Search Documents

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Osvaldo Guilherme Comineli

While the hot cracking of Cu-containing steels is a serious and widely known problem for the industry, the literature reports that copper only slightly impairs the hot-ductility measured in laboratory. A distinction is drawn between hot ductility and hot shortness and the respective cracking operating mechanism involved at the respective range of temperature. The representability of the laboratory assessment of hot cracking of Cu-containing steels by hot tensile tests compared with actual results in industrial practice is discussed. The effectiveness of the variable affecting in each cracking mechanism and respective temperature range, focused in improving the hot cracking assessment of Cu-steels and the relative importance of oxidation will also be discussed. It is concluded that the hot tensile test in argon might be a good simulation if properly interpreted and that the role of oxidation is secondary in causing hot shortness. A schematic diagram for the hot tensile test is proposed.

Oct 30, 2017

By Maycon de Almeida Gomes

Fiber reinforced polymeric composites have received widespread attention in the past four decades because of their high specific strength and modulus. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites (2-3). Among various natural fibers, pineapple leaf fibers exhibit excellent mechanical properties. The main chemical constituents of pineapple fibers are cellulose (70–82%), lignin (5- 12%) and ash (1.1%). The superior mechanical properties of pineapple leaf fibers are associated with their high cellulose content (6). This work aims to make the analysis of the Izod impact energy against volume fraction of palf fibers of epoxy composites reinforced with PALF. The fibers were incorporated into the epoxy matrix with volume fraction from 0 to 30%. After fracture the specimens were macro photograph analyzed.

Aug 16, 2017

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By William Sergio Flores Roman

Los aceros para armaduras de hormigón tienen que exhibir una buena relación entre resistencia y tenacidad que se ve reflejado en la performance del producto en servicio al ser aplicado a esfuerzos exigidos. Acerbrag es una empresa que produce aceros para la industria de la construcción teniendo en su gama los aceros de medio carbono para la fabricación de barras conformadas de dureza natural para armaduras en estructuras de hormigón. El objetivo de este trabajo es encontrar criterios de ventanas de trabajos operacionales y de control para la manufactura de aceros con buenas propiedades mecánicas en términos de resistencia y tenacidad. Este paper muestra los resultados de los trabajos realizados en las diferentes áreas productivas para conseguir un producto final con mayor resistencia a altas exigencias en servicio, además, reporta diferentes aspectos del proceso de manufactura del producto que van desde el ajuste de la composición química del acero, incluyendo criterios de propiedades mecánicas objetivos, criterios de calidad interna mostrando la microestructura de la barra antes y después de los cambios y finalmente la calidad dimensional y superficial de la barra nervurada, este último potenciando la falla prematura del material. Todos estos cambios, se ven reflejados finalmente en la performance de la barra, sometida a los nuevos criterios de exigencia en los ensayos mecánicos.

Oct 30, 2017

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Bruno Kneipel Neto, Mylena Inaiê Correia, Fabricio Cerqueira, José Francisco da Silva Filho

The automotive industry, when aiming to increase the resistance to corrosion, uses in the Body in White (BIW) concept the galvanized steels. The hot-dip galvanized steels that stand out most are known as GI steels. They are formed by the zinc element and by phases of intermetallic intermediate iron-aluminum-zinc compounds. The characteristic properties of the GI coating are directly related to the formation of the intermetallic layer, which is responsible for providing the connection between the metal substrate and the coating layer. In this context, two different types of steel (SAE1005 and TRIP780 steel) were used for laboratory characterization of their intermetallic layers through metallographic techniques. The results of the tests showed that the inclined section metallographic inlay technique allows obtaining a larger region of analysis of the intermetallic layer. For the surface analysis, it was observed that the chemical solution used in the preparation of the samples was effective, making possible an analysis more specific about the intermetallic layer formation, distribution and morphology.

Oct 12, 2019

By Beatriz Dogliani, Elisabeth Williams, Maria Berenice Sandobal, Carina Bertino

The environmental management of steel mill slag should be understood as a management philosophy, observing technical, economic and environmental criteria associated with their generation, storage and final destination. The slag can be considered as a synthetic mineral resource and become a very useful co-product in different areas. The Argentinean steel industry prioritizes the efficient environmental management of its waste, thus contributing to its own survival taking into account the sustainable development. In the world, the slag produced by the steel industry has been used as steel aggregate for road bases, railway ballast and filling material among others. Any factor that influences the economy of the country affects all branches of society, mainly public agencies, whose financial resources are increasingly scarce to deal with all public works. It is necessary to join efforts of private and public initiative in the adoption of alternative materials that replace the use of finite natural resources. This presentation aims to show the work done by private companies together with public bodies and universities to obtain a regulatory document for the management of slag as steel aggregates for three different uses, namely: road use, railway use and general use.

Nov 5, 2019

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Wolfgang Kern

More and more coke oven plants worldwide face the task to improve their emission reduction at their coke oven batteries. In the 90’s PROven® was invented and developed by DMT to regulate the inner pressure of a single coke oven chamber. Generally, most of the coke oven chambers can only close and open their connection to the collecting main but without the possibility to regulate the pressure during the carbonization time. Through the installation of PROven® the load on the coke oven door sealing system and the charging lids will be decreased and so does the emissions of crude COG as well. The current PROven® system, installed in the collecting main, does not only regulate the chamber pressure, it replaces the valve between the goose neck and the collecting main, too. This variable pressure control allows decreasing the leakages at the emissions sources to a minimum and allows operating the collecting main under optimum pressure. Subsequently, this will lead to enhanced emission reduction. PROven® proved its value with more than 2,100 units installed by licensee worldwide. Nevertheless, DMT is always focused on its client’s needs and therefore enhance PROven® to provide the Best Available Technique (BAT). Among the main features of the now available system is the plain arrangement with a higher reliability and the possibility to install the system outside of the collecting main without modifying it. Hence, upgrading coke oven plants during operation is possible without any noticeable impact on the plant operation.

Aug 1, 2018

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Maycon Athayde

Samarco produces high quality iron ore pellets processed in straight grate furnaces. This process is essential in order to obtain adequate mechanical strength to the pellet transportation and operation in the reduction reactors. All mechanical properties of the agglomerates are obtained during the stage of firing where the slag and sintering bond happens, thus it is a decisive step to improve the pellet quality. Therefore, the velocity distribution of gas flow within this zone must have homogeneous and even velocity distribution. Hence, it was developed a mathematical CFD model to characterize the gas flow in the burning zone, applying the equations of conservation of momentum, mass and energy and an uneven flow distribution was identified and the gas velocity analyzed and validated through experimental data. On the other hand, on the present paper, an improved firing zone burner were developed and industrially implemented in a way to mitigate the uneven flow pattern detected aided by CFD. Different burner designs, based on CFD analysis, were experimented in order to succeed on the aggressive condition. The combustion was investigated and burner efficiency evaluated and compared with the simulation purposed.

Aug 2, 2018

By Edgar Ivan Castro Cedeño

En la producción de aceros limpios el control inclusionario es crítico para la obtención de un producto que cumpla con los requerimientos de calidad. El análisis de la distribución de tamaño de inclusión mediante modelos estadísticos permite estimar la incidencia de inclusiones en el producto solidificado a partir de mediciones tomadas en muestras relativamente pequeñas. En seis coladas de acero bajo carbono desoxidado con aluminio se tomaron muestras de acero a lo largo del procesamiento en horno olla y colada continua. Las muestras se prepararon para estimar mediante análisis metalográfico los tamaños de inclusión. Los datos de tamaño de inclusión se analizaron mediante modelos estadísticos de valores extremos, se hace una comparativa entre la distribución Gumbel (que forma parte de la norma ASTM E-2283) y la distribución Generalizada de Valores Extremos (GEV). Mediante una prueba de hipótesis con el estadístico Anderson-Darling, análisis de cuantiles y con la función de supervivencia se demuestra que la población inclusionaria se describe de una mejor manera con la distribución GEV. Finalmente se da un estimado de la incidencia probable de inclusiones en el producto solidificado.

Aug 16, 2017

By Rodrigo Ribeiro de Andrade, Túlio César Nogueira, Ed Juarez Mendes Taiss, Nilton José Lucinda de Oliveira

The objective of this study was to determine the effects of an eventual slab central macro-segregation in microalloyed steels with low Mn content (0.80%) and high Nb content (0.08 to 0.10%) on the kinetics of recrystallization of austenite during its rolling, on its critical temperatures, that is, of non-recrystallization (Tnr), start Ar3 and finish Ar1 of ferrite transformation and its response to a simulated industrial thermomechanical processing. The determination of the austenite recrystallization kinetics was made through isothermal double compression tests using a dilatometer, while the critical temperatures were determined through hot torsion tests in a Gleeble® 3800. It was found that austenite recrystallization kinetics, Ar3 and Ar1 temperatures did not present significant changes for the samples extracted both at ¼ of the thickness and at the core of the plate, indicating that, as expected, the central segregation in this type of steel was not intense to the point of affecting this phenomenon. The Tnr values determined for the samples extracted in the core of the plate were, on average, 30°C lower than those obtained from specimens extracted at ¼ thickness, which suggests that a significant portion of the carbonitrides present in the core of the slab are eutectic and coarse, not having completely dissolved during the reheating of the specimens. This occurred despite the fact that the austenitization temperature adopted in this treatment theoretically leads to the total dissolution of Nb, as seems to have occurred in the case of specimens extracted at ¼ of thickness, where carbonitrides have a finer size.

Oct 1, 2019

By Michel Rodrigo Luiz, Glaudistoni da Silva Félix, Osmar Duarte Junior

This article deals with a project to reduce the preparation time and threading the coils in the input section of a pickling line coupled to the cold strip mill (PLTCM) at ArcelorMittal Vega. The project developed serves for the detection and elimination of bottlenecks in the input section. The project was conceived by the philosophy of the Theory of Constraints (TOC) and Lean Six Sigma (6 sigma), here seen as sequencing serial / parallel in the preparation and threading the coils. In this context, a proposal to modify the automatic sequencing and reduction of interruptions due to failure of the automation / equipment confirmed its effectiveness reducing the total time preparation time and threading the coils in the entry section by 15%. This project was developed without investment costs, bringing gains on the order of US$613,769.00.

Oct 1, 2019

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Silvio Cecchini

State-of-the Art Mould Level Control Solutions for continuous casting applications face different challenges. On the one hand, technological phenomena such as clogging and unclogging, unsteady bulging or waving can create unpredicted meniscus disturbances by completely changing the casting channel geometry and the flow behaviour of liquid steel to the mould. On the other hand, from the viewpoint of caster operations, long lifetime, quick interchange-ability and integration capability into existing systems must be achieved. In the present contribution, the overall development of INTECO TBR’s mould level master – a comprehensive mould level control solution for all continuous casting applications – will be introduced. The basis for the presented system is a development over several years which includes investigations of all critical components such as shroud, stopper, stopper mechanism, servo actuator and mould level control program. These investigations finally resulted in a new-ly developed control algorithm for a highly dynamic servo actuator. The control algorithm with its basic functionality such as the prevention, identification and removal of clogging impacts with the associated automation functions to reduce their influence onto the overall mould level control performance will be presented. The scientific basis, the resulting control functions and their related automation implementation will also be illustrated. Finally, a patented control algorithm and control functionality for unsteady bulging and waving effects with the associated automation functions to reduce their influence onto the overall mould level control performance.

Aug 16, 2017