Search Documents

By O. G. Lellep

Modern shaft kilns in Europe are fully mechanized and burn cement of acceptable quality at 700,000 Btu per bbl and lime at 3.2 million Btu per net ton. Rotary kilns for cement have increased in thermal efficiency by using exit gas heat for preheating incoming raw material and by recovering heat from outgoing clinker in air-quench coolers. The dry process Lepol or ACL kiln has the lowest fuel consumption, 580,000 to 630,000 Btu per bbl, and very low dust loss, about 1 pct weight of clinker. The Holdebank-Gygi system reaches 720,000 Btu per bbl. The calcinator kiln for the wet process consumes 1.1 million Btu per bbl. IN every country economic circumstances prescribe the method used to produce a commodity at lowest cost. In Pennsvlvania a man's wages for working 4 hr buys a ton of coal wholesale; in Germany a laborer must work 40 hr, or ten times as long. In western Europe, therefore, conservation of fuel is of primary importance, and recent practices of burning lime and cement differ from those employed in the United States. 'This Paper presents data collected during a trip through western Europe in 1953. Considered uneconomical, shaft kilns for burning

Jan 1, 1955

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

Claims of 16 gold mining companies seeking damages from L-208 will be heard in Court of Claims starting Jan. 26. Earlier this year, judges ruled that 3 gold mining companies could sue for damages from the wartime order closing their mines. Congress later waived the statute of limitations thus permitting other gold miners to get in their claims. Despite power shortages third quarter production of aluminum exceeded that of the previous period by 2.2 pct. However, September production was 16 million lb less than in August. Hewitt-Robbins, Inc. dedicated a new $1 million addition to the company's Buffalo, N. Y. belt conveyor plant. New equipment, including a $220,000 press, will make belts up to 70 in, wide, compared with the former limit of 60 in. Charges of a tin cartel in Malaya are not backed up in the latest U. S. Government report according to the Malayan Tin Bureau. The U. S. mission reported that it "did not discover any evidence of curtailment of tin output by the mining and smelting industries." It noted that guerilla activity had halted exploration and expansion attempts by producers.

Jan 1, 1952

By David W. Brunton

I. INTRODUCTION. THE list of our past-Presidents comprises the names of runny who, in their official addresses, have sketched the current progress of the arts and professions with which they were familiar. Such addresses are, in my judgment., highly useful, setting forth the results of our own work as a. society, and recalling to our minds the particular lines in which discussion would prove most fruitful. . Following this course with some hesitation, I venture to offer an outline of the recent improvements and the present situation in minim and metallurgy in the Western United States. The wonderful advances in mechanics, chemistry, and electricity have all combined to aid these arts to such an extent that. progress during the last decade has undeniably been more rapid than ever before in the history of the profession.. In all mining countries improved transportation-facilities, in many instances called into existence by the traffic created by the mines themselves, have done much- to enlarge the. field of operations by the reduction of freight-, operating- and living-expenses, thereby bringing lower-grade properties into the producing class. Under normal' conditions, as the age of a district in¬creases, all these differentt factors should combine to off-set. the augmented costs attendant on deep mining, and greatly tend to prolong the profitable life of the mines. The more recent and important improvements in our Western mining-practice which have contributed most toward the advancement of the art may be briefly summarized as follows; but, before beginning this portion of ray address, I wish to thank most heartily the many engineering friends who have so

Sep 1, 1909

By E. J. KENNEDY

METHODICAL AND EFFECTIVE: thus may be characterized the fall meeting of the Iron and Steel and Institute of Metals Divisions at the Hotel Statler, Buffalo, N. Y., on Oct. 4 and 5. Approximately 200 registered. Interest centered 1111 the technical papers which were keenly followed, with substantial discussion: During the entire week of the National Metal Congress (Oct. 3 to 'i), there were also other sessions of interest' to metallurgists, directed by the America11 Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron arid Steel and Machine Shop Practice Divisions of the American Society of Mechanical En,' the Wire Association and the American Drop Forging Institute. The National Metals Exposition at the 174th Regiment Armory was well attended.

Jan 1, 1932

By Linn M. Farish

SOVIET RUSSIA reserves must be stupendous. In 1937 I. M. Goubkin placed the reserves of all categories it approximately 48 billion barren which was about twenty billion horn Is in excel:, of all the oil produced in the world since 1857. It is not unlikely in fact it is probable, that these huge stores of petroleum may ultimately be proven to exist within the present boundaries of the U.S.S.R. The size of the country is almost beyond imagination it is 2.7 times as big as the United States. Great sedimentary basins exist in all its different geological provinces, much of which are entirely untested and barely prospected. Oil in commercial quantities is actually produced from formations in every period from the Devonian to the Pleistocene. In the Emba region alone, 300 salt domes are known with an estimate of 700 still to be found. Only 22 of the 300 have been drilled and all showed oil. Of the 22 domes drilled six are now producing. There are 400 mapped structures reported in Azerbaijan

Jan 1, 1940

By G. S. Baker, S. H. Carpenter

Langenecker has reported significant reduction in strength of high-strength metals during ultrasonic t'ibration. Decreases in static yield stress an order of magnitude greater than the calculated stress amplitude of vibrations were reported by him for a stainless steel and for tungsten. in the present work, attempts were nzadc to verify such large reductions in yield and flats stresses using resonant librations of measured amplitudes. The results show that both the soft metals (copper and aluminum) and the high-strength metals (sleels) hare reductions in yield and .flow stresses no larger than the stress amplitude of libration. BLAHA and Langenecker,' investigating the effect of vibratory stresses on the deformation of zinc and aluminum, found a decrease in the static yield and flow stresses approximately equal to the vibratory stress imposed. Langenecker later extending this work to high-strength metals such as stainless steels and tungsten2 found a much larger effect. In these metals the static yield and flow stresses decreased by an amount more than an order of magnitude greater than the calculated vibratory stresses. It was suggested that this phenomenon could be a serious hazard to high-strength structures in an acoustic environment, such as a large rocket at launch, or could be used advantageously in the working of hard-to-work materials such as the refractory metals. Langenecker and others3 have investigated the effect of high-amplitude vibrations on many metal-forming operations. The results have been quite favorable with usually a large decrease in the energy necessary for the forming operation. The processes, however, involve large frictional forces and it is not clear whether the decreases in forming forces are to be ascribed to decreased friction or to decreased flow stresses. The present paper reports an attempt to determine the effect of accurately known vibratory stresses on the static yield and flow stresses. I) EXPERIMENTAL TECHNIQUE The standard multicomponent resonator technique for measuring internal friction has been adapted to allow simultaneous high-amplitude vibration, internal-friction measurement, and tensile deformation. This has been described in detail elsewhere.4 Longitudinal oscillations of approximately 50 kc frequency are excited in a multicomponent resonator by a quartz transducer. A second transducer measures the amplitude of vibrations. Fig. 1 shows a schematic drawing of the resonator and grip arrangement and the displacement pattern produced. Since the centers of the dummy bars are at displacement nodes, they represent points where attachments will not materially affect the vibrations. The force is applied by a standard Instron tester. The sample may be deformed while simultaneously vibrating at up to 104 strain amplitude. 11) EXPERIMENTAL RESULTS The effect of high-amplitude vibrations on the yield and flow stresses of copper. aluminum, tantalum. a soft iron, and a stainless steel has been measured. In addition samples of tungsten vibrating at stress levels up to 10' dynes per sq cm have been subjected to static stresses near the static yield stress with no indication of macroscopic deformation. Fig. 2 gives typical results for 99.999 pct polycrys-talline copper. A vibratory stress of 7 x 107 dynes per sq cm is applied at points "a" and removed at points "h". The behavior of aluminum is identical. In agree-

Jan 1, 1967

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By Robert Linton

AT its meeting on May 21, the Board of Directors approved the recommendations submitted by President Lovejoy and named a nominating committee for the year that is especially well distributed as to major technical interest and as to geography. As may be seen from the list published herewith, two come from the East, two from the Midwest, and three from the far West. Mr. Linton, the chairman, has been a valued member of the Institute for 36 years. A memorandum drawn up by Paul D. Merica, representing the A.I.M.E., and W. R. Barclay, representing The Institute of Metals of Great Britain, setting forth a reciprocal plan for special memberships in each Institute for members of the other, was discussed. Both societies already have formally approved the plan in principle and Dr. Merica was clothed with full authority to agree on a few small details that have not been settled, and conclude the arrangement in behalf of the Institute.

Jan 1, 1936

By N. A. D. Parlee, I. D. Shah, W. C. Phelps

THIS note reports on a continuation of a program on the thermodynamics of Fe-S-X systems in the "steel-burning" temperature range begun by Bock, Barloga, and parlee.' Small coils of 0.039-in.-diameter pure iron (Ferrovac-E) wire were equilibrated with Fe-S-0 melts in ingot iron crucibles under argon at 1324°C in the assembly shown in Fig. 1, the lower part of which was heated in a large Globar furnace. Fig. 1 shows (R) the coiled iron wire sample, (M) the Fe-S-0 melt prepared from desired proportions of ferrous sulfide and ferric oxide, (K) the iron crucible, (I) a mullite guide tube, (J) an alumina crucible, (L) alundum sand, (N) crushed mullite, (Q) hollow cylinders of K30 brick, (C) a steel rod, (B), (El, (F), (G), (P), and (O), details of brass water-cooled head, and (H) a mullite tube 2-3/4 in. ID and 26 in. long. The rod (C) bearing the sample could be removed at will and be replaced by a tube for sampling the melt, or by a thermocouple for comparing the melt temperature with a control thermocouple not far from the 2-3/4-in. mullite tube. After equilibration the iron coils were treated with acid to remove the outer layer of metal and then they were analyzed for sulfur by a standard combustion method. The melt samples were analyzed for oxygen by a variation of Lander's2 hydrogen-reduction method for mattes, and for sulfur by the ASTM combustion-iodometric method NO. E 30-47. When the results of some forty-two runs were examined it was found that the sulfur and oxygen contents of the equilibrated melts showed good consistency, in that the plotted compositions fell along the smooth curve shown in Fig. 2. The points on this curve represent the experimental compositions of melts in equilibrium with ?-iron (Fe-S-0) solid solutions. These solid solutions are saturated with sulfur and oxygen with respect to the melt and therefore have the same sulfur and oxygen activities as the melt. The curve drawn through the points therefore delineates the ? liquidus. It falls in such a position as to roughly confirm the liquidus curves of Hilty and crafts3 at 1200" and 1300°C which are

Jan 1, 1965

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By T. E. Watkins, M. D. Nelson

A method of determining the lime content of drilling muds proposed by Battle and Chaney* has been examined both in the Field Research Laboratories of Magnolia Petroleum Co. and in field drilling operations. This proposed analytical method is condensed as follows: Titrate one ml of mud and one ml of mud filtrate, each with 0.02 N H2SO4, to the end point with phenolphthalein. The volume of acid in ml required for the mud titration is recorded as Pm and that of the mud filtrate titration as Pf Calculation of the lb lime/bbl mud is accomplished by use of the formula, lb lime/bbl mud = 0.6 (Pm - 1.3Pf) - 0.6 The analytical procedure outlined by Battle and Chaney was found to be quite satisfactory when reasonable precautions are used in mud sampling technique. Calculation of lime concentration by the method proposed in the above publication, however, has given values that varied as much as 100 per cent from the known lime content, for muds of either high or low solids concentration. By use of a formula, lb lime/bbl mud = 0.26 (Pm-F1.Pf), based on chemical equivalents of acid required for titration, both laboratory and field data have been satisfactorily correlated with the known amounts of lime present in the muds. In this formula a correction, F1, or volume fraction of liquid in the mud, is made for the solid content of the mud. Pm and Pf * Paper on "Lime Base Muds," presented by J. L. Battle (Humble Oil and Refining Co., Houston, Tex., and P. E. Chaney (Sun Oil Co., Beaumont Tex.), at the 1949 Spring Meeting of the Southwestern District API Division of Production, Dallas, Tex. The analytical procedure has also had wide distribution in a trade journal, Kembreak, published by the Accuracy Rig and Tool Co., Houston, Tex, †Derivation of equation lb/bbl — grams/350 ml 1 ml 0,02 N acid = 0.000741 grams of lime 1 ml 0.02 N acid/ml lime suspension = 0.26 lb of lime bbl lb of lime/bbl = 0.26 (Pm -F1, Pf ) have the same significance as in the Battle and Chaney equation. Table I shows typical data employing both formulas in calculating the lime content of various lime muds. This suggested procedure ignores lime which is in solution in the mud. The solubility of lime in water, normally about 0.5 lb per bbl, is greatly decreased by the addition of caustic soda, and, in a lime mud, it is probable that the concentration of dissolved lime is of the order of 0.1 lb per bbl. Such an amount of lime can be ignored, since it is within the range of accuracy of the method.

Jan 1, 1950

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By Cadwallader Evans

MY endeavor in this paper will be to tell something of the accomplishments and current problems of the anthracite producer and to suggest some of the avenues for technical development that seem to me to be the most necessary and likely to bear fruitful results. The several subjects, that I find of most interest will be taken up individually with brief reference to the future trend. Underground Mining and Loading ?In this field great progress has been made in the last twenty years, beginning with the introduction of the scraper system. The electrical hoists for the operation of scrapers have been improved, and give little trouble, but there is an open field for the improvement of the auxiliary apparatus, particularly in the application of roller-hearing sheaves to the guiding of scraper ropes. Also notable in the last six or seven years is the introduction of shaker chutes, so that far more anthracite is now loaded over them than by scrapers. This trend should continue to be manifest, particularly if those who are looking ahead and who are charged with the development of this specialty continue constantly to study and improve the mechanical design of their shakers.

Jan 1, 1938

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

By AIME AIME

FIVE days, extending from Monday, Feb. 18 to Friday, Feb. 22, inclusive, will be required for the annual meeting this year. The first fours days will be devoted to reading and discussion of papers, general and committee business meetings, two lectures, luncheons, dinners and all the pleasures of a big, general reunion. The fifth day will be given over to an all-day excursion for both men and women by special train to West Point, in celebration of the birthday of the first President of the United States. Washington having been an engineer and now after one hundred and thirty-one years the country having selected as President another engineer in the person of Herbert Hoover, our own past president and honorary member, it is proposed to celebrate with a good old-fashioned picnic and inspect the school. The authorities at the Military Academy have undertaken to welcome the engineers and do whatever they may to make our pilgrimage notable. Other social features planned for the week are numerous. Luncheon will be served as usual at the building each day of the meeting to all members and guests. This year a very nominal charge will be made, primarily to overcome deficits due to irregular attendance. Monday noon, the Non-metallic Minerals Committee will lunch at the Engineers' Club and in the evening the Milling Methods Committee will dine there. The Annual Smoker will be held at Hotel Astor after dinner. Professional entertainment of high order is promised, but not too much to interfere with the numerous group reunions that characterize this func- tion.

Jan 1, 1929

By Charles Hart

In this paper it is the author's intention to show the extent and character of foreign ores now known to be available; these deposits may be in active production or held in reserve until economic conditions may make them active. He hopes to show the relation existing between these ores and the American supply, and which of the former are now producing or will in turn come into production when our better ores have been exhausted. This phase of this discussion must of necessity include some data as to the present rate of consumption and a study of the changes we may expect here and abroad in the general steel trade and its sources of supply in raw materials. It is obvious that the occurrence of coal, ore and limestone in relation to one another and the proximity of a market are the elements in control of this feature of the problem. If the foregoing situation is favorable, all the other questions may be solved, for it is clear that with proper basic conditions finance, labor and operations will fall in line. We present a short outline of the present methods of carrying on the foreign iron ore trade, believing that it is of general interest in comparison with our own highly specialized methods, and that with the exhaustion of our better ores we will be compelled to seek a part of our supply abroad. A partial list of iron ores, with incomplete analyses (Table I), is added, to give a better understanding of the general situation and explain to some extent the reason for things being as they are in the iron and steel trade of the world and to help in bringing this paper to an informing conclusion. The question of the world supply of iron ores has been a subject for study on the part of geologists and engineers for many years, and found its best results in the Eleventh International Geological Congress, appropriately held at Stockholm, Sweden, in 1910. The proceedings are published in two volumes and are undoubtedly the best records available on this subject at the date of publication. It should be borne in mind, however, that much has happened in the 20 years since these figures were assembled. There is just as much known ore at present as at that time, minus the quantity consumed, plus newly discovered reserves. The World War had great effect upon this situation; during that time explorations were greatly reduced and the settlements after the

Jan 1, 1929