Search Documents

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neu-mann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempts to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2. was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form 12111. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

Jan 1, 1928

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Richard H. Mote, W. C. Schroeder

The endlessly changing pattern of mineral supply and demand offers opportunity to the alert and can bring disaster to the unwary. The discovery of ore bodies, the invention of extractive processes, the provision of new transport facilities, the political stabilization of underdeveloped areas, and many other changes can increase supply dramatically. Such new outpourings of mineral wealth from ore bodies bring fortunes to their developers, and consumers frequently find their competitive positions decidedly improved by new and cheap sources of supply. On the other hand, operators of marginal properties can find competition from newly opened high-grade mines intolerable. Consumers that have depended on the products of nearby, high-cost mines may find new, remote, low-cost supplies advantageous only to their competitors. The invention of new prospecting methods can have spectacular effects. Shortly after World War I the discovery rate of petroleum pools began to decline. The leading prospecting technique of that day, the projection downward of surface reflections of geologic structure, was proving less rewarding. Prophets foretold an oil shortage in the near future. But at that very moment scientists were perfecting the application of seismic waves to reveal underground oil-bearing geologic structures. As these geophysical methods were put into commercial use the whole outlook changed-the problem of the 1930's became how to cope with the surplus from discovery, not how to meet the ever rising demand. Many lead mines were being abandoned as unprofitable about this same time because the penalties charged by smelters for the zinc in the ores and concentrates more than counterbalanced the payments for lead and silver. Then selective flotation (at the time called differential flotation) appeared,

Jan 1, 1959

By N. A. Tiner, Saara Asunmaa

The early stages of nucleation of vacuunz-deposited gold coatings on electropolished surfaces of pure nickel and binary alloys of Ni-A1 and Ni-Ti have been studied, employing carefully controlled temperature and vacuum conditions. The preferential nucleation of gold on slip-plane edges on the crystal surfaces gave rise to a very pronounced decoration effect which was used in studying the morphology of the pain boundaries, etch pits, and slip planes on crystal faces. Characteristic surface patterns were observed with local dimensional variations. Most pronounced geometric patterns were ohserved in the pain boundaries of nickel and on the crystal faces of Ni-A1 alloy. The nucleation behauior of gold indicates contamination on the Ni-T1 alloy and the getter properties of titanium are presented as a tentative interpretation for the detected contamination. The markings and imperfections on cleavage surfaces of crystals have long been observed by optical microscopy.1,2 Surface-replica techniques are also used to detect the smallest steps and structural details on crystal surfaces by electron microscopy. Recently, Bassett3-5 and Sella, Conjeaud, and Trillat 6 have shown that, when gold is deposited onto a rocksalt cleavage surface, there is preferential nucleation at steps and slip-plane edges on the crystal surface. This gives rise to a very pronounced decoration effect which is invaluable for revealing the lattice steps on a cleavage surface. According to Bassett,3 gold atoms arriving during vacuum evaporation at the crystal surface have a certain mobility on the surface after arrival, particularly at elevated temperature. If a significant

Jan 1, 1964

By D. L. Ritter, N. J. Grant, B. C. Giessen

Forty-six alloys covering the complete concentration range of the Nb-Rh system were examined by metallographic and X-ray methods; solubility limits of terminal ad intermediate phases and transformation and solidus temperatures were determined. There are nine intermediate phases; two eutectic, five peritectic, two eutectoid, and three peritectnid reactions were encountered. The experimental methods and the constitution diagram are described in Part I. Part 11 deals with the crys -tallography and relation of the intermediate phases. The Nb-Rh system was selected for study for three reasons: first, it was hoped that the anticipated similarity of the Nb-Rh phase diagram to the Ta-Rh1 and Ta-Ir2 diagrams treated earlier (see also Ref. 3) and to the Nb-1r4 diagram treated simultaneously would allow a crystallographic and comparative evaluation of the intermediate phases in these related systems; second, it was likely that the previous experimental methods could be carried over without significant change; and third, it was expected that the interesting mechanical properties of the a1 phase of the Ta-Rh and Ta-Ir systems would also be encountered in similar phases of the new systems, and that these phases could be investigated more closely. The phase diagram had not been treated fully in the literature; only brief surveys of some intermediate phases were found.5-7 It was attempted to cover the details of the phase boundaries, Part I, as well as to present the crystallography of the intermediate phases, Part 11. EXPERIMENTAL METHODS Specimen Preparation and Treatment. The following high-purity starting materials were used. 1) Niobium powder, 99.8 pct pure, mesh size -60 +200, from Wah Chang Corp., Albany, Ore. The analysis furnished by the supplier showed the following major impurities: Ta, <500 ppm; Zr, <500 ppm; 0, 300 ppm; Fe, 280 ppm; Ti, <I50 ppm; W, Si, <100 ppm; C, N, 30 ppm; all other impurities, <30 ppm. 2) Rhodium powder, ground sponge, 99.9+ pct pure, mesh size -80, from J. Bishop Co., Malvern,

Jan 1, 1964

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.&apos; Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By L. Weaver

THE Tennessee Copper Co.&apos;s mines are in the southeast corner of the state of Tennessee. Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails. The shaft is 12 ft 7 1/2 in. ID of the concrete walls. This is large enough for two 10-ton hoisting skips and a ladder compartment. One of the skip compartments is for hauling equipment. The grouting equipment was a 2%xlO-in. Gardner-Denver grout pump, air powered and developing 1000 lb pressure. A grout mixer, also air driven, fed the mixed solution into a tank coupled to the pump suction. Grout materials used were mostly water and Portland cement. Some Bentonite was used to seal porous ground near the surface.

Jan 11, 1950

THE Institute met on Wednesday evening, May 22d, in the parlor of the Stanton House, Dr. T. Sterry Hunt, President, in the chair. The President delivered an introductory address on the Brown Hematite Deposits of the Great Valley, after which the following papers were read and discussed : Note on the Result of an Experiment with the Wheeler Process of Combining Iron and Steel in the Head of a Rail, by W. E. C. Coxe, of Reading, Pa. On the Jenks Corundum Mine, Macon County, N. C., by Dr. R. W. Raymond, of New York City. On Wednesday afternoon, previous to the opening session, the members who had already arrived in Chattanooga, were taken by the Local Committee to the works of the Roane Iron Company, and Chattanooga Iron Company, and then to the top of Lookout Mountain, where, at the request of the members present, Dr. Hunt described the geological and geographical features of the Chattanooga region, with the magnificent panorama spread out before them as a map. On Thursday morning an excursion was made by steamboat down the Tennessee River as far as Shellmound. Here cars were taken to the coal mines of the Dade Coal Company, where the members were courteously received by Mr. E. B. Wells, the Superintendent. After a trip through the mines the party partook of a collation provided by the company. South Pittsburgh, on the Tennessee River, was next visited, where the Southern States Coal, Iron and Land Company have a large blast-furnace plant in the course of erection. After conducting the party through the works, shops, etc., Mr. James Bowron, the manager, entertained the members with graceful hospitality at dinner. The second session was held on Thursday evening for the transaction of business. The President, Dr. T. Sterry Hunt, appointed Messrs. W. E. C. Coxe, R. H. Richards, and F. J. Slade, scrutineers, to examine the ballots for officers for the ensuing year.

Jan 1, 1879

By Messervey, J. P.

NOVA SCOTIA is sharing in the rapid advance of the mining industry that is one of the remark- able features of Canada&apos;s recent progress. The production of coal and gypsum has increased rapidly, and there has also been a marked development in the mining of gold, salt, zinc, copper and other minerals. Coal, the basis of the principal mining industry in the Province, was discovered by the early explorers on the shore of Cape Breton Island, and used by the garrison at Halifax as early as 1749. The first government record shows total annual sales amounting to 1668 long tons in the year 1785, while last year production was 6,643,000 long tons. The principal mines are discussed in a separate paper by Alexander L. Hay1.

Jan 1, 1928

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By Sweetser, Ralph A

AT the fall meeting of the Iron and Steel Division, Oct. 4, 1934, in New York, a symposium was held on Slag Control in the Making of Iron and Steel. The chairman was J. H. Nead and the vice chairman, G. B. Waterhouse. The latter presided at both morning and afternoon sessions. The papers and discussions were presented in the order in which they appear on the following pages. To meet space requirements, much of this material has been considerably condensed. CONTENTS Slag Control and the Blast Furnace. By Ralph H. Sweetser. (With dis¬ cussion.) I Slag Control in Rimming Steel. By L. F. Reinartz 5 Slag Control Applied to Low-carbon Steel. By Frank G. Norris 9 Discussion on both papers 11 Slag Control for Basic Open-hearth High-carbon Steel. By W. J. Reagan. (With discussion.) 14 Slag Control for Recarburized Rail Steel. By A. P. Miller and T. S. Washburn. (With discussion.) 18 Slag Control for Alloy Forging Steel. By A. L. Feild. (With discussion.). . . 24 Slag Control for Alloy Forging Steel. By R. C. Good 27 Slag Control in Acid Open-hearth Steel. By Francis B. Foley. (With dis¬cussion.) 29 Slag Control for Basic Electric-furnace Steel. By H. F. Walther. (With discussion.) 31 Physical Testing of Slag. By A. B. Kinzel. . 40 General Discussion 41

Jan 1, 1935

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,&apos; solid-state sintering,&apos; thermal etching of grain boundaries, heats of solution and fine powders,&apos;1 grain-growth phenomena,&apos; the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,&apos; and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,&apos;2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.&apos;g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a &apos;&apos;pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation&apos;s No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i&apos;s the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company&apos;s Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones&apos; No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation&apos;s No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21&apos; A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc&apos;tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944