Search Documents

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017

By Leonardo Lúcio de Araújo Gouveia

Este trabalho objetiva o estudo da influência da adição de fibras vegetais de bambu e cana-de-açúcar nas propriedades mecânicas do concreto. Para este trabalho foram confeccionados corpos-de-prova cilíndricos e prismáticos nos quais foram adicionados 2% e 5% em volume das fibras à massa do concreto. Após a cura, conforme NBR 5738 (2003) [1], os mesmos foram testados via ensaios de resistência à compressão conforme NBR 5739 (2007) [2], resistência à tração por compressão diametral, conforme NBR 7222 (2011) [3], resistência à tração na flexão conforme NBR 12142 (2010) [4] e módulo de elasticidade estático, conforme NBR 8522(2008) [5]. Verificou-se após os testes que todos os concretos produzidos atenderam a resistência mínima a compressão de 20 MPa, recomendado pela NBR 6118 (2003) [6] para fins estruturais. Foi observado um aumento da resistência à compressão em relação à mistura padrão. O concreto com adição de fibras de bambu apresentou melhor resistência mecânica em relação ao concreto com adição das fibras de cana-de-açúcar e ao concreto sem adição.

Aug 7, 2018

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Leandro Augusto Viana Teixeira, Márcio Francisco Dill Junges, Adauto Caldara

Innovation in the mining industry is critical when facing ever growing challenges, like the need to increase safety, reduce social and environmental impact, deal with commodities price fluctuations among others. However, successful innovation is not only the product of technological innovation, but it is also dependent on Innovation Management, which consists of changing the way a company fosters innovation, creating a new structure able to leverage technology knowledge and the ability to convert this knowledge in value. This paper presents a restructure option for innovation that focus on R&D development linked to business needs and company strategy. This new system was approached based on four fundamental blocks for innovation management (Approach, Organization, Resources and Metrics), showing how the technology master plan and a management tool are able to bring together all aspects necessary for the proper operation of the system. The new system confirmed the importance of having the initiatives organized as innovation roadmaps, connecting techno-scientific development with the company needs through the use of KPIs that are relevant to the business.

Oct 3, 2019

By Lucas Gonçalves Generoso, Larissa Rodrigues de Carvalho Rocha, Mauro Vivaldino Fernandes, Gustavo Serrano dos Santos, Gustavo Alexandre da Costa Manso

O Alto-Forno 3 da Usiminas iniciou sua atual campanha em 1999. Projetada para durar 15 anos de operação, previa-se uma produção de 41 Mt de gusa. A partir de 2008, iniciaram as avarias mais significativas no sistema de refrigeração, possibilitando a entrada de água e os consequentes distúrbios operacionais. Buscando estender a atual campanha até 2021, a Usiminas realizou, dentre outras atividades de preservação, duas trocas de staves, em 2015 e 2018. Neste trabalho, são apresentados o planejamento e os principais procedimentos relacionados à parada operacional do alto-forno para a segunda troca de staves, com foco nas atividades operacionais que permitiram a redução do nível da carga até 25,1 metros em relação ao stock line. Destacam-se os cuidados e o êxito no abaixamento de carga até o nível das ventaneiras e a metodologia de troca de staves adotada. Por fim, a previsão de extensão da campanha em 7 anos, possibilitará atingir uma produção acumulada de 53,5 Mt, superando em 12,5 Mt o valor projetado.

Oct 1, 2019

By Santiago Faucher

Molten slag from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of thermal energy. But the common slag dumping and water granulation methods used for slag treatment do not permit energy recovery. Furthermore, water is present in these processes and while operations are designed to minimize risks of steam explosions, from the contact of slag with water, these common slag handling practices have never been inherently safe. Common handling practices do permit some slags to be sold, but often in low volumes at low prices. Dry granulation offers advantages over these common slag handling practices, including the production of by-products, the recovery of thermal energy, and the eliminated consumption and safety hazards of water. For these reasons, there have been various studies in dry granulation and heat recovery, but most have never been brought to commercial scale due to scalability and cost challenges. Ecomaister- Hatch has developed and brought to commercial scale a reliable and simple dry granulation and heat recovery technology. Here we review common slag handling practices, the developments in dry slag granulation over the last three decades, introduce the Ecomaister-Hatch dry slag granulation process, and elaborate on future applications of the technology in the processing of argon oxygen decarburization and blast furnace slags.

Aug 17, 2017

By Milan Terčelj, Matej Drobne, Urška Klančnik, Peter Fajfar

The study of oxidation behavior of High Chromium Steel material used for surface layer of work rolls was carried out. Specimens taken directly from the roll were subjected to thermal fatigue in the temperature range between room temperature and 500 °C up to 700 °C by using thermo-mechanical simulator Gleeble 1500D. Our observation was focused on the impact of oxidation as a principal mechanism of degradation of the roll’s surface layer - mainly on the characteristics of oxidation propagation in relation to the test temperature and microstructure constituents characteristics of the material. Oxidation is considerably accelerated by certain characteristics of eutectic and primary carbides, i.e. their size (area), composition, morphology, orientation regarding to the water-cooled surface, etc. In the presented paper selected cases where emphasized oxidation takes place are investigated, analyzed and explained. Obtained results thus represent a contribution to explanation of conditions which lead to acceleration of oxidation behavior that in turn can lead to chipping or even early spalling of material from the roll surface layer.

Oct 1, 2019

By Mário César Mantovani

The steel for gas turbine compressor discs (26NiCrMoV14.5) requires some mechanical properties like strength, impact, toughness, fatigue, and creep resistance in order to be used in such application. To achieve the properties required for the gas turbine compressor discs, the material should have very low contents of sulfur, phosphorus, antimony, tin and arsenic. The level of cleanliness should also be very high and this is possible by achieving low oxygen content keeping the deoxidation elements like silicon, manganese and even the aluminum in very low percentages. The main problem in refining such steel is to adjust a sufficiently low oxygen content to have a good desulfurization and at same time a good cleanliness without using silicon, manganese or aluminum as deoxidizers. Combination of initial selection material, steelmaking process control, forging sequence and heat treatment cycles can provide uniform mechanical properties throughout the gas turbine compressor discs. Villares Metals SA as a big player on special steels with complex process has been developing this kind of material for several years. The objective of this work is to show the process technology evolution involved in the production of this kind of steel under the discussed preconditions.

Aug 17, 2017

By Paula Maria Gomes Cunha Leão, Flávio de Castro Dutra, Fabrício Vilela Parreira, Silvio Maranha

In the iron ore beneficiation, tailings are inherent in the concentration processes to which the ores are subjected for the production of commercial products. The large generation of tailings has been motivating the study of technological alternatives for its reuse, with the development of processes that contemplate the concentration of fine ore particles present in the tailings, such as the reintroduction of these particles in the process of manufacture of the iron and steel itself, through the agglomeration techniques such as briquetting. The aim of this article is to study the technical feasibility of the production of iron ore tailings and coking coal briquettes for use in reduction reactors, through a systematic review of the literature on agglomeration, briquetting and self-reduction processes, covering the main variables that influence the production of high quality briquettes, such as binders use, binder behavior of coking coal, coal granulometry, iron ore and coal proportion, compacting pressure and temperature of thermal treatment and the effects of these variables on briquettes final properties.

Oct 1, 2019

By Claude Gaspard, Stefan Wahlund, Daniel Cavalier

A point of great importance in the cold rolling process for automotive sheet is the cleanliness of the strip, particularly critical in case of batch annealing with no degreasing line or inefficient cleaning before continuous lines. In this specific cases, pollution of the strip surface could be prohibitive when rolling in the early stands of tandem mill with conventional forged work rolls as ground. The strip cleanliness strongly deteriorates during rolling particularly with high roughness rolls: iron fines are generated at the strip surface due to friction and stick on the sheet. It is well known that chrome plating on ground forged rolls in the early stands improve the strip cleanliness. This paper summarizes the results of 3D surface roughness topography studies on forged work rolls, with and without chrome plating, combined with sheet cleanliness measurement during rolling. It shows that a well determined topography has to be obtained on the work rolls used in early stands in order to roll in the mixed lubrication regime, as described by the Stribeck curve, minimizing the friction coefficient and therefore optimizing the cleanliness of the rolled sheet. The main roll roughness parameters to take into account for that purpose are the roughness level Sa, and even more, the Kurtosis parameters Sk, Spk, Svk and Ssk. The ideal surface morphology promotes deep valleys to the detriment of peaks, leading to a roll surface capable of retaining/trapping oil in the valleys, while peaks are minimized, thus reducing the friction in the roll bite and the amount of iron fines produced. To achieve this objective, new grinding wheel technologies are currently developed, in dialogue with wheel manufacturers, to create such ideal morphology of roughness well adapted to HSS forged rolls.

Oct 1, 2019

By Adriana Amaro Diacenco

Neste trabalho, os procedimentos para modelagem de estruturas de compósitos do tipo sanduíche que incorporam materiais viscoelásticos são apresentados. A análise numérica foi desenvolvida utilizando a Teoria de Deformação Cisalhante de Primeira Ordem (FSDT), que é implementada em um elemento Serendipity retangular contendo oito nós e cinco graus de liberdade. A incorporação do amortecimento para os modelos de elementos finitos em compósitos de placas laminadas é feita usando a abordagem de módulo complexo e a resolução numérica das equações resultantes do movimento são aspectos particularmente relevantes dos procedimentos de modelagem. Após as discussões de vários aspectos teóricos, as funções de resposta em frequências (FRF's) são calculadas para placas laminadas de compósitos com camada viscoelástica.

Aug 17, 2017

By Ana Maria Gontijo Figueiredo

Muitos dispositivos biomecânicos têm sido produzidos com ligas superelásticas (SE) de NiTi. Na maioria das aplicações, o material é submetido a solicitações mecânicas cíclicas, tornando seu comportamento sob fadiga um parâmetro importante. Neste trabalho são apresentados resultados de ensaios de fadiga por flexão rotativa de um fio SE, ensaiado a seis temperaturas diferentes, sob amplitudes de deformação (?a) variando de 1% a 12%. As curvas mostram que a vida em fadiga do material na fase martensítica estável (ME) é cerca de 100x maior do que na fase austenítica estável (AE). A curva do fio SE se aproxima da curva do fio AE para pequenas ?a e, com o seu aumento, se aproxima da curva do fio ME quando ?a aumenta. As superfícies de fratura obtidas foram observadas ao microscópio eletrônico de varredura e foram calculadas as áreas correspondentes à fratura por fadiga (af). Os resultados mostram que, para o fio nas fases AE e ME, af decresce continuamente com o aumento da ?a. Para o caso do fio SE, af permanece relativamente constante para valores intermediários de amplitude de deformação (2% a 8%). Para uma mesma deformação, af cresce com a redução da temperatura, com o consequente aumento do número de ciclos para falha.

Aug 8, 2018

By Armando Vazquez

Steel Dynamics Inc. (SDI) and Tenova Goodfellow Inc. (TGI) have successfully commissioned the first hybrid extractive/laser system for continuous and full spectrum analysis (CO, CO2, O2, H2 and H2O vapor) on two twin shell furnaces at Butler, Indiana. NextGen® technology using off-gas analysis as a main tool for EAF practice optimization is a proven effective method for improving plant productivity. Significant benefits attributed to the NextGen® system are operational cost reductions through the use of real-time dynamic control of chemical energy and improved environmental conditions through reduced GHG emissions. Additionally, the implementation of Tenova’s Water Leak Detection Technology® has shown results as an effective tool for operators to identify in real-time the presence of water during both reducing and oxidizing conditions. This paper will include project details, trials and results and will also outline the latest hardware developments and multipoint capabilities

Oct 30, 2017

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Jorge Madias

A Aceros Arequipa é a maior siderúrgica do Peru. A empresa opera uma planta em Pisco, com uma aciaria para 850.000 t anuais de aço líquido, e uma capacidade de laminação de 1.250.000 t anuais de produtos longos. Um projeto de integração vertical incluindo coqueria non-recovery, sinterização e alto-forno foi considerado. Como parte do projeto, um forno piloto de coqueificação foi instalado, com o intuito de testar carvões próprios e importados e obter a máxima participação de carvão local nas misturas. Foram testados sez carvões peruanos e antracito. Os carvões importados escolhidos foram três da Colômbia e quatro dos Estados Unidos. Levando em conta as baixas propriedades dos carvões próprios, foi introduzida a estampagem da carga. A máxima participação dos carvões locais, mantendo a qualidade requerida, foi obtida com 80% de carvão peruano, e 20% de um carvão columbiano. Pode-se usar até 10% de antracito, junto a 60% de carvão peruano e 30% de carvão colombiano.

Oct 30, 2017

By Hugo Leandro Rosa

A CBMM aplicou aços micro ligados ao nióbio em dois tipos de caçambas de carregadeiras de rodas que operam na usina de Araxá, Brasil. O objetivo foi avaliar os benefícios destes aços relacionados com redução dos custos, aumento da produtividade e vida útil dos componentes. Uma das máquinas analisadas coleta peças quentes de ferro nióbio para carregamento dos silos do britador. O uso de um aço ferramenta de alta resistência e resistente ao desgaste solucionou os problemas de deformação, desgaste e rachaduras durante o serviço, aumentando a vida útil da caçamba em cerca de 190%. A outra máquina avaliada foi uma carregadeira de rodas que opera na mina de minério de nióbio. O novo desenho com aços de alta resistência mecânica e resistente ao desgaste reduziu o peso em 14%, correspondendo ao incremento na capacidade de carga. A carga extra possibilitou um aumento na produtividade dos caminhões de 42 toneladas. Com os novos materiais, as trincas anteriormente encontradas na caçamba da pá carregadeira foram eliminadas, enquanto foi mantida a resistência ao desgaste antes oferecida pelo aço revestido com carbeto de cromo reduzindo também os custos de investimento em 7%.

Aug 17, 2017

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Eric Schaub

Hot Blast Stove Systems are an important equipment of a Blast Furnace plant. During the last years, performance requirements and operation practice for the Hot Blast Systems have changed and have a big influence on the Blast Furnace operation. Therefore it is necessary to keep the Hot Blast System in proper condition in order to maintain the production capacity of the Blast Furnace. It is important for operators to know the condition and relevant constrains of a Hot Blast Stove Plant. Assessing its condition on a regular basis, especially in advance of a Blast Furnace relining is therefore advisable. Considering the individual condition of the Hot Blast Stove Plant, improvements in operation, but also specific and dedicated repairs might be implemented. Design improvements can be implemented as well during such repairs. This paper will describe some of these design improvements, will illustrate their implementation in new hot blast stoves but will also describe repair methods for existing stoves. In addition new developments became popular during the last decade, like the so called Dome Combustion Stoves, which was invented already 30 years ago in Western Europe. Paul Wurth’s development in this regard will be discussed in this paper as well.

Oct 30, 2017

By Bruna Iost Camacho

Inclusões não metálicas são impurezas presentes nos aços que corrompem, quando não moderadas, suas propriedades mecânicas e metalúrgicas. O tratamento de inclusões com ligas à base de cálcio é fortemente utilizado visando à produção de aços mais limpos e é fortemente induzido pela composição química e temperatura do aço. O objetivo geral deste trabalho será o estudo termodinâmico e experimental a respeito da modificação de inclusões não metálicas através do tratamento com cálcio, em aços de diferentes teores de enxofre. O presente trabalho utilizará como metodologia: i) obtenção de dados através de experimentos em forno resistivo para determinar os dados iniciais utilizados nas simulações; ii) estudo termodinâmico computacional através do software FactSage; iii) análise de inclusões via MEV/EDS e ASPEX-PSEM explorer. iv) comparação dos resultados obtidos nos dois meios de análise e também compará-las com os resultados obtidos via simulação. Para tanto, serão estabelecidas dife rentes temperaturas e concentrações de cálcio no banho e diferentes tempos de processo. Como resultado final, espera-se gerar um maior conhecimento que contribua para a compreensão dos fenômenos envolvidos em aços com maior teor de enxofre. Além disso, espera-se validar as técnicas e metodologia empregadas neste trabalho.

Aug 8, 2018

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018