Search Documents

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By William G. Kegel

Apart from a usable product and good 'mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and- an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating shaft. In the case of a locomotive, this principle is used in dynamic braking. The momentum of the locomotive drives the motor and generates d-c power. The power is regulated with resistors and provides opposition to the motion of the locomotive.

Jan 1, 1981

By Gordon R. S. Smith

This paper is in two parts. The first part describes Membrane Back-Pulse Filtration and the effects of very short filter downtimes on cycle filtration rates. Part II describes the use of Membrane Back-Pulse Filtration for combined thickening and polishing soda ash thickener feed material followed by a description of computer modeling of CCD circuits by Iterative solver.

Jan 1, 1991

By G. Xu, A. R. Kumar, N. A. Amoah

Prolonged exposure to high concentrations of respirable coal mine dust causes coal workers’ pneumoconiosis and silicosis. Underground coal mine roof bolter operators are more prone to elevated exposure to coal and silica dust. The canopy air curtain (CAC) was developed by NIOSH to protect roof bolter operators from the exposure. The CAC supplies filtered air over the breathing zone of the operator. This dilutes the high coal dust concentrations and provides for an impenetrable air curtain. Many studies have been carried out to improve CAC efficiency. However, field test has shown variable dust control efficiencies indicating rooms to further improve due to the nonuniform airflow distribution across the plenum and ineffective perimeter flow. This study therefore redesigns the CAC with optimized flow distribution that effectively protects roof bolters from coal dust exposures. Computational fluid dynamics (CFD) simulations are used to optimize the uniformity of airflow distribution across the plenum to achieve the best possible uniformity. A lab experiment validates the CFD model and confirms the ability of this design to reduce floor dust pickup, prevent external wind infiltration, and offer an improved protection efficiency

Mar 2, 2022

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Strong earthquakes occur frequently in Japan, and some rock tunnels have sustained severe damages on their permanent lining. Many road tunnels, which were constructed by conventional steel arch support and timber lagging method, exist in Japan and they need risk mitigation measures against earthquakes as per our empirical knowledge. Many reinforcing measures for deformed tunnels that may be effective against earthquakes are developed; however, behaviors during earthquakes are not fully understood.In this study, static loading tests and numerical analysis, which simulate a loading condition during earthquakes, were carried out to clarify the effect of the countermeasures. The Load-bearing capacity is estimated for the tunnel structures facilitated by the installment of an inverted arch; however, a joint between inverted arch and sidewall become structural weakness. Rock bolts and carbon fiber sheets have a potential able to mitigate the risks of collapse of the lining by the forces from an earthquake.INTRODUCTIONA number of rock tunnels with no apparent unfavorable ground conditions suffered severe damage, including the collapse of their permanent lining, in large seismic events such as the Chuetsu Earthquake in 2004 (e.g., Mashimo 2005). Since these tunnels were considered to exhibit the required structural strength to survive earthquakes, studies are being carried out to clarify the mechanical behavior of tunnels during earthquakes and their damage mechanism (e.g., Kusaka et al. 2009); however, the aseismic design methodology for mountain tunnels has not yet been established.In many cases of earthquake-damaged tunnels, some defects already existed, such as improper construction and deterioration of lining concrete. Although countermeasures are usually implemented against such problems, their earthquake-resistant effect was not fully understood.In this study, static loading tests and numerical analyses to reproduce these tests were carried out assuming that a rock tunnel was affected by the earthquake to clarify the mechanism of the lining damage and the effect of the countermeasures."

Jan 1, 2016

By Gerald Pinter, David Nitsche, Márton Bredács, Markus Haager, Andreas Frank

"The reliable prediction of service lifetime of tunnel constructions is of essential technical and economic interest. Polymers used for tunnel liners have to fulfill the requirement of 100 years lifetime. However, today no reliably proven test method is available which confirms such long lifetimes. The current paper introduces a recently started research project which focuses on lifetime prediction of highly flexible, very low density polyethylene (VLDPE) for tunnel geomembranes. Different PE grades in combination with different antioxidant packages are conditioned at elevated temperatures and immersed in different media. Initial results confirmed significant material aging of unstabilized resins already after exposure of up to 34 weeks, at least at the highest exposure temperature of 80 °C. To consider application relevant material properties the material characterization was done by means of tensile tests and dynamic oxidation induction temperature tests. High pressure liquid chromatography was used for further investigation of antioxidant consumption kinetics. 1. INTRODUCTION For a reliable service of modern tunnel constructions a sustainable proofing against water infiltration is essential for the lifetime of the structure. Geomembranes made of polymeric materials have been used successfully for tunnel lining since several decades. Whereas previous geomembranes usually were made of plasticized polyvinylchloride (PVC-P), due to several technical advantages today very low density polyethylene (VLDPE) has become a more and more popular material for such applications. For modern geomembranes, current guidelines expect minimum lifetimes of at least 100 years (ÖBV-Richtlinie 2012). In contrast to this requirement it must be considered that today no test methodology is available which reliably confirms such long lifetimes of polymeric materials."

Jan 1, 2016

By A. G. Royle

Although these exhibit similar structures overall, there are more acute valuation problems in alluvials. Most of this description will therefore be about alluvials with comments on bedded vis-a- vis alluvial deposits where necessary. Although geological comments refer mainly to lateritic deposits the method of valuation described applies to all bedded deposits, e. g. coal, limestone, phosphate. In general, the more a deposit suffers alteration during or after its formation and the more the sampling process disturbs its material, the greater the difficulties of valuation. Emphasis is laid on structure, as in any kind of deposit valuation cannot proceed until its structures are understood. Not all the structures found in alluvials will occur in bedded deposits, of course.

Jan 1, 1982

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By A. T. Yu

The broken hill proprietary company Ltd., Australia's only steel producer, has come a long way. Since 1885 to reach today's. Capacity of 6.6 million long tons of ingot steel per year.* its Newcastle steel complex in New South Wales, located 100 miles north of Sydney and on-stream since 1915, has likewise shown continued impressive growth (fig. 1). The most recent expansion plans at Newcastle call for sub¬stantially increasing its production, with the help of some added facilities, but principally relying on the increase in efficiency of the furnace operation. Its modern raw materials blending system will playa major role in meeting Newcastle's new targets.

Jan 1, 1969

By C. E. Jordan

The Bureau of Mines has investigated the fundamentals of fatty acid/fuel oil conditioning for improved flotation selectivity. Both conditioning time and intensity can provide optimum flotation selectivity as well as good recovery. Traditional conditioning seeks to optimize conditioning parameters with subsequent recovery of the hydrophobic mineral. In the fatty acid/fuel oil system many silica gangue particles are also rendered hydrophobic by the flotation collector. Fundamental studies have shown that particle-particle collisions transfer the collector reagents selectively to the mineral surfaces with the highest affinity for the reagent. This mechanism deactivates the gangue particles while increasing the collector reagent loading on the selected mineral. The degree of this transformation is directly related to the number of particle-particle collisions which can be controlled through conditioning time or conditioning mixing intensity.

Jan 1, 1995

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By E. G. Noble

Microbial leaching is being investigated as a method for recovering the metal values from a domestic low-grade manganese wad ore. Early work showed that heterotrophic microorganisms present in the ore solubilized manganese when cultured in a glucose-mineral salts medium. More recent shake-flask tests using molasses as the sole nutrient source extracted 97 pct of the manganese from minus 300- µm ore in 4 weeks. Column bioleaching with the molasses medium solubilized 99 pct of the manganese from minus 6.3-mm ore in 50 weeks. The results of flask, column, and lab-scale heap bioleaching studies are presented.

Jan 1, 1991

By Gennaro Gerald Marino

In this paper the main subsidence- ground-structure interactions and an overview of the response of surface structures to subsidence ground movements are presented. The purpose of the paper is to augment our understanding for more effective application of available data as well as to highlight the essential site conditions in building response. The data presented general1 y applies to houses to structures up to 2-3 stories high and no more than several hundred feet in length. Superstructures of these buildings are supported by exterior (wood-frame or masonry) bearing walls with the interior floor loads carried by essentially one row of interior columns. This paper is not directed towards the response of tall buildings, steel-framed structures, or building types commonly associated with schools, churches, libraries, etc.

Jan 1, 1986

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By V. Adamek

The specific lithological conditions over the Pittsburgh coalbed, highly resistive limestone and sandstone units with relatively shallow overburden, prevent the use of any predictive method as developed for European conditions. This paper describes the development of a subsidence precalculation methodology suitable to the mining-geological conditions in the Northern Appalachian Coal Field. It has been found that due to lithological conditions over the Pittsburgh coalbed the subsidence coefficient varies within the area of the subsidence trough. This is different from the European conditions where the subsidence coefficient is considered to be a constant. The effects of lithology, in-the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hypothetically homogeneous overburden and existing lithological conditions, while providing for different mining conditions. Field data from eleven Bureau longwall panel studies were used in the regression analysis. For each panel the characteristics of the variability of the subsidence coefficient along individual profile lines were defined. Regression analysis of the subsidence coefficients from all test sites on the location relative to the edge of the panel has yielded a third degree polynomial equation with a coefficient of correlation of 0.9999. All sensitivity tests have shown good results.

Jan 1, 1985

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents.

Jan 1, 1981

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004