Search Documents

By Will B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 5, 1960

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

By L. VOGELSTEIN

OUTSTANDING among the year's events in copper has been the reimposition of an import duty of 4r. per pound in this country which became effective June 21. In consequence of this action by Congress, the Ottawa Empire conference recommended a duty of 2d. per pound equivalent at normal rate of exchange to our 4c. duty, on all copper originating outside of the Empire. Lip to the middle of this year only Russia and Japan had a closed market; the import duty on copper in Russia is 30 per cent ad valoremm and in Japan about 2c. Russia's consumption has always been in excess of production and she has imported from 2(1,000 to 40,000 ton, of copper per annum. Japan, with a production of 6,000 to 7,000 tons per month, has absorbed, in normal times, its production, but during recent: sears has exported varyiug quantities in 1929. 2,200 ton-: in 1930, 2,700 tons, and in 1931. 3,600 ton-. Aside from the-e two countries, the international market has heretofore been free. It and when the British Empire duty become, effective the world's markets will be divided into four unit: 1. Russia and Japan, 2. United States. 3. British Empire. 4. Rest of the world. The world's production at present is rennin it the rate of 930.000 tons per annum. This year's production will be over 1,000,000 tons because the several curtailment did not become effective until the second quarter. consumption will be slightly in excess. Deducting from 30,000 tons Russia's and Japan's production of 121.000 tons, 806,000 tons is left divided a, follows:

Jan 1, 1932

By W. T. Allan

RAW bituminous coal has been in general use as a blast-furnace fuel in Scotland for the last century, and although its use has now been largely abandoned and it has been replaced by coke in the majority of the few furnaces which are at, present in blast in this country, coal-smelted pig iron is not yet a thing of the past; it is still being produced and mar-keted in competition with the more cheaply smelted product of the coke-fired furnace. Various factors have influenced this change in practice; the once plentiful deposits of coal of a suitable nature for the blast furnace are now not so easily obtainable; native blackband and clayband ironstones which are easily smelted in the coal-fired blast furnace, although still far from being exhausted, are not available except at a. cost that is somewhat higher than that of imported ores, making them unattractive to the ironmaster that is compelled by circumstances to smelt his iron at the lowest possible cost. Within the last 15 years overproduction of synthetic nitrogen has led to progressive reductions in the price of sulphate of ammonia, the recovery of which together with the other by-products before that time materially assisted in reducing the working costs of the coal-fired furnace. Now the sale of the by-products recovered yields a diminished profit. When the cost of the product is the only consideration the small, slow-smelting, coal-fired blast furnace cannot compare with its large, modern, coke-fired competitor. Other `considerations do not by any means all support the same side of the argument. In the smelting of pig iron to be used in the manufacture of steel where the quality of the final product depends so largely upon the control of the conversion process and so much less upon the physical quality of the pig iron used, the physical properties of the pig iron do not exert any appreciable influence upon the quality of the steel produced, therefore the methods employed in the smelting of the pig iron matter but little so long as the requisite chemical composi-tion is reached. On the other hand, in ironfounding where the simple melting of the pig iron, which is the only treatment it receives before being cast into its final form, does little or nothing to modify its original charac-

Jan 1, 1937

By Charles Jackson Abrams

MINING is one of the major industries of the Rocky Mountain region and since the United States became involved in the present World War, all mines have been called upon by the Government for the maximum production of the strategic metals necessary. Operating under the most adverse conditions, such as priority requirements, slow delivery of necessary material and equipment, labor shortages, and freezing of all wages, which still permitted some industries to pay higher rates than were allowable in the mines, thereby drawing labor from the mines; and the United States Employment Service continually giving mine labor certificates of availability; these and many other problems made mine operation particularly difficult. Yet, in spite of these obstacles, the mining industry, either through its own resources or through Government subsidies in the form of loans or premium prices for strategic metal, have and still are making an all-out effort to meet Government demands. They, without question, have played a major role in assisting the war effort.

Jan 1, 1945

The curve of Fig. 3 for pyrite requires modification. There 11% a range of pH values from 6.2 to 7.8 for which no cyanide is required to prevent contact. From 7.8 to 11.3 a small amount of cyanide is required, with a sharp maximum of 20 mg. per liter at pH=9.6. The mistake arose from considering too few solution compositions (17 were considered) in constructing the curve. Subsequent work with other collectors indicates that the corrected curve is typical for such systems; it illustrates the further development of the dip in the pyrite curve of Fig. 5.

Jan 1, 1938

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By J. M. Neilson

The occurrence of iron ore deposits in the State of Western Australia has been known at least since the 1930's,3 but the true significance of the deposits has only come to light within the past four years. Although they are widely distributed throughout the State, it is now known that more than 90% of the available iron ore reserves are located in the "Hamersley Iron Province". Western Australia may well contain the world's largest known reserves of iron ore. Recent reports place this reserve at 15 billion tons and an even higher figure may appear in the future. LOCATION, CULTURE AND COMMUNICATIONS It is difficult to comprehend the immense size of Western Australia (Fig. 1). The State occupies almost one million sq miles and it is more than 2000 miles from north to south. More specifically, it stretches from the 14th to the 35th parallel of latitude south. The Ophthalmia Region in the Hamersley Iron Province is barely halfway up the long dimension of the State. Nevertheless, the region is 800 miles north of Perth, a distance comparable to that from New York to Chicago or to that from Chicago to New Orleans. The Hamersley Iron Province (so named in 1963 to distinguish it from the Pilbara mineral district adjacent to it on the north) covers an area of approximately 30,000 sq miles in the northwestern part of the State. It extends in a roughly oval form from the Indian Ocean to the Gibson Desert of the interior, a distance of about 300 miles. With the exception of the small coastal towns of Onslow, Roebourne and Port Hedland and a few other communities such as the asbestos-mining town of Wittenoom, the region is very sparsely populated. Sheep and cattle stations are scattered thfough the region and these and the main towns are connected by truck tracks and a few main highways. Voice communication is almost entirely by the short-wave radio net operated by the Royal Flying Doctor

Jan 1, 1965

By C. Burton Clark, J. Spotts McDowell

Refractories are defined as "materials having the ability to retain their physical shapes and chemical identities when subjected to high temperatures," or as "nonmetallic materials suitable for the construction or lining of furnaces operated at high temperatures." While resistance to "high" temperatures is thus the primary requirement for refractory materials, it is by no means the sole requirement. They must be able to withstand thermal shock resulting from rapid heating or cooling; other stresses induced by temperature change; pressures from the weights of furnace parts or contents; mechanical wear (abrasion) resulting from movement of furnace contents; and chemical attack by heated solids, liquids, or gases. Refractories of many kinds are needed for the many and widely diversified industrial applications. Those in greatest demand are classified on the basis of composition or properties into a few main groups, known as alumina-silica, silica, basic and insulating refractories. In each of these groups there are several classes. In addition to those included in the main groups, there are various special refractories, including silicon carbide, carbon, zircon, zirconia, alumina, and several others. Alumina-silica refractories comprise two main divisions: fire clay and high-alumina. The alumina content of fire-clay refractories covers the range from about 45 pct to 18 pct, and the silica content from 50 pct to 80 pct. The alumina content of fired high-alumina refractories ranges from about 99 pct to 45 pct, and the silica content from about 0.5 pct to 50 pct. Silica refractories of the different classes contain 94 pct to 97 pct silica. Basic refractories include periclase (magnesite), chrome spinel, forsterite, and dolomite. Refractory materials, including insulating firebrick, are supplied mainly as preformed shapes. Other products include bonding mortars and high temperature cements, ramming mixtures, plastic firebrick, hydraulic setting castables, dead-burned grain magnesite, and dead-burned dolomite. Refractory brick are classified on the basis of their physical form as Standard Sizes and Special Shapes. The Standard Sizes are brick of certain definite sizes and relatively simple design which are used in sufficient amounts to permit quantity production. The brick most widely used are the standard 9 in. X 4 ½ in. X 2 ½in. and 9 in. X 4½in. X 3 in. straights and corresponding series of sizes. All brick of nonstandard dimensions are regarded as "special shapes." They include a wide variety of brick regularly used for specific services, such as baffle tile for boilers, checker brick for regenerators, and others; together with shapes of special design manufactured on particular orders from designs submitted by the user. Not included in the broad classifications of Standard Sizes and Special Shapes are several specific-service refractory products, usually made by companies which specialize in their manufacture, or in some cases by the consumers themselves. These products include

Jan 1, 1960

COLUMBIA SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON FRANK A. Ross The first meeting of the Columbia Section was held on March 24, as a part of the 1916 Northwest Mining Convention which was held under the -auspices of the Spokane Mining Men's Club assisted by the Spokane Chamber of Commerce, the technical program being in charge of the Spokane Engineering and Technical Association assisted by the local sections of the A. I. E. E., A. S. C. E., and A. I. M. E. The program of the successive sessions was carefully arranged with view to its application to mining, and in addition to the technical program there were exhibits of ores, minerals, devices, etc., of interest to the delegates, who numbered over 500. A portion of the program was also arranged with special reference to the requirements of the prospector and miner. A reception, a banquet, a complimentary luncheon, a regular daily call' of the Stock Exchange, a visit to the High Schools and to one of the substations of the Washington Water Power Company and to the Union Iron Works kept the visitors entertained, the ladies being looked after by a special committee of ladies who held open house during the entire week. Several important resolutions were passed by the Convention and one by the Columbia Section, A. 1. M. E. With Stanly A. Easton, chairman, presiding, the Columbia Section, American Institute of Mining Engineers, occupied the time between 2.00 and 5.30 p.m., March 24th, the Moorish room of the Spokane hotel being filled with members and their guests. "The Apex Law and the Mineral Surveyor" was a paper presented by F. W. Callaway and generally dis-cussed because of its local application in the Coeur d'Alenes, the conclusions being reached after expensive litigation between two of the large mining operators in that district.

Jan 6, 1916

By Jo. E. Sheridan

The Dawson coal-mines are owned aid operated by the Stag Canon Fuel Co., of which Dr. James Douglas is President and E. L. Carpenter general manager. The property is situated in Colfax county, N. M., and the openings now in operation are in townships 28 and 29 N R. 20 E., and township 28 N E. 21 E., shown in Fig. I. The mines are part of the southern end of the Raton coal-field, which extends north into Colorado and embraces many coal-camps of the Trinidad section. II. Geology. Geologically, the coal-measures, commonly known as the Laramie series of the Cretaceous system, have x thickness of about 800 ft. in the vicinity of Damson. The coal makes an excellent coke, and, according to some authorities, its coking properties are due to the action of intruded sheets and sills of igneous rock, the sheets occasionally thickening into masses resembling laccoliths, at such places making nearer approach to the coal and sometimes producing small areas of natural coke. There are but few dikes throughout the entire southern portion of the field and little or no faulting along the dikes. In some parts of this great coal-field the intrusive sheets are far removed in the green shales below the coal-measures, and are so much altered as to be difficult of identification. There is but little disturbance of the strata throughout the Raton coal-field in as far as it extends into New Mexico. There are two workable seams in the coal-measures, and two or three smaller coal-seams, ranging from 1 to 2.5 ft. in thick-

Jan 1, 1910

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

NEW YORK SECTION ALLEN H. ROGERS, Chairman, H. C. PARMELEE, vice-chairman, FOREST RUTHERFORD, Vice-chairman, W. S. DICKSON, Secretary, 71 BROADWAY, NEW YORK, N. Y. J. E. JOHNSON, JR. F. T. RUBIDGE, Treasurer, P. G. SPILSBURY A meeting of the New York Section was held at The Machinery Club on Friday evening, Oct. 4, 1918, The Chairman, Allen H. Rogers, presiding. The CHAIRMAN.-MOST of us, I suppose, have been affected more or less by The request of The Fuel Administration that we leave our automobiles standing in The garages on Sundays. We shall all be interested in hearing about The situation that has called forth This, request, and The Oil Administrator, Mr. Requa, has kindly come from Washington to Tell us about it. MARK L. REQUA.-I am very glad To Tell you about the oil problem during This war period. The United States is supplying by far The greater part of all The petroleum products consumed in Great Britain, France and Italy. In addition To This, we have had To supply a marked increase in our domestic consumption, not only of The refined products, but of fuel oil as well. The combination has put a strain on The oil industry, which it is very difficult To meet. The oil companies, being under contract, had no option as To who should get Their oil first, and They were delivering pro rata To everybody; manufacturers of furniture were getting oil with The same regularity as Those who were making aeroplanes or munitions, and The oil companies felt that something should be done. The first order with which I had. anything To do was The priority list for The delivery of fuel oil. That list contained 12 classifications, beginning with bunker fuel and railroads, and you will realize The complexity of The situation when you hear that munitions plants are in class 11. The priority list held during The winter, but transportation became so bad, because of The number of ships that were Taken for trans-Atlantic use, that some of The oil companies were not able To deliver more Than about 60 per cent. into class 5, and nothing beyond that point. To add To the Troubles, the Tank-car mileage fell off. The average for 1917 was about 36 miles per car per day. in January, 1918, it dropped To about 8 miles, and it must have been nearly zero in The early part. of February. Because of The extremely severe winter, furthermore, pipe lines were not delivering anywhere near Their normal capacity. A new priority list has recently been promulgated, introducing a few slight changes. Natural gas has been brought under its provisions, and it has been extended To include The Pacific Coast, which was not considered necessary last winter. The situation in The gas industry is not satisfactory; it is estimated that There will be a decrease of 10 To 20 per cent. in The quantity of natural gas available This winter, as compared with last winter.

Jan 11, 1918

By S. Gstalder, J. Raynal

Consideration was given to simple tests which could be performed on rocks to give a measure of rock drillability. Various methods of breaking rocks were considered and the hardness test developed by Schreiner was selected for this study. The test involves application of an increasing load on the rock face through a flat-faced cylindrical punch until rupture occurs. Test results show that hardness is a good measure of the breaking strength of rocks. Useful relationships are shown to exist between hardness and other physical quantities such as specific disintegration, Young&apos;s modulus and sonic velocity. Specific disintegration (volume of rock broken per unit of work input) provides a possible means of comparing the effectiveness of other methods of rock breakage. The relationship between hardness and sonic velocity may be very significant for it may be possible to deduce rock drillability from sonic log data. provided that a mineralogical factor is taken into account. TO test further the results of the work, laboratory drilling tests were performed which closely simulated down-hole pressure conditions. Correlations of drilling results with rock hardness measurements were quite good. It was concluded that rock hardness, as measured in the laboratory or as deduced from sonic logs, could be used in relations for predicting rock drilling performance. INTRODUCTION Drillability of rocks cannot be defined in an absolute manner by a single quantity or measured by a single test. Resistance of rock to drilling depends to a large extent upon the means used for rock destruction. This complicates drillability classification of rocks for there may be as many classifications as there are methods of rock breakage without known functional relations between them. The objective of this work was to develop. in terms of rock destruction behavior, means of selecting the best drilling method for a given rock or the conditions for optimum output from a given drilling method. ANALYSIS OF ROCK DESTRUCTION TESTS Gauthier and Baron&apos; have reviewed the many test methods which have been developed for determining the resistance of rocks to breakage. These include drilling tests, punch tests, scratch tests, resistance to shock, wear tests, etc. A standard drilling test might be to determine the time required to drill a standard depth (1/16 in.) in a rock using a bi-cone microbit (1 1/4-in. diameter) when a standard load (417 Ib) is applied at a standard speed of bit rotation (110 rpm). From the standpoint of similarity, the results of microbit drilling tests would seem to be most representative of the several methods suggested above. However, evaluation of drilling performance by this method is only qualitative and cannot be applied directly to actual drilling conditions. Punch tests basically measure rock hardness. Punches of various shapes and sizes, including small cones for Vickers&apos; and Knoop&apos;s tests, the wedge for Epstein&apos;s test and the right circular cylinder for Schreiner&apos;s test, have been used. Results of these tests lead to a quantitative hardness classification which would seem to be related to the resistance of rock to bit-tooth penetration. Scratch tests are related to the resistance of rocks to abrasion such as would be encountered in drilling with diamonds. Either the width of the scratch obtained at a fixed load or the load required to give a scratch of a fixed width may be used to evaluate surface hardness of the rock. This should be related to the resistance of the rock to wear. The above tests, and probably many others. give relative measurements of the breakage or destruction characteristics of rocks. There is no direct relation between results of these tests and the drillability of rocks. Also, the tests each measure different quantities which have different dimensions and they do not permit direct comparison of numerical values. As one step in rectifying the above difficulties. it is proposed that the results of all test methods be expressed in terms of volume of rock destroyed per unit of work required; this is referred to as "specific disintegration". Test results may then be reported in a form which shows both a classification of rocks in regard to each method and a comparison of methods with regard to each rock. The disadvantage in using specific disintegration is the difficulty of measuring this quantity with accuracy. The volume of rock damage is difficult to measure. as is the true value of work input. Rock heterogeneity adds to the

Jan 1, 1967

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary): I think very highly of the novel and ingenious device of Prof. Richards for analyzing the movement of the various elements of the jig; it is a method that certainly seems to promise valuable results, if we could only make certain that these various indicator-appliances have no effect upon the action of the jig. I would like, however, to suggest that in future experiments the connection between the plunger indicator-rod and the pencil should be made by means of parallel motions, so as better to reproduce the rectilinear motion of the piston. I should expect, if this were done, that the " curve " of the plunger in the Harz jig, at any rate, would be represented either by straight lines or else by quite regular curves, according to the method by which the plunger is set in motion; the apparent combinatioil of straight line and curve seems difficult to explain. With respect to the water-curve, I am afraid I am completely at fault, but no doubt Prof. Richards can explain my difficulty. In Fig. 2, the areas of the screen-side and the plunger-side of the jig are equal. If the piston be a fair fit and the bottom of

Jan 1, 1897

By A. L. Moore

KAISER Bauxite Co., a subsidiary of Kaiser Aluminum & Chemical Corp., has been mining and shipping Jamaican bauxite for over a year. On Feb. 10, 1953 the first boat load of bauxite left Port Kaiser, Jamaica, for the company&apos;s alumina plant at Baton Rouge, La. To provide its own source of the aluminum ore, a Kaiser Aluminum & Chemical Corp. exploration party started initial reconnaissance in 1947. This work, and subsequent exploration, led to the acquisition of reserves sufficient to warrant a full-scale mining operation for several decades.

Jan 3, 1954

The Petroleum Division met at Fort Worth, Texas, Oct 8-9 $ The headquarters were at the Blackstone Hotel, the attendance was 175 Sixteen papers were presented, 12 of them by the authors The technical program was built up around four major topics. Drilling, Production, Engineering Education and Metallurgy There were four sessions, two each day More than 100 were present at the luncheon on Friday noon, which was addressed in turn by President Lovejoy, George Otis Smith

Jan 1, 1937

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.&apos; The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.&apos; The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.&apos; Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958