Search Documents

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By R. E. H. Pomeroy

Early in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (I) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application, the coal and air mixture can be piped where needcd. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins. The plant is operated entirely by electric power. All alternating current is 550 volts, 3-phase, 60 cycles. The pulverized-coal feeding niotors and control mechanism are operated by 220-volt direct current supplied by motor-generator sets in the building. Autamatic push-

Jan 1, 1921

By H. M. Howe

The chief purpose of this note is to call attention to the triaxial diagram as a convenient means of illustrating the properties of slags, and by this example of its use to commend it to those inclined to graphical studies having other possible applications. Explanation.—In the common or di-axial diagram, the properties corresponding to any point are determined by its perpendicular distance from each of two axes. For example, in an ordinary stress-strain diagram the properties of a given point in the curve are, first, a stress cd so many pounds per square inch, because its perpendicular distance from the horizontal axis of the diagram corresponds by the vertical scale to that stress; and second, a strain or elongation of so many per cent., because its perpendicular distance from the vertical axis corresponds by the horizontal scale to that elongation. It happens that, as a matter of convenience, we habitually place these two axes at right angles to each other; so that our measurenieilts happen to be made not only at right-angles to

Jan 1, 1899

By Ralph M. Hunter

Until recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged breakdown did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to bypass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdi-ness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, there- fore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 1946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1949

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By E. R. Kaiser

COAL research during 1941 had a marked increase in activity on problems bearing directly on furthering the increased and improved use of coal in homes and industry. Coal producers and fuel engineers expressed a greater interest in its practical possibilities and the coal laboratories have shown an increased interest in applied research, of value at once or in the near future to industry and the public. A large volume of accomplishment in mining, coal analysis, and the fundamentals of coal constitution and coal chemistry also continued to fill the storehouse from which applied research and fuel engineering of the future can draw valuable data.

Jan 1, 1942

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.' The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

THE name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. GEOLOGY The ore deposits of Copper Mountain are related to the Copper Mountain stock, which is an ideal example of the magmatic differentiation in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanics and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial granitization of some of the volcanics. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. THEORETICAL ESTIMATE OF STOPING WITH THE DIAMOND DRILL After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping. Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1945

By Guy Bjorge

IN recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No; 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B: & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and-Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Further-more, assurance of safety and uninterrupted operation required- two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent.

Jan 1, 1935

By C. E. Corson

Discussion of the Paper by C. E. Corson, which was presented at the London Meeting, July, 1906. (See Bi-Monthly Bulletin, No. 11, September, pp. 725 to 742.) ALBERT SAUVEUR, Cambridge, Mass. (communication to the Secretary*) :-On close examination I think it will be found that the evidence by which Mr. Corson claims to have shown the inaccuracy of a statement I made a few years ago, is far from convincing. This statement is:- "Hot work, as such, has no influence upon the structure of the metal. Indirectly, however, by retarding crystallization until a lower temperature is reached, it may influence its structure most decidedly ; but the same results could be accomplished by heat-treatment alone, i.e., by reheating the unworked metal to the temperature from which the unworked piece was allowed to cool undisturbedly." The Metallographist, vol. ii., p. 267 (under the head of "Changes of Structure Brought About by Work"). Of the two pieces of steel tested by Mr. Corson, one was worked and finished at a " cherry red " and ' the other reheated to a cherry red, and the assumption was made that, in both cases the temperature was about 715° C., although no pyrometric device was used to record it. The possibility of considerable difference in temperature alone is so great as to invalidate Mr. Corson's inferences. The apparent temperature, moreover, is so close to the critical point of the steel as to render any conclusion very hazardous. -It is not at all evident that the annealed piece was reheated past its critical point, in which case reheating would have had practically no effect. Nor is it evident that the piece forged and finished at a cherry red was not actually below the critical point, which, by definition, I have called cold worked. Mr. Corson's explanation that " Under proper reheating, on the other hand, the steel becomes a solid solution from which crystals of approximate homogeneity and uniform size may separate" will not be readily understood.

Jan 1, 1907

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612' F. (322' C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By Henry E. Colton

NeaR the town of Christiansburg, Va., occurs a singular feature in topographical as well as geological structure, which may be said to have an important bearing on a large area to the southwest. The great water-shed ridge, which divides the waters flowing into the St. Lawrence from those flowing into the Atlantic ocean, coming southwestward, forms all of what was the boundary of Maine as agreed upon by the treaty of 1783, and a part of the present boundary, all of the northern New Hampshire boundary, and entering Vermont, continues south of Lake George. Passing irregularly through New York, it enters Pennsylvania, and there bifurcating, sends one prong to the west as a divide between the waters of the lakes and the Ohio, while the other becomes the steady, regular ridge which gave it the name of Alleghany, and thus passes on southwestward through Virginia. At no point has it ever been the geological divide. Its course, commencing in the Archean rocks, has passed through nearly every series of formation, and comes into Virginia in the Carboniferous strata. The geological divide—the line between the fossiliferous and the non-fossiliferous rocks—lies, in Canada, to the west of it, but from New York south into Virginia is far to the east. Reference to Dr. Hitchcock'k map will show this. But at the locality noted these positions are changed; the water-divide becomes the eastern chain, and the geological divide is the western, returning, it may be said, to the positions occupied in the region where they originated. These relations are shown on the large map accompanying the present paper. For several miles, the track of the Norfolk and Western Railroad

Jan 1, 1888

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company's Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;' in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany's own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. 'ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4'8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

With the exception of the mentions of coal in Illinois in the period 1660-1680, already referred to, the first coal found in the United States was in the James River, Virginia, field. In 1699 a large tract of .land above the present city of Richmond was allotted for a settlement of French Huguenots by the colonial, government, near the present Manakin, about fourteen miles above Richmond. They soon found coal, tradition says it was uncovered by a hunter pulling out a small tree in a. steel) bank near a stream, and Colonel William Byrd, F.R.S., the most prominent man of his day in the colony, wrote to the Colonial Council of Virginia, May 10 and 11, 1701: "The 10th of May, last., I with Coll. Randolph, Capt. Epes, Capt. Webb, &c., went up to the new settlements of ye French Refugees at ye Manaken Town.... We went tip to ye Cole, w'ch is not above a mile and a half from their settlement on the great upper Creeke, w'ch, riseing very high in great Raines hath washed away the Banks that the Coal lyes bare, otherwise it's very deep in the Earth, the land being very high, and near the surface is plenty of Slate.", Some of the Frenchmen were evidently familiar with the use of coal, as on May 22, 1702, "David Menestrier a black smith and one of ye french Refugees Inhabiting at Luciana Petitioning his Excellency that he may have leave to use ye coal mines lately discovered there for his forge his Excellency by and with ye advice of ye Council loth hereby give Leave to ye said David Menestrier to take what coales he shall want. out of ye said Coal mine for ye use of his forge according to ye Prayer of ye said Petition."2 There was some uncertainty about the grant of these lands to the Huguenots which caused the request for leave to use this coal, as a Virginia patent in its usual form allowed the owner to mine all minerals excepting gold and silver, which were subject to royalties for the Crown. After the visit to the coal above mentioned, "Wm. Byrd, understanding the land had not been granted to the French, took out a patent for 344 acres, including the same, (the coal) which patent was dated October 20, 1704".3

Jan 1, 1942

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.