, the hydrogen tolerance of columbium increased in relation to the increased solubility of hydrogen in tile metal. Below this temperature hydrogen tolerance, as determined by ductility and fracture stress, increased slightly. Strain rate had little effect on the tensile results for cross-head speeds over the range 0.002 to 2.0 in. per min. Strain aging during the tensile test appears to explain the ductility mininmum at —77°C. The apparent increase in hydrogen tolerance at lower temperatures is attributed to the low mobility of hyhogen. Experiments were performed in which samples were prestrained in tension at room temperature and tested to failure at —196°C. Results suggest that hydrogetz segregation to preformed crack nuclei can cause subsequent embrittlement even at temperatures where hydrogen mobility is too low to cause embrittlement in a normal tensile test. COLUMBIUM is an example of the class of bcc metals with ductile-brittle transition temperatures sensitive to the presence of interstitial atom contaminants. Hydrogen is one of these embrittling contaminants. The embrittling effect of hydrogen is less potent, perhaps, in columbium than in some of the other bcc refractory metals, but it is still a problem of both theoretical and practical interest. Unlike hydrogen in iron and steels, hydrogen in columbium is exothermically rather than endo-thermically occluded. The embrittlement process in exothermic systems has not been studied as extensively as that in endothermic systems, especially at hydrogen concentrations below the limit of solubility. The purpose of this investigation was to evaluate the embrittlement process in initially pure columbium as a function of hydrogen content, temperature, and strain rate. The Cb-H phase diagram, according to Albrecht et al.,1 is shown in Fig. 1. Columbium reacts exothermically with hydrogen producing a solid solution at concentrations of less than about 250 ppm (parts per million by weight) H at room temperature. At concentrations above the highly temperature-dependent solvus a second phase is formed. Like many similar hydrogen-metal systems,2 his system exhibits a miscibility gap with respect to hydrogen solution. Albrecht found the critical temperature of the miscibility gap to be about 140°C, the critical concentration to be 0.23 atom fraction hydrogen, and the critical pressure to be 0.01 mm Hg. Above 140°C there is a solid solution of increasing lattice constant extending across the phase diagram. Hydrogen concentrations of particular interest in this investigation were those below the limit of solubility in columbium. At hydrogen concentrations above the limit of solubility, columbium will contain the hydrogen-rich second phase and will be brittle under most testing conditions because the hydride generally precipitates as platelets with coincident matrix lattice strains.1&apos;3 At hydrogen concentrations below the limit of solubility, the tensile behavior of columbium is expected to be more sensitive to the interrelationships between hydrogen concentration and mobility and the testing variables such as temperature and strain rate. Literature references to the hydrogen embrittlement of metals, especially ferrous alloys and titanium alloys, are too voluminous to mention. It is only recently, however, that detailed studies of the hydrogen embrittlement of columbium have been undertaken. Wilcox et a1.4 studied the strain rate and temperature dependences of the low-temperature deformation behavior of fine-grained are-melted columbium (1 ppm H) and the effect of hydrogen content (1,9, and 30 ppm H) on the mechanical behavior of columbium at a series of temperatures for a single strain rate. A strain-aging peak was ob-served at about -50°C which was attributed to the presence of hydrogen in the metal. Eustice and carlson5 studied the effect of hydrogen on the ductility of V-Cb alloys at a series of temperatures over the range -196° to 25°C. Pure columbium was embrittled by 20 ppm H which produced a ductility transition at approximately -70°C. Ingram et al.6 studied the effect of oxygen and hydrogen on the tensile properties of columbium and tantalum. A minimum in the notched-to-unnotched tensile ratio of hydrogenated columbium was obtained at about -75°C, but because of the relatively large hydrogen content employed (200 and 390 ppm) the ductility

Jan 1, 1965

By D. J. Sellmyer

In order to orient single crystals by the back-reflection method it is necessary to know the angles between the various crystallographic planes. These angles have already been published for the hexagonal close-packed metals magnesium, zinc, and cadmium.&apos;

Jan 1, 1965

By William P. Blake

The literature of the occurrence of quicksilver-ore in the United States does not contain, so far as the writer is aware, any mention of the locality herein described. In the preliminary report * upon the resources of the transPecos region of Texas, von Streerwitz gives a long list of minerals observed as occurring there, but cinnabar is not mentioned. In the second report upon the same region † mention is made of the reported existence of cinnabarite in one of the mountain ranges north of the Sierra Carrizo and the Bofecillos, but the author adds: " In spite of my careful examination of the float, I have not yet found any traces of this metal (quicksilver) up to the present time." Prof. Dumble, also, in * Geol. Surv. of Texas, E. T. Dumble, 1889, p. 225 (first report). † Geol. Surv. of Texas, E. T. Dumble, 1890, p. 713 (second report)

Jan 1, 1896

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946