Search Documents

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.' Thus in accord with Seeger's theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann's constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By Donald Cummings

CERTAIN dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is. approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribu-tion, except that the upper limit of size retained in the air sacs is approxi-mately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been gen-erally conceded, however, that particles of harmful dusts smaller than ¼ to ½ micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are, not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to dis-regard them.

Jan 1, 1935

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various Winds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By F. A. Olson, J. S. Cho, M. E. Wadworth

An infrared study of the states of hydration of MgSO4 revealed a hitherto unreported metustable dehydration state in the temperature range just below that of the stable anhydrous salt. Infrared, thermogvavimetric, and X-ray studies indicated that the state had bisulfate and hydroxide characteristics. A formula fitting all of the experimental evidence is hydrogen-bonded Mg(OH)HSO4, or possibly the chemically equivalent 1/2 Mg(HSO4)2. Mg(OH)2 Infrared spectra of the 7, 6, 1, and OH2O states of hydration are given as well as the spectra of the newly found state which is called the bisulfate state in this paper. Thermogvavimetric studies as a function of water-vapor pressure gave an enthalpy value of 16 cal per mole, and 25 eu for the conversion of the bisulfate state to that of the anhydrous salt. The free energies of the transition varied from 1.76 to 0.18 kcal per mole as the transition temperature varied from 279° to 336°C. The bisulfate state is believed to be of importance in catalytic dehydration phenomena using MgSO4 and may be of interest because of properties in sulfating reactions differing from those of the monohydrate. Also, an analogous state may exist as a hydration state of other sulfates. ANHYDROUS magnesium sulfate is a catalyst with a high degree of specificity for the dehydration of secondary alcohols.1'2 The only product obtained at the usual operating temperature range of 360" to 400°C other than the corresponding olefin is water. Thus, the bonding of water to the anhydrous salt as well as an understanding of the hydration states of MgSO4 became of interest in attempting to understand the catalytic mechanism better. In the process of this study using infrared, X-ray, and thermogravimetric analyses a dehydration state not previously reported was found. Proof of its existence, the nature of the state, and its role, if any, in the catalytic mechanism then became of interest. This paper is concerned principally with the first two aspects of this problem. Magnesium sulfate forms many hydrates, of which the monohydrate and heptahydrate (Epsom salts)3 are most important. Other hydrates4 are known with 1-1/4,5 l-1/2, 5 2, 4, 5, 6, and 12 H2O's. The hydrates with 1-1/4, 1-1/2, 2, 4, and 5 HzO's are unstable. The anhydrous salt is very stable thermally and has a strong affinity for water. It can be heated without additional decomposition to about 800°C.' At 900°C noticeable decomposition takes

Jan 1, 1964

By R. B. Ladoo, C. A. Stokes, R. N. Secord, A. L. Hall

INDUSTRIAL mineral history shows that the entrance of new, nonmetallic minerals into commercial production can be expected to occur from time to time. Latest entrant into the field is wollastonite. Except for one short-lived period in Kern County, Calif., starting in 1933, wollastonite has never before been produced on a commercial scale. But the signs are up for its entrance as an economic factor in the mineral market. Small scale experimental production from a deposit near Willsboro, N. Y., started about 1943. A pilot plant was built in 1949-50 and irregular, small scale, production has continued. In early 1951 Godfrey L. Cabot, Inc. of Boston, world's largest producer of carbon black, took an operational lease on the property to study the deposits and make market surveys. This became Cabot's first venture in the mineral field, when they took over operations and began design of a new mill, expected in production in 1953. Properties The properties and major uses of wollastonite are comparable to New York fibrous talc. It has about the same specific gravity and index of refraction as talc, but is somewhat whiter and softer. The two most important fields of use, paint and ceramics, are the same as for talc. Ground wollastonite has a fiber length as much as 13 to 15 times the diameter. This particular property makes it applicable in the paint field and others. In addition, the length-diameter ratio may be controlled to rather narrow limits by choice of grinding method. Another important commercial property is brightness or whiteness. Wollastonite reads from 92 to 96 pct of MgO on the G.E. brightness meter for a 99 pct -325 mesh grind. Purity and uniformity of product are important. Chemically, the wollastonite now being mined analyzes SiO2 51.76, CaO 47.56, FeO 0.46, MnO 0.04, and H2O 0.09 pct. Theoretically pure wollastonite analyzes SiO2 51.75 and CaO 48.25 pct. This analysis indicates over 98 pct calcium silicate, with only small amounts of contaminating ingredients. That these ingredients are not detrimental to color or brightness is shown by the high brightness value of the fine ground material. [ ] By-product calcium silicate from electric furnace production of phosphoric acid has little physical re-semblance. to this wollastonite, being an off color white, and lacking in fibrous crystalline character. Minerology Wollastonite is a calcium metasilicate, CaSiO3, a white, medium hard, fibrous mineral. In this deposit wollastonite occurs as well crystallized aggregates of bladed crystals intergrown with garnet, and with a few percent of green diopside. The beneficiated product is about 75 pct wollastonite, 15 pct garnet, and 10 pct waste, largely middling. Wollastonite-garnet ore occurs in at least two beds. The main bed, varying in true thickness from 30 to 70 ft, dips into the hill at an average 30° and is enclosed in gneisses. Diamond drilling has proven the orebody to an average depth of 200 ft along 2000 ft of outcrop with adequate tonnage for many years of quarry operation. The wollastonite-garnet ratio varies locally, but average composition is uniform over long distances. A friable ore, it is easy to drill, shoot, and crush. Beneficiation Unlike talc this ore has to be beneficiated. Successful treatment depends upon the fact that it contains virtually nothing but wollastonite, garnet and a minor percentage of diopside. A very pure wollastonite product can be made by high intensity magnetic and/or gravity separation methods.

Jan 1, 1952

By C. N. Kravig

STANDARD raises at Homestake are 150 ft long. Raises of more than 150 ft, driven with the use of a cage and hoist, are considered long raises- some have been driven more than 900 ft. Long raises have eliminated the need for access drifts on each level when transfer and ventilation raises are driven. These timbered cage raises, 7x9 ft in cross section, include a rock compartment and a combination cage, pipe, and manway compartment. To prevent excessive weight on the timbers, 10x10-in. bearing beams are cemented into hitches cut in the rock at 150-ft intervals. The beams also hold back timber movement caused by daily drawing of rock through the rock compartment.

Jan 6, 1957

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1'700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By Joseph Hartshorne

This plant is situated in the borough of Pottstown, on the banks of the Schuylkill river, between the Philadelphia and Reading Railroad and the Schuylkill Division of the Pennsylvania Railroad, on a plot of about 125 acres, most of which is reserved for future extensions. About 45 acres are to be used for houses, 40 of which have already been built. The accompanying plan will give a clear idea of the general arrangement of the works. Beginning at the lower or eastern end, the first building is the basic-cinder grinding-plant. At present, it consists of a 2000 mm. Jenisch ball-mill (Kugelfallmühle) similar to those used so extensively for grinding basic cinder in Europe. It was built by Herman LÖhnert, of Bromberg. The mill is very simple in design, and efficient in execution. About 13 horse-power is required to run it, and the average output is 20,000 pounds in 10 hours. The best work we have done is 29,000 pounds in 10 hours, with perfectly dry cinder. From 95 to 98 per cent. of the product will pass through a sieve with 100 meshes to the inch, while from 70 to 75 per cent. will pass through a 150-mesh sieve. The mill has been in service since last March, part of the time on double-turn, and the renewals and repairs have been very slight. The product of the plant is sold as a fertilizer. It runs from 18 to 24 per cent. in phosphoric acid, about 14 of which is reverted. The merits of this fertilizer were explained by Mr. W. H. Morris, at the Baltimore meeting of February, 1892 (Trans., xxi., 232), and by Mr. W. B. Phillips, at the Birmingham meeting of 1888 (Trans., xvii., 84). The results obtained by its use in Europe, where over 600,000 tons were used last year, are well known. Near the cinder-grinding plant will be situated the new machineshop, which is now being erected. The next buildings contain the brick-making plant and ovens.

Jan 1, 1893

By R. E. Shinkosk

This paper outlines the development of a program for increasing the life of woolen bags used for filtering Dwight-Lloyd gases by treating the bags and gases with hydrated lime. Methods and apparatus are described for determining alkalinity of dusts, acidity and breaking strength of bag cloth. Procedure and results, based on several years of operation, are presented. DURING 1939, additional facilities were constructed in the Dwight-Lloyd Blast Furnace and Baghouse departments at the Selby, California, Plant of the American Smelting and Refining Co. In order to handle adequately the increased volume of gases from the resultant increase in production, it was necessary to increase gradually the amount of water used for cooling gases ahead of the sinter machine baghouse. As a result of this increased water cooling, the average bag life dropped from 27 months in 1939 to 14 months in 1941. (Table I). This drop in life meant an increased. bag cost, as well as lower recovery of dust and some curtailment of operation. During 1941, it was found new bags showed as high as 0.3 pct acidity* after two weeks of opera- tion and as much as 2.0 pct acidity after some months of operation. This high acidity was present in spite of the fact that free oxide or relative alkalinity of the unburned dust ran from 5 to 6 pct. In view of these circumstances, a twofold program was started in Nov. 1941.t Part one of this program consisted of vigorously dipping all new bags in a weak lime solution, containing 50 lb of hydrated lime per 50 gal of water. Part two consisted of feeding fine, dry, hydrated lime into the gas stream intake of the sinter baghouse fan. Apparatus for feeding this lime is shown in fig. 1. All baghouse chambers are shaken in rotation about once each hour. On alternate hours, the baghouse operator places 50 lb of hydrated lime (one sack) into the lime feeder, starts feeder and immediately starts the bag shaking machinery. The rate at which lime is fed is set to coincide with the approximate time necessary to shake all sinter bag-house chambers, or about 15 min. It is felt this method of lime addition is most effective for getting lime into the woolen bag fabric. The amount of lime so fed averages about 600 lb per day. The amount of lime fed per day is varied to keep a minimum relative alkalinity of 9 pct in the unburned sinter dust. A daily dust sample is taken for alkalinity by allowing dust to accumulate in a sample pipe over a 24-hr period. This sample pipe, placed in any chamber cellar, is 2 in. in diam, 4 ft long, is sealed on the inner end, and capped on the outer end. It has a 1/2 in. slot cut for 18 in. along the tip end. This slot faces upward and allows the pipe to fill gradually with dust as bags are shaken. Breaking strength of bags has, in most cases, been the deciding factor in bag replacement. Bags that normally test 100 psi breaking strength when new are replaced when they test under 35 lb. The method for determining breaking strength is shown in the description accompanying fig. 2. Since the start of the liming program in 1941, bag life has increased from 14 months to an average of over 23 months, with a consequent material decrease in bag cost per year. Acidity, as per cent sulphuric acid, may be determined by means of a Beckman pH meter as follows: From a piece of bag cloth. which has been thoroughly cleaned of dust, a 5 g sample is weighed on a balance. Cut the sample into fine pieces and place in a 400 cc beaker. Add 100 cc (measured) of distilled water and stir vigorously. Filter on suction funnel, holding cloth pulp in beaker with a stirring rod. Wash cloth sample and filter wash water four additional times, each time with 20 cc distilled water, the last time squeezing cloth pulp over funnel. Discard pulp and rinse funnel and filter paper. Pour wash solution jnto measuring graduate and make up to exactly 300 cc with distilled water. Place into clean 600 cc beaker and measure the pH on meter. The per cent acid in bag cloth is read from the following table:—

Jan 1, 1951

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed. CRUSHED stone classified as limestone comprises about 70 pct of the crushed concrete aggregate and roadstone produced in this country, and the product has amounted in the recent past to about 97 million tons per year, valued at more than $123,-000,000.' Therefore an evaluation of the properties of rocks classified in these statistics as limestones and an ability to predict their behavior as aggregate in portland cement concrete are matters of considerable economic consequence to producers and consumers of aggregate. This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. It also points out certain results of the properties of these rocks on their performance as concrete aggregates. The problems encountered in efforts to explain the behavior of limestones, dolomites, and related rocks as concrete aggregate lie on the frontiers between the ignorance of the geologists and the ignorance of the engineers. The mineral composition and textures of the rocks have not been adequately explored and described, and the effects of mineral composition and texture on the performance of aggregates have been worked out in only a few cases. There are instances of unsatisfactory performance and some generalizations of those experiences. There are many more examples of satisfactory performance than of unsatisfactory, but there is practically no published information as to why a particular aggregate was satisfactory in a specific use. There are all too few investigations of undeteriorated concrete; more is known about the pathology of concrete than about its normal structure and aspect. As part of the investigation of aggregates, the classification of rocks is not an end in itself, but is a step toward recognition of properties expected to influence the behavior of aggregates in their intended use. Rock of any type may perform well or poorly as concrete aggregate, depending on the physical condition of the rock, its physical and chemical properties as compared to those of the matrix in which it is placed, and the circumstances under which the concrete is exposed. Some classification and descrip- tion of the limestones is necessary to distinguish subgroups whose members will probably behave in similar ways and to evaluate the group as a whole. The group name, limestone, includes and tends to conceal the identity of rocks that have a very great range in chemical and mineralogical composition, structure and texture, conditions of deposition, subsequent history, and suitability for use as concrete aggregate. All the rocks classified as limestones include one or both of the most abundant rock-form-ing carbonate minerals, calcite and dolomite, as major constituents. Carbonate rocks is a more descriptive and more accurate group name than limestone, which has generally been used to include dol-omitic or magnesian limestones and dolomites as well as calcitic limestones. Classification and Description of the Carbonate Rocks The question of names to be applied to the carbonate rocks may appear academic, but it is of practical importance as long as there are specifications for aggregate that result in acceptance or rejection of rocks by name and as long as failure to make distinctions among the carbonate rocks leads to misunderstandings of their properties and of what may be expected of them in performance. Materials included in production statistics as limestone and tested for concrete aggregate as limestone range in fact from calcareous shale and calcareous or dolomitic sandstone and argillaceous limestone and dolomite to calcitic limestone and pure dolomite and to rocks close to calcitic and dolomitic marble. To take a simple example: consider two manufactured coarse aggregates, both dense and unweathered, one composed principally of crystalline calcite and the other of crystalline dolomite, but both known as limestone. If each is used as coarse aggregate in a standardized concrete mixture with the same fine aggregate used in both cases, made into concrete specimens, and tested in accelerated freezing-and-thaw-ing, the test results will probably be quite different, because of the differences in internal bond and thermal properties between the two aggregates. As long as both aggregates are called limestone, the test results cannot be explained, or used except in a very limited way; if the aggregates are distinguished as limestone and dolomite and the consequent differences in texture and thermal properties are recognized, the results are reasonable. Classification of the carbonate rocks used as aggregate should be based on structure and on composi-

Jan 1, 1954

By Evan Just

Throughout history mining operations have, been relatively technical in character and somewhat esoteric. In ancient times mines were places where prisoners of war or criminals were sent, to drag out short lives of hard labor, under conditions ranging from hazardous to lethal. Underground mines were damp and poorly lighted, and workers were often cramped in narrow spaces and tiresome positions. Hard rock was mined by building fires against faces and quenching with water. Combustion products from these fires and from such dim torches as were provided, plus the dampness, made the underground atmospheres quite injurious to health. During the Middle Ages, mining became less penitential and more technical. Because of the desire of sovereigns to foster production from mines, miners enjoyed special privileges as free men. Crude pumping, hoisting, and ventilation systems were introduced (Fig. 9.1). However, mining remained a relatively hardworking, hazardous occupation, separated from the lives and comprehensions of most people. With the Industrial Revolution, steam-powered pumps enabled penetration to greater depths, and the use of power-driven machinery gradually revolutionized productivity. Skill became more important than back-breaking labor. This revolution continues into the present. Mining today uses some of the largest and most complicated machinery in existence and little rock is moved by direct labor. Power drills, explosives, and boring machines penetrate and break hard rock. The modern mine, surface or underground, presents an impressive panoply of drilling, breaking, loading, and transporting equipment, facilities for power transmission, pumping, and ventilation, and expensive, complicated crushing and treatment machinery. Modern technology, machinery, and skilled workmen produce an efficiency that knows no parallel in the raw material field. Mineral substances are extracted and converted into useful forms at costs which are dwarfed by those of providing forest or agricultural products in terms of comparable weights, even though conversion of these last categories is typically much simpler. Capital investment per worker, i.e., mechanization, is greater than in nearly all other industries. Despite these features, and more than average financial risk, the mineral industries perform at modest profit. The popular concept that mines and oil fields are sources of boundless rewards is a myth, sustained by the occasional unusual episode. Before one can start actual production of minerals, he must first acquire a suitable deposit. The process of acquisition will require anything from a rather simple search to a difficult, lengthy, expensive exploration effort. After locating the desired deposit, title must be obtained by denouncement, concession, leasing, or purchase. If the deposit is solid, it can be mined in pits or underground workings. If fluid or easily fusible, it can be produced through wells. If dissolved in lake or seawater, it can be

Jan 1, 1976

By Lawrence H. Van Vlack

The energy of the y-iron grain boundary was determined to be 850 ergs per cm2 at 1105°C. The a/a and the a/y boundaries possess somewhat less energy. The microstructures of several iron alloys are discussed in terms of the interfacial energy relationships. THE dependence of the shape of liquid interfaces upon their energies has been studied for some time.1"3 Recently, Smith' concluded that many of the microstructures observed in metals may be attributed to the energies of the interfaces between the grains and phases. While the energies of liquid surfaces have been measured by numerous different methods: only two attempts have been made to determine experimentally the energy of surfaces involving crystalline solids. Udin, Shaler, and Wulff8 used a procedure introduced by Berggren7 to measure the surface tension of solid copper. It consisted of determining the load required on a thin copper wire so that the surface tension was counteracted, and no net strain resulted. Bailey and Watkins8 sed a different technique and were able to determine both the surface tension of copper and the tension of the copper grain boundary. They measured the contact angle which liquid lead makes against a copper surface. They then calculated the above energies from the surface energy of liquid lead by using the Pb vs. Cu/CuY dihedral angle and the surface groove angle formed during thermal etching. They obtained a value of 1800 dynes per cm for the surface tension of clean copper and approximately 640 dynes per cm for the tension of copper grain boundaries. The former value was somewhat higher than Udin's value of 1500 dynes per cm. This paper includes a determination of the energy of the y-iron grain boundary. In addition, the micro-structural relationships of several other metallic and nonmetallic phases with iron were examined and an attempt was made to interpret the observed structures in terms of interfacial energy relationships. Theoretical Considerations In a three-phase material containing a solid and two liquids, there may be two solid/liquid interfaces, one liquid/liquid interface and one inter- granular interface. Liquid/liquid interfacial energies can be measured directly. Therefore, by determining the energy of such an interface and by measuring the required interfacial angles: the energies of the interfaces involving solids may be obtained.10 They may be shown schematically as in Fig. 1. The above procedure requires the following assumptions: 1—The interfacial energies are, in general, unaffected by boundary orientation, and 2— the shapes of the interfaces are unaltered between annealing and sectioning for microscopic examination. The first assumption is good to a first approximation as shown by Dunn and Lionetti11 except for a few critically orientated boundaries. Two conditions may alter the shape of a boundary upon cooling: 1—Precipitation of dissolved material upon one side of the interface, and 2—a change in volume during the transition from one phase modification to another. The former must be detected by microscopic observation. The latter may become appreciable in systems containing an interface between two liquids which solidify after annealing. However, possible movement of the two-liquid interface may be checked in the system diagrammed in Fig. 1 by measuring 8, for example, and comparing it with its value as calculated from the other interfacial angles by: tan8, C11 05 COS- o- + cos 8, cos- The choice of a suitable pair of liquids is limited by several factors. The relative values of the several

Jan 1, 1952

By K. M. Fagin, D. W. Carter

Six new oil fields were discovered in the East and East Central Texas district during 1942. The Coke and Quitman fields, in Wood County, at this time appear to be the two most important oil discoveries for the year. The. four other oil fields discovered were Concord, in Anderson County; Kildare, in Cass County; Weiland (ClubLake), in Hunt County; and Larissa, in Cherokee County. The Rodessa lime in the Chapel Hill field, Smith County, provided the only new oil zone in older fields. The Hawkins field, Wood County, was the most active in drilling operations, 125 new wells being completed during the year. The Chapel Hill field tied the Coke field for second place with 30 completions each. The third most active field was Kildare, with 10 completions. Like the other oil-producing districts of the country, wartime restrictions reduced the number of oil and gas-well completions to 265 in 1942, compared with 964 completions in 1941. This represents a drop of 72 per cent and only a little more than one half enough to replace the 437 producing wells abandoned in the district during the year. Tn addition, the number of producing wells temporarily shut down nearly tripled, far two principal reasons: (I) the rule of the Petroleum Administration for War preventing operators from equipping more than, one well on each 10 surface acres with pumping or artificial-lift equipment, and (2) the Railroad Commission's issuance of various orders permitting the transfer of allowable for wells having high water-oil ratios and high gas-oil ratios to other wells capable of producing the same with less waste of reservoir energy. No changes were made in prices of crude oil in the district during 1942. Production and Probation The district produced 158,928,281 bbl. of oil and distillate during 1942, compared with 163,566,695 bbl. during 1941, which represents a decrease of 3 per cent. The East Texas field produced 120,680,595 bbl. of oil, compared with 130,377,793 during 1941; a reduction of 9,697,198 bbl., or 7.4 per cent. The production of this field represents 75.9 per cent of the district total, compared with the 79.7 per cent that it furnished in 1941. The district had an estimated basic daily oil allowable of 623,242 bbl. on Dec. 31, 1942. Approximately 31.8 per cent of the production in Texas during 1942 was supplied by this district, compared with 33 per cent during 1941- Changes in the annual production of newer and flush fields in this district are attributable either to a difference in the number of wells producing during the year or to changes in basic allowable and number of shutdown days due to shifting market dconditions brought on by the war. All regularly prorated fields in the district were shut down 123 days. Major exceptions were the East Texas field, closed128 days; Hawkiis, shut down 106 days; and Cayuga, Sulphur Bluff, Talco, and Rodessa, which

Jan 1, 1943

By D. W. Carter, K. M. Fagin

Six new oil fields were discovered in the East and East Central Texas district during 1942. The Coke and Quitman fields, in Wood County, at this time appear to be the two most important oil discoveries for the year. The. four other oil fields discovered were Concord, in Anderson County; Kildare, in Cass County; Weiland (ClubLake), in Hunt County; and Larissa, in Cherokee County. The Rodessa lime in the Chapel Hill field, Smith County, provided the only new oil zone in older fields. The Hawkins field, Wood County, was the most active in drilling operations, 125 new wells being completed during the year. The Chapel Hill field tied the Coke field for second place with 30 completions each. The third most active field was Kildare, with 10 completions. Like the other oil-producing districts of the country, wartime restrictions reduced the number of oil and gas-well completions to 265 in 1942, compared with 964 completions in 1941. This represents a drop of 72 per cent and only a little more than one half enough to replace the 437 producing wells abandoned in the district during the year. Tn addition, the number of producing wells temporarily shut down nearly tripled, far two principal reasons: (I) the rule of the Petroleum Administration for War preventing operators from equipping more than, one well on each 10 surface acres with pumping or artificial-lift equipment, and (2) the Railroad Commission's issuance of various orders permitting the transfer of allowable for wells having high water-oil ratios and high gas-oil ratios to other wells capable of producing the same with less waste of reservoir energy. No changes were made in prices of crude oil in the district during 1942. Production and Probation The district produced 158,928,281 bbl. of oil and distillate during 1942, compared with 163,566,695 bbl. during 1941, which represents a decrease of 3 per cent. The East Texas field produced 120,680,595 bbl. of oil, compared with 130,377,793 during 1941; a reduction of 9,697,198 bbl., or 7.4 per cent. The production of this field represents 75.9 per cent of the district total, compared with the 79.7 per cent that it furnished in 1941. The district had an estimated basic daily oil allowable of 623,242 bbl. on Dec. 31, 1942. Approximately 31.8 per cent of the production in Texas during 1942 was supplied by this district, compared with 33 per cent during 1941- Changes in the annual production of newer and flush fields in this district are attributable either to a difference in the number of wells producing during the year or to changes in basic allowable and number of shutdown days due to shifting market dconditions brought on by the war. All regularly prorated fields in the district were shut down 123 days. Major exceptions were the East Texas field, closed128 days; Hawkiis, shut down 106 days; and Cayuga, Sulphur Bluff, Talco, and Rodessa, which

Jan 1, 1943

By Chauncey L. Berrien

The United Verde Copper Company's mine is at Jerome, Ariz. The orebodies arc of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. Three types of ore are mined; schist porphyry and the so-called "heavy" or "massive sulfide" ore. Approximately 50 per cent. of the total tonnage mined at present is of the latter class. A representative analysis of this ore indicates 42 to 46 per cent. sulfur. Because of the high sulfur content, blasting in this ore is an extremely hazardous operation. not only does it endanger the lives of men who may be in the mine at blasting time but it also becomes a potential fire menace when timber is in close proximity to shots being fired in these massive sulfides. The origin of the fires of 38 years ago, embers of which are glowing to this day, may perhaps be attributed to dust explosions due to blasting in the massive sulfides of those early square-set stopes. Dust Explosions Dust explosions in coal mines are a common source of mine disasters. That such explosions may be of common occurrence in metal mines is not generally known, but it is known that metal-mine dust will explode and such explosions have been investigated by the U. S. Bureau of Mines at the Pittsburgh Experiment Station. Samples of "heavy sulfide" ore from the United Verde mine were used in the tests. After studying the results of the tests it was concluded1 that: 1. Dust explosions were initiated in sulfide ore dust in the gallery with a charge of as low as 75 g. of 60 per cent. gelatin dynamite. 2. The exploding dust generated considerable pressure.

Jan 1, 1930

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By F. L. Holderreed

A choosy in what they would smelt. The furnace charge had to be coarse, and it had to be rich. They discarded fines in excess of about 1/10 the total weight. They wanted 10% copper content and fussed about anything with as low as 5%. They concentrated the copper content of the charge as much as they could by prior selection. They roasted off enough sulfur to further enrich the copper content of the succeeding fall of matte (a melt of cuprous and ferrous sulfides or Cu2S.FeS). Then they desulfurized the iron and fluxed it by carefully adding silica (quartz, not silicates) for a slag of lower density than the cuprous sulfide (Cu2S or white metal). After skimming off the slag, they further desulfurized the white metal by blowing the molten bath with compressed air. The result was blister copper. Yesterday Their techniques and furnaces? Some experimented with mechanically rabbled roasters, but their standard roasting practice was burning coarse sulfide ore in 250-ton heaps. These heaps, approximately 24 x 24 x 6 ft, were burned for about 75 days down to 6-10% sulfur. The turnaround time for a given roasting position was 100 days. Assuming the base was a hearth, the calculated rate of treatment was on the order of 0.004 tpd per sq ft.

Jan 1, 1971

By WALTON H. HAMILTON

THE demand for "production control" has, like the poor, been with us always. With the development of the nation, the accumulation of business experience, and a maturing understanding of how our many and varied industries work, it is increasingly evident that an uncontrolled output is a source of great mischief and that order and performance demand a control of production. To see clearly the demand for "production control" we must look in detail at the ways in which industries operate. General pictures, grand aggregates, situations as "wholes," and smoothed curves are likely to be deceptive. An industry may seem to keep the even tenor of its ways, and yet the establishments which made it up may experience a great range of fortunes. A nice bundle of statistics may show in the aggregate a lovely regularity which is not shared by the firms which make up a trade. An industry may appear to be reasonably profitable, and yet the profits may be very unevenly distributed. The people in an industry, and dependent on it, are managers, laborers, stockholders, creatures of flesh and blood, such as you and I. General pictures and abstract statements must not blind us to what is happening to firms, corporations and individuals.

Jan 1, 1929