Search Documents

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth's crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974

By R. B. Lawrie

Diesel powered underground mining equipment is presently the most productive, safest and efficient equipment used in underground mining operations. The widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel missions with particulate traps and filters.

Jan 1, 1985

By Eugene E. Brucker

In recent years, there has been increased interest in construction problems presented by karst topography. Twenty-five years ago, karst areas were by-passed for development. Today, the high cost of land and population pressures are requiring utilization of karst areas. Areas exhibiting karst features can be satisfactorily developed so that construction can proceed in a normal manner; or the areas may be left undeveloped and the underground drainage system abused by improper use causing or contributing to structural collapse, excessive erosion, and a grave threat to the stability of land development and the environment. The term "karst" is a comprehensive term applied to areas underlain by soluble rock that possess a topography formed chiefly by the dissolving of rock and the diversion of surface waters to underground routes. There are four features which contribute to the maximum development of karst. 1. A soluble rock, preferably limestone, must be present at or near the surface of the ground. Occasionally, dolomite will suffice.

Jan 1, 1970

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By R. K. Mehta

Conventional triboelectrification based dry coal beneficiation methods require ground coal as a prerequisite feed material, energy intensive static-in-line mixer or cyclonic tribocharger configuration, and transport and/or improvement in the design of free-fall separators to improve the separation efficiency of [me pyrite/mineral matter from coal. The proposed paper illustrates the two concepts. First, the use of ceramic media in a polyurethane lined attitor in achieving simultaneous grinding and differential charging. Second, the use of an electrocentrifuge to selectively separate coal from mineral matter present in the triboelectrified mixture. It is of interest to note that some ceramic media can satisfy the requirements of both desired density and work function to achieve grinding and differential charging.

Jan 1, 1996

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum (Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coals cans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By S. C. Libby

The amount of fine material (minus 60 Tyler mesh) generated during calcination and/or handling of calcined abrasive grade bauxite from Alcoa's operations at Moengo, Suriname, has recently increased relative to past production experience. Bulk samples of raw abrasive grade bauxite from three deposits in the Moengo area have been studied in order to determine the factors controlling the generation of fine material samples from the Jones IC and Tapira deposits, which generate excessive amounts of fine material, have been compared with reference samples from the Begi Gado deposit, which does not generate excessive fine material. Additional type samples of abrasive grade and marginal abrasive grade bauxite from deposits in the Moengo area which represent different bauxite textures found in the Jones IC, Jones I, and Begi Gado deposits have also been studied. Field observations in the Moengo area have indicated that abrasive grade bauxites with a dull, earthy appearance generally do not generate excessive fines. On the other hand, excessive fines are generally associated with coarsely crystalline bauxite in which the gibbsite crystals appear to sparkle in sunlight.

Jan 1, 1980

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Stanley O. Reichert

At nuclear facilities, three types of radioactive waste must be managed: (1) high-level liquid waste containing fission products from the chemical separation of irradiated uranium, (2) low-level condensates from the concentration of the high-level waste, and (3) dry solids such as obsolete process equipment, spent ion exchange resins, and irradiated metal scrap. The geological and environmental characteristics of a site are important considerations in planning the waste management program. At the Savannah River Plant, low-level liquids and dry solids are safely and economically placed in the soil where the geologic and hydrologic conditions are favorable. Within the general area where the waste originates, studies are made to locate seepage basins and burial grounds in the most favorable sites: (1) soils should have a high ion exchange capacity and moderate to low permeability, (2) the water table should be deep, and (3) burial sites should be relatively distant from the nearest flowing stream.

Jan 1, 1968

By G. J. Allen

Kennecott Copper Corporation&apos;s Nevada Mines Division initiated a program to stabilize the inactive portions of the tailings disposal area and perimeter dikes in 1946. To date, approximately 1,000 acres have been stabilized with vegetation and ground cover.

Jan 1, 1978

By Shawna Von Stockhausen, Hong Yang, Tung T. Vu, Derek Penrice, Kevin Huynh

"The Regional Connector Transit Corridor is a 1.9 mile long light rail transit project in downtown Los Angeles, California. The project includes approximately 4,930 feet of twin bored tunnels together with a mined crossover cavern, 3 deep stations, and other cut-and-cover structures. The bored tunnels will be excavated using an earth pressure balance tunnel boring machine through Fernando Formation (extremely weak to weak rock) and alluvium. The tunneling will be performed in close proximity to a large number of existing structures, including the existing Metro Red Line tunnels with as little as 6 feet of separation. Thus, the evaluations of the tunneling effect on these structures and the instrumentation and monitoring program is an essential part of the project design. This paper provides a very brief overview of the considerations and evaluations of the tunneling effects on the existing structures and results of evaluation obtained during the final design stage of the project. INTRODUCTION The proposed Regional Connector Transit Corridor (RCTC) project provides a 1.9 mile-long connection between the Metro Gold Line from Pasadena and East Los Angeles; and the Metro Blue Line to Long Beach and the Expo Line to Culver City. The alignment is shown in Figure 1. The Regional Connector will provide new tracks through downtown Los Angeles. The project will extend underground from the Metro Blue, Expo, Red, and Purple Lines’ 7th Street/Metro Center Station following Flower Street, curving northeast to the north of 3rd Street under the 2nd Street Tunnel. The alignment will then continue eastward under 2nd Street, turning northeast to cross under the intersection of 1st and Alameda Streets, then splitting into two branches above the ground surface, one branch extending north along Alameda Street and the other extending east along 1st Street. The project elements include 3 deep stations, a SEM cavern, segments of TBM bored tunnels, and cut-and-cover guideway structures. The bored tunnels have an excavated diameter of 20.3 feet. The subsurface conditions along the tunnel alignment generally consist of artificial fill overlaying finer-grained alluvium (dominantly medium dense to dense sandy soils), underlain by coarser-grained alluvium (a wide variety of medium dense to dense sandy and gravely soils). Below the coarser-grained alluvium is Fernando Formation, which is characterized as extremely weak to very weak sedimentary bedrock. A long stretch of the alignment will be excavated in this formation. The soil layers above the Fernando Formation are of variable thickness and spatial distribution. The geologic profile is shown in Figure 2."

Jan 1, 2016