Search Documents

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By Claudio Gutiérrez

The action of quebracho in the selective flotation of fluorite and calcite has been studied. It has been found that the unavoidable ions produced by dissolution of these minerals can precipitate calcium oleate which profoundly influences the adsorption of oleate. The depressing action of quebracho is due, at least partly, to a decrease of the oleate adsorption. The depression of flourite flotation by quebracho in the presence of calcium is due to the fact that precipitated calcium oleate can become only physisorbed, its adsorption being strongly prevented by quebracho. It is concluded that adsorption experiments with flourite must be conducted with a flotation-size mineral, which has a lower dissolution rate than when finely ground.

Jan 1, 1980

By W. H. Eardley

It is increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh—that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. Flotation Products Received At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent, lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent, moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent, moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain nodules and balls of unroast,ed concentrates, sulfur elimination

Jan 1, 1928

By R. L. Fullman

Relationships are derived between average dimensions measured on a polished cross section and the spatial dimensions of particles dispersed as uniform cylinders. The equations are applicable to the measurement of rods or plates without the stipulation that they be extremely thin. QUANTITATIVE analysis of the elements of mi-crostructures has been limited by a lack of knowledge concerning the relationships between observations on plane surfaces and the spatial nature of the structure. This paper is an extension of previous efforts to establish equations suitable for the quantitative investigation of microstructures. The equations derived fill two gaps in the range of particle shapes for which measurements may be required, namely those shapes lying between extremely thin plates and equiaxed particles (approximately spherical), and those intermediate between equiaxed particles and extremely thin rods or needles. In a previous paper' equations were developed relating dimensions measured on a polished cross section to the average spatial dimensions of particles in the form of spheres, extremely thin plates, and extremely thin rods. For extremely thin rods the dimensions measured on a polished cross section were found to depend on the radius only, so that no information concerning the rod lengths or number of rods per unit volume could be obtained from observations on a cross section. In this paper equations are derived relating dimensions measured on a polished cross section to the spatial dimensions of particles in the form of identical cylinders. These equations may be used to evaluate the dimensions of rods, as well as the dimensions of plates, without the stipulation that the plates or rods be extremely thin. The impossibility of evaluating the length of extremely thin rods from planar measurements appears as an increase in the amount of data required for a given precision, as the length-radius ratio increases. Consider a sample containing particles of a phase in the form of cylinders of uniform radius T and height t. If the cylinders are randomly oriented, as in a sufficiently large sample of a fine grained poly-crystalline material, area and lineal analysis may be carried out with parallel cross-sectional planes and lineal traverses. If the cylinders are not randomly oriented, it is necessary to randomize the orientations of the cross-sectional planes and traverse lines. Let a unit cube be cut from the sample, and a cross-section plane be passed through the cube parallel to one of the cube faces. The number of particles N, cut by the cross-sectional plane per unit area is equal to the number of particles N, per unit volume times the probability p1 of a plane intersecting a single randomly positioned and randomly oriented cylinder in the cube. Let J be the maximum cylinder dimension in the direction normal to the cross-section planes, as shown in Fig. 1. Since, of the various possible positions for the cross-sectional plane over the unit length from top to bottom of the cube, only those positions existing over the length J

Jan 1, 1954

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

THE opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced. Mr. Franklin B. Gowen, who addressed the Institute as follows MR. PRESIDENT AND GENTLEMEN : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of gentlemen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a pro¬cess that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers, * A joint discussion of the subject of Technical Education, by the members of the American Society of Civil Engineers and the American Institute of Mining Engineers, was held in the hall of the Franklin Institute, on Monday evening, June 19th, and Tuesday morning, June 20th. This discussion has been printed in a separate pamphlet by both societies.

Jan 1, 1877

By William C. Grady

Microscopic pyrites are present in all West Virginia coals. Sizes of these pyrites range from 0.1 µ 500 µ (1/2 mm) , and four types are noted: massive, patches, framboids, and isolated crystals. The relative and absolute abundances of the four types vary from seam to seam, and these distributions have a marked effect on the ease with which a seam may be cleaned of pyritic sulfur.

Jan 1, 1978

By Keith E. Robinson, Brian Stimpson

INTRODUCTION In inclined sedimentary strata slope failure may occur by sliding along bedding and along a discontinuity or weak zone, as illustrated in Fig. 1. This mode of failure may be called 'bi-linear', as the failure surface is comprised of two linear or approximately linear segments. This type of failure has been suggested for the famous Frank Slide, Alberta, Canada (Cruder and Krahn, 1973) in which an estimated 90 M 5 tons (8.97 x 10 MN) of rock separated from Turtle Mountain and buried the town of Frank. Also, with the increasing depth of open pits and the construction of highways through inclined sedimentary strata this mode of failure is of major concern to the rock slope stability engineer. A computer program for calculating factors of safety for this slope failure mode is provided and includes the ability to vary shear strengths of potential slide surfaces, ground water elevations and wedge geometry. LIMITING EQUILIBRIUM MODEL The simple limiting equilibrium model used in the analysis is shown in Fig. 2. It is assumed that jointing is orthogonal to bed- ding and that the interface between the upper and lower wedges there- fore corresponds to a joint plane or planes. No shear strength is attributed to the interface so that the resultant force, P, from the upper wedge acts normally across the interface. The normal loads

Jan 1, 1983

By A. J. Jacobs, G. Katz

MANY of the studies of intermetallic compounds containing uranium were performed during the early 1940's under the aegis of the Manhattan Project. Subsequently, much of this work was declassified and published after 1949. In some instances this early work, completed with relatively impure materials, represents the only source of X-ray diffraction powder data available in the literature. In the case of the intermetallic compound U,Fe some discrepancies in the powder pattern exist in the literature. Since this compound has been prepared in this laboratory, it is believed that the publication of the indexed powder pattern would help clarify the conflict in the literature. In studies of the U-Fe system, Gordon and Kauf-mannl and Grogan and Clews2 independently reported the intermetallic compound U,Fe in 1950. The crystal structure was described by Baenziger, Rundle, Snow, and Wilson3 in 1950. It is isostructural with U,Mn, U,Ni, and U,Co and crystallizes in a body-centered tetragonal lattice. The lattice constants determined by Baenziger et al. are: giving an X-ray density = 17.7 g cm-3 for 4 mol per unit cell. The compound used in this study was prepared by melting a stoichiometric mixture of the constituent metals in an argon-arc furnace using a nonconsum-mable tungsten electrode. Before the argon of 99.98 pct purity was introduced into the furnace, it was passed through CaC1, to remove water vapor and afterwards through a stainless steel tube containing calcium turnings heated at 600°C for the removal of nitrogen and oxygen. The purity of the uranium used was better than 99.9 pct and that of the iron was 99.97 pct. Before and during melting a zirconium getter was used to further purify the argon atmos-

Jan 1, 1962

Both drilling and production of oil decreased in Rumania during 1935. The drilling totaled 1,042,041 ft. and production 61,973,938 bhl., being a decrease of 8.5 and 1.6 per cent, respectively. Wells completed during the year totaled 198, of which 168 were oil wells, compared with 238 and 215, respectively, of 1934. No important discovery was made during the year. The only new field found was Valea Calugareasca, where the Credit Minier completed a small well on the westward plunge of the anticline. Drilling higher on the structure will probably prove the field to be of greater importance than the results of the discovery well indicate. The only other developments of importance were the extension of the Bucsani field, the opening up of a new area on the northeast of the salt at Moreni by Credit Minier and a minor extension of the West Gura Ocnitei field. At Calinesti, on the cast extension of the Moreni field, exploration work continued and a gas well was completed, but oil in commercial quantities is yet to be found.

Jan 1, 1936

Both drilling and production of oil decreased in Rumania during 1935. The drilling totaled 1,042,041 ft. and production 61,973,938 bhl., being a decrease of 8.5 and 1.6 per cent, respectively. Wells completed during the year totaled 198, of which 168 were oil wells, compared with 238 and 215, respectively, of 1934. No important discovery was made during the year. The only new field found was Valea Calugareasca, where the Credit Minier completed a small well on the westward plunge of the anticline. Drilling higher on the structure will probably prove the field to be of greater importance than the results of the discovery well indicate. The only other developments of importance were the extension of the Bucsani field, the opening up of a new area on the northeast of the salt at Moreni by Credit Minier and a minor extension of the West Gura Ocnitei field. At Calinesti, on the cast extension of the Moreni field, exploration work continued and a gas well was completed, but oil in commercial quantities is yet to be found.

Jan 1, 1936

By F. P. Haver, M. M. Wong

When a mixture of chalcopyrite concentrate and lime is heated in air, the following reaction takes place: 2CuFeS2 + 4Ca (OH)2 + 8 ½ 02 ; 2Cu0 + Fe203 + 4CaS04 + 4H20. Ca (OH)2 is the only common reagent that will adequately control SO2 evolution in roasting. Other additives tried, including CaO, CaCO3, Na2CO3, NaOH, MgO, Mg (OH)2, and MgCO3, were not effective. All reacted with sulfur, but not to the extent that will be required to meet the new control regulations for sulfur oxide emissions. For example: when the concentrate was heated with the theoretical amount of limestone (CaCO3), about 55% of the sulfur was retained in the calcine; whereas use of the stoichiometric amount of Ca (OH), converted approximately 99% of the sulfur to CaSO1. In most of the experiments, Ca(OH)2 was formed by adding CaO to concentrates containing enough water to simulate filter cake from flotation circuit. This eliminated the need for drying the concentrate and utilized the heat of hydration of CaO.

Jan 6, 1972

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for OFHC copper, and for a series of binary solid solutions of high purity copper with zinc, gallium, germanium, arsenic, and silicon, to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity. The apparatus used was of the torsional pendulum type developed by KeI1 modified so that the specimen and vibrating system could be maintained in a high vacuum. The activation energy for grain boundary relaxation in copper is 33,000 cal per mol. This is considerably less than the activation energy for self-diffusion, in disagreement with Ke's theory2 that the two activation energies should be the same. All the alloying elements increase the activation energy for grain boundary relaxation to approximately 44,000 cal per mol, increasing the grain boundary viscosity at a given temperature. The results are discussed in terms of theories of grain boundary slip put forward by MottQ and by Ke.+ Experiments have also been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. EXPERIMENTS described in this paper were designed to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity, using the internal friction method developed by Kel for measuring grain boundary viscosity. It was considered desirable to make the system under investigation as simple as possible by making experiments on a comprehensive series of binary alloys of copper with the elements immediately following it in the periodic table, i.e., zinc, gallium, germanium, and arsenic. These elements are within the range of favorable size factor for solution in copper, and the systems have been extensively investigated by Hume-Rothery and his co-workers." Later, in order to study the effect of the relative size of the solvent and solute atoms, experiments were made on a series of Cu-Si alloys, since the apparent atomic diameter of silicon when in solution in copper—the diameter necessary to assign to the solute atoms to account for the lattice constant of the solid solutiona—is almost the same as that of the solvent atoms. Preliminary experiments were made to measure the variation of internal friction with temperature for pure copper. Ke made some experiments on copper," but found that the curves obtained were not reproducible in consecutive experiments. The copper was maintained in an argon atmosphere during the experiments but, although he took precautions to exclude oxygen, Ke came to the conclusion that the precautions were not entirely satisfactory, and that the lack of reproducibility must be due to absorption of oxygen by the copper. Experiments have therefore been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. Previous Work Ke made extensive experiments on high purity aluminum and was able to show that the grain boundaries behave viscously at high temperatures. He found that the relative rate of movement of the grains could be expressed as Where v is the velocity of slip, A is the constant, u is the shear stress, H is the activation energy, R is the gas constant, and T is the absolute temperature. By assuming that the boundary layer was one atom thick, he obtained a value for the viscosity which, when extrapolated to the melting point, gave good agreement with the viscosity of the liquid metal at the melting point. Ke also made experiments on other high purity and commercial purity metals:, and on some alloys." " He came to the conclusion2 that the activation energy for grain boundary slip was the same as for self or volume diffusion and for steady state creep in single crystals. Rotherham, Smith, and Greenough" have shown recently that the activation energy for grain boundary slip is not the same as for self-diffusion in tin,

Jan 1, 1957

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By Edward H. Robie

SUBJECT to formal Board approval in September, AIME dues will continue indefinitely at the present scale of $20 for Members and Associate Members; and $12 for Junior Members for the first six years of such membership, thereafter $17. That is the wish of the Board of Directors and the will of the membership, as expressed in the recent referendum. Though the official returns, as reported by the tellers, are not available as this is written, the data are sufficiently complete to give the results to the nearest percent. The total vote was approximately 93 pct for continuance of the present scale. Metals Branch members voted about 94 pet for continuance; Mining Branch members slightly less than that; and Petroleum Branch members about 91 pct. As in the referendum of 1949, there was no particular difference of opinion on the question of dues as between the three Branches. The percentage of ballots returned was about 61 pct, only slightly more than in the 1949 referendum. But the affirmative vote was much greater, 93 pct against 78 pet in the earlier referendum. Looked at another way, a majority of those to whom ballots were sent, 56 pct, voted to continue the present scale of dues, whereas only 46 1/2 pct of those canvassed voted to raise the dues in the previous referendum. But approximately 600 , members expressed their opinion that the dues should go back to $15 for Members and Associate Members and to $10 and $15 for Junior Members. This is a substantial group of members who either do not think they are getting their money's worth from AIME membership, or believe that a more businesslike conduct of Institute affairs should provide current services at less cost, or believe that more service is being provided for their dues than they need. As to the first point, it is probable that some members are not getting their money's worth. They perhaps have only a fringe interest in. AIME activities, or they do not or cannot participate in such activities at the Local Section, divisional, or national level, so that all they get out of the Institute is the monthly journal, which they do not have time to read. If they did read it intelligently, and acted upon the professional information thus gained, it is difficult to understand how one or more ideas cannot be gained that would be worth $20 to them professionally. But the 600 members who want lower dues offer a challenge to the Directors and to the staff to do a better job; to make Institute membership so rewarding that every. member will be thoroughly satisfied. Twenty 1935 to 1939 dollars are worth only $11.60 now, according to the latest government data, but that makes it all the more necessary for us all to appraise the value of what we buy. To the 93 pct of Institute members who expressed a vote of confidence, so to speak, the staff, and we feel sure the Directors as well, are most appreciative and thankful.

Jan 1, 1952

E. A. Peretti (University of Notre Dame, Notre Dame, Ind.)—Mr. Deitz and Professor Halpern are to be congratulated on a fine piece of work which adds to our knowledge of precious metal—cyanide-solution reactions. I should like to offer the following comments: The authors state, "the rate plots were always linear, indicating a zero order reaction rate." This appears to conflict with the data of Fig. 6 which clearly show the rate to vary with the NaCN concentration. It seems to me that the rate curves are linear because of the experimental setup. The volume of solution is so large that over a three-hour period the change in NaCN concentration is very small. A rough calculation for the experiments of Table I where the initial NaCN strength was 0.0096 mol per liter show a change of NaCN concentration of about 0.0009 mol per liter at the end of three hours. In short, over the period of time that the experiment was in progress, the NaCN strength was practically constant; hence the rate of dissolution remained practically constant. Eq. 10, as written, specifies that 1 mol of H202 and 2 mol of hydroxyl ion are formed when 2 mol of silver react. Is this true? The effect of H,O2 on the rate was made in solutions having an oxygen pressure of 4.8 atm. Were any tests made in solutions containing hydrogen peroxide, but no oxygen? G. M. Willis (University of Melbourne, Melbourne, Australia)—The authors have shown that, under their experimental conditions of high O2 concentrations, the rate of solution of silver in aqueous cyanide solutions is controlled by diffusion of O2 or CN- to the metal surface. With diffusion control, it is generally not possible to obtain further information about the mechanism of a process.

Jan 1, 1955

By D. L. Feucht, R. L. Longini

The semiconductor heterojunction is considered in terms of simple models which may lead to an understanding of move complex heterojunctions. Metallurgical and electrical properties of hetero-junctions aye discussed including the interface structure, energy -band diagram, and carrier transbovt across the interface. It is found that in a heterojunction all mechanisms such as injection, tunneling, and junction recombination found in simple junctions play modified voles. INTERFACES between materials (grain boundaries, the electrical junction between two differently doped materials in a single crystal, the oxide-metal interface, or metal-metal junctions) are of considerable importance in many situations. These various interfaces all have one very fundamental thing in common. Quantum mechanically speaking, the wave functions of the electrons in one material may penetrate the other material but, in general, only to the extent of angstroms. From an electrical point of view the conduction mechanism changes as a current passes through such junctions. In some cases the change is tremendous, in others almost negligible. The interface, then, is the locus of a change of conduction mechanisms. Some of these, particularly in semiconductors, are well-understood. The ordinary p-n junction in a single crystal can be the locus of an injection mechanism or a tunneling process, depending on conditions. The mechanisms are probably best understood in semiconductors because of the possible simplified view of particlelike conduction. The bands are either nearly filled or nearly empty and band overlap is seldom involved. The same fundamentals are probably important in other situations too but they are very difficult to look at naively. Although the simple look at the semiconductor case only gives us a relatively rough picture which must then be refined, the other systems, which involve a more complex situation, immediately are in many ways too difficult. There are too many initial choices of complex systems and therefore it is not possible to be even reasonably certain of any one model. Because of the relative simplicity of semiconductors, their good and controllable structure, and because of the ability to make many measurements on them not normally available to either metals or insulators! they are probably the best understood materials. It is therefore desirable to use them as a tool to further the understanding of interfaces in general. Semiconductor-heterojunction concepts were first proposed by kroemer1 in 1957. This was followed several years later by reports on the fabrication and experimental characteristics of heterojunction structures by Anderson2 and Diedrich and jotten.3 I) THE HETEROJUNCTION STRUCTURE To get down to hardware, when we refer to a semiconductor heterojunction we imply that there exists an intimate contact between different semiconductor materials. We could put two pieces of material together, complete with oxide layers, we could remove the oxides, or we could even melt the interface and hopefully get wetting and a good "bond" on solidifying. In fact we could by some means grow a crystal of one material using the other as a seed. Essentially we are interested only in the last two because they are the simplest to look at analytically. The degree of perfection of fit varies greatly and is reflected somewhat in the arc welder's joint strength. The lattice match of the two materials, their orientation, and so forth. is obviously necessary for a good bond but so is the continuity of any polar bonds which are involved such as in the III-V semiconductors. The mechanical misfit between two similar lattices can be described in terms of edge dislocations. The edge-type dislocations must be very close together for the usual misfit and there must be dislocations for each of several different Burger's vectors in order to produce a lattice match. The .'dangling bonds'' resulting will be involved in producing interface charge. Order of magnitude estimates of the charge density extrapolated from low densities of dislocations in homogeneous materials give 5 x 1013 cm-2 Ge-Si and 1 X 1012 cm-2 Ge-GaAs electronic charges. Edge dislocations also act as very active recombination centers between holes and electrons. One lattice "matching" difficulty usually exists even if two structures have essentially the same lattice constants as they will have different coefficients of therma1 expansion. Thus, on cooling from the usually high temperature of fabrication to room temperature, dislocations are produced, a good fit not existing at both temperatures. In brittle materials this shrinkage may even result in cracking. For the Ge-Si interface the mismatch is about 2 x 10 -6 per degree whereas it is less than 10"7 per degree between germanium and GaAs. The exact effect of the misfit is dependent on the thickness of the materials involved. For a very

Jan 1, 1965

By T. S. Hutchinson, C. E. Kemp

The bottom water drive analysis presented by Muskat has been extended to include fields with wider well spacings. Curves are presented from which volumetric sweepout, water-oil ratio, and rate relations may be calculated. The effects of non-unity ratios on sweepout eficiency and productivity decline have been studied by an approximate method. Also, the effect of gravity on volumetric sweepout has been approximated for a particurlar geometry. INTRODUCTION The purpose of this paper is to report work done in applying the analysis of bottom water drive reservoirs given by Muskat1 to a larger class of reservoirs, to extend this analysis to include the effects of gravity and non-unity mobility ratios in an approximate manner, and to investigate the rate of decline of productive capacity. The bottom water drive type reservoir is one where the oil is underlain by a water zone of sufficient thickness that water movement is essentially vertical. This system is defined in more detail in the appendix and a one well element is shown diagrammatically in Fig. 1. Muskat obtained solutions to the equations describing the volumetric displacement efficiency of idealized bottom water drive systems by assuming that gravity effects due to differences in density betwecn oil and water were negligible and that the mobilities of oil and water were the same. If either of these assumptions is not made, the complexity of the system makes an analytical solution well nigh impossible at the present stage of mathematical development. Coles and Stade' developed an approximation to consider these factors. The authors have refined approximations, starting with the same basic assumption, which should give a somewhat quantitative picture of bottom water drive performance when mobilities are not equal and the effects of gravity are not negligible. The results of these approximate calculations can then be used to obtain the decline in well productivity as the field is depleted.

Jan 1, 1957