Search Documents

By Keuncheol Choi, Yonghack Lee

"The new lead smelter based on the QSL technology was started operation from May 1992 at Onsan Refinery of Korea Zinc Co., Ltd. The smelter is designed to treat not only various types of lead concentrate but also secondary materials coming from the zinc plant without special pretreatment.Shortly after the start-up of the operation, it has demonstrated that the smelter have a capability to treat wide range of raw materials. Continuous modifications and improvements of the plant are still under way to increase the feed rate and also the ratio of secondary materials to the feed.In this paper, the operating experience and results of QSL smelter, especially the injection of gases and coal to the melt, will be presented with major operation parameters and data.INTRODUCTIONThe QSL lead smelter based on new injection technology was commissioned at the Korea Zinc's Onsan plant from May of 1992. After starting the operation, the QSL lead smelter faced various kinds of mechanical and metallurgical troubles. However, these were gradually worked out by the continuous improvements and efforts.At present, the QSL lead smelter is operated stably at the total feed rate of 57 tonnes per hour with an increased amount of secondary materials."

Jan 1, 1996

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999

By G. H. Khoe

Although some hydrometallurgical process liquors contain significant amounts of ferrous and arsenate ions, no reliable thermochemical data for the aqueous complexes and the solubility of the ferrous arsenate precipitate are available. The complexation of iron(11) with arsenate has been investigated using the potentiomemc titration method. The results indicated that virtually no complexation of iron(@ with arsenate has been observed. This is in contrast to the significant complexing reported for iron(1n) with arsenate. The solubility product of the precipitate was calculated using the concentrations of appropriate arsenate species pertaining to the observed precipitation pH's. The fit of the observed precipitation points on the solubility curve of the computed stability diagram was used to assess the appropriateness of the equilibrium model.

Jan 1, 1991

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By T. Shibasaki, S. Kamio, K. Kanamori

"Mitsubishi Process has been proven through fifteen years operation to be highly productive, cost efficient and easy to abate environmental requirements. However, in order the process to remain competitive from now on, it should also be adaptable to a variety of varying conditions. Various test works have been conducted from such a stand point of view and some of the new concepts have been implemented to the actual operation.The paper discusses the adaptability of the process to the change of concentrate grade with respect to copper and also impurities, acceptability of the secondary materials and the potential to increase unit capacity. IntroductionThe first commercial plant of Mitsubishi Process with 48,000 mt copper annual capacity started its operation at Naoshima Smelter of Mitsubishi Metal Corporation in 1974, and the second plant with 65,000 st annual capacity started in 1981, at Kidd Smelter, Timmins, Ontario, now Kidd Creek Division of Falconbridge Limited 2. These plants have increased their capacities to 90,000 mtpa respectively by adding oxygen and acid plant capacities while maintaining the original furnace design uncharged. Thereby both smelters have established more cost efficient operations. (3), (4)Mitsubishi Process applies so-called multi-furnace continuous system. Figure 1 shows conceptual flowsheet. Backgrounds that required and justified the development of such system are as follows:"

Jan 1, 1988

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By J. L. Sanchez

Using a special double-zone transpiration reactor, the vapor transport chemistry of vanadium pentoxide in the presence of water vapor has been investigated. Three possible volatile hydroxides above V,O,(s) are reported in the literature: VO,(OH),, V,O,(OH),, and VO(OH),. In the present study, it was established that VO(OH), is the principal gaseous hydroxide species formed. The predominant reaction was found to be: { } The vapor pressure of VO(OH), was measured as a function of temperature, water pressure, oxygen pressure and flowrate. The results have been used to determine the Gibbs free energy of the above reaction as a function of temperature: { } The results of the present work were combined with thermodynamic data reported in the literature to obtain expressions for the AGO for the reaction above V,0,(1) and the AGO of formation (units in cal/g-mole).

Jan 1, 1993

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior of TiO2 nanoparticles was thermogravimetically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanoparticles, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500 °C at heating rate of 1O 'Cumin. The weight increase curve showed a maximum of ca 30 wt% at around 750 T and then gradually decreased to ca 12w% at 1000OC. This would be caused by the formation of TiS2 followed by the decomposition of TiS2 to lower sulfides, such as Til.08S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanpparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By H. K. Lin

Pyrite oxidation in chloride solutions was investigated with cyclic voltammetry, ac impedance and potential step techniques. The pyrite oxidation in quiescent electrolytes is irreversible and controlled by diffusion. Depression of the semi-circle in the complex plane plot has been explained mathematically based on the concept of the equivalent circuit. When the semi-circle is depressed, the mathematical formula indicates that the reaction resistance should be obtained from the intersection of the semi-circle with Z-axis instead of the semi- circle diameter. The peak charging current densities at 1.10 and 0.90 V vs. SHE obtained from the equivalent circuit coupled with the ac impedance measurements match the peak current densities obtained with the potential step measurements.

Jan 1, 1997

By Xiaojie Gao, Shufeng Yang, Jingshe Li, Chengsong Liu

In the blast furnace process, the dust entrained in the blast furnace gas enters into the down-comer, flows through the gravity dust separator (to eliminate coarse particles) and then is collected in a bag-house. The powder collected by the baghouse is called bag dust, while both fractions are called blast furnace dust whose main components are C and Fe. The dust also contains small amounts of nonferrous metals such as Zn and Pb, which have some value. Also, due to the small particle size and low density the dust is easily suspended in air and so can endanger human health. Therefore it is necessary to develop a process to both treat the dust to recover the metal values and to dispose of the residue – preferably by recycling to the blast furnace itself via the sinter strand. These objectives will result in good economic, environmental and social benefits [1].

Jan 1, 2014

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By M. I. Novgorodova

Most of the gold in the earth's crust occurs as finely-dispersed gold and accounts for much of the gold lost in extraction processes and during exploration for gold. The Compositions, sizes, and morphology of fine gold particles (0.01 to 10 ~m in diameter) were studied with high resolution electron microscopy coupled with electron microprobe and microdiffraction devices, using colloidal carbon replicas. Correlations were made between fine gold, mineral associations and ore genesis. The results provide qualitative information on the proportions of finely dispersed, invisible and visible gold distribution in ores. Such knowledge is fundamental when planning an optimum technological recovery process.

Jan 1, 1991

By Asmo Vartiainen

The viscosity of liquid Fe-O-SiO2 -slag at copper smelting conditions was investigated using a rotational viscometer. The studied parameters were oxygen partial pressure (10" °-10"6 bar ); composition of slag (Fe/SiO2 ratio), and temperature (1250-1400°C). The viscosity values are presented as a function of Fe/SiO2 ratio and as isoviscosity curves in ternary FeO-Fe2O3-SiO2 diagrams. The increase in viscosity at high silica contents can be accounted for the polymerisation effect of SiO4/4- -anions. At high ferric iron contents, higher oxygen partial pressure, the viscosity values increase especially near the magnetite saturation. The viscosity values are highest at the double saturation of silica and magnetite. At lower silica and ferric iron contents the viscosity values are more uniform in the homogenous liquid slag area. The viscosity values were lowest at high temperatures and highest at low temperatures.

Jan 1, 1998

By Bingliang Gao, Junli Xu, Michal Korenko, Jinzhao Guan, Liangxing Li, Zhongning Shi, Zhaowen Wang, Aimin Liu

Al-Si alloy, a precursor of solar grade silicon, was prepared by direct electrolysis in cryolite molten salt at 950 oC using high purity silica as material, liquid aluminum as the cathode and high purity graphite as the anode. The electrochemical behavior of Si(IV) ion was investigated using cyclic voltammetry method. The electrolysis products were characterized by XRD, SEM/EDS and ICP. The results indicate that the reduction process of Si(IV) on tungsten electrode is a two-step process and there is about 0.6 V gap between the two steps. The contents of boron and phosphorus in the aluminum-silicon alloy are 3 ppmw and 8 ppmw, which will make the directional solidification purification effectively and reduce the cost of preparation solar grade silicon from metallurgical grade silicon.

Jan 1, 2015

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation's main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By Hideaki Tokuyarna

Recovery of metal such as V, Ni and Fe from oil fly ash is important for efficient use of natural resources and protection of environment. Leaching of metals from fly ash followed by ion exchange of leached metals has been examined to develop a process which can selectively recover V and Ni from the fly ash. Experiment of leaching with water, HCI, H2S04 and NaOH leads us to propose a two-step leaching process as an effective and mild operation. The first step is leaching with water for removal of Ni, Mg, A1 and Zn and the second step is leaching with acidic solution for the recovery of V. The metals V and Ni are then separated from other metals in each leached liquor by ion exchange. Advantage of this separation process is that acidic leachant can be reused, which contribute to save separation energy.

Jan 1, 2002

By Yong Zhao, Yan-hui Sun

Behaviors and evolutions of MgO·Al2O3 in non-oriented silicon steel during calcium treatment were investigated by thermodynamic calculations and high-temperature experiments. MgO·Al2O3 inclusions were the main type of inclusions before calcium treatment, which is also confirmed by the stability diagram of MgO/MgO·Al2O3/Al2O3 from thermodynamic calculations. After calcium treatment, the majority of original MgO·Al2O3 inclusions were mainly modified to CaO-MgO-Al2O3 system inclusions, this would be beneficial to improve castability and product quality of silicon steel. But there was no modification happening to some MgO·Al2O3 spinels which were directly surrounded by CaS inclusions. The content of Al2O3 occasionally existed a sudden increase besides a common decrease in the product layer of CaO·MgO·Al2O3. Then the evolution mechanisms of MgO·Al2O3 inclusions were proposed in present work. Thus, Al/Mg atom ratio had a significant influence on the modification of MgO·Al2O3 spinel.

Jan 1, 2016

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976