Search Documents

By M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is underway at the Twin Cities Metallurgy Research Center, Bureau of Mines. The new route from concentrate to metal includes 2-stage fluid-bed treatment; pelletized concentrate (33 percent Cu, 7 percent S) is first desulfurized (to about 0.5 percent S) in an oxidizing atmosphere, and in the second stage the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10 percent CaO is routed to a smelting furnace to separate metallic copper from the gangue. Recovery and the Cu content of the product at this point are in the 97-98 percent range. The metal must be refined to remove sulfur and iron to make wirebar copper. An important feature of the process is the pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment, which has permitted shorter reaction time, decreased dusting, and facilitated subsequent processing.

Jan 1, 1970

By A. K. Sinha

A great potential market for the high BTU midwestern thermal coal exists if the coal is desulfurized and prepared to meet the environmental restrictions and the utility customer specifications. Because the midwestern coal is very high in pyritic sulfur, it can be adequately desulfurized by removing the pyrite with the help of such coal cleaning techniques as the froth flotation. Froth flotation cells are now commonly employed in modern coal preparation plants for recovering the fines but they are not utilized for desulfurizing the coal probably due to a lack of system operating data for such applications. A research project recently conducted at Southern Illinois University shows that the total sulfur in the midwestern coals can be successfully reduced from as high as 5.3 percent to less than 1.4 percent by single stage froth flotation. The results obtained on ten different samples of high sulfur coal obtained from different areas in the Illinois Basin are presented and discussed.

Jan 1, 1985

By K. F. Unrug

Extrapolation of the rock properties obtained from the cores exploration holes to the surrounding areas often causes problems because of frequent sudden changes in the geologic composition of strata. To address this problem, the author has been developing a method of rapid strength testing "in situ," with application of a borehole penetrometer. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. The results are generated by strength determination on the wall of a drill hole at a site. The newest development is a borehole penetrometer that requires only a 1.38.mm (1.5 in) diameter hole. The small diameter of the penetrometer body allows for drilling test holes with production mine equipment such as roof bolters. It opens the possibility of broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 1999

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By D. Y. Geng

Longwall mining is a relatively new mining method in the United States. Early trials in the eastern and central coal fields were not successful, mainly because, among others, the face supports did not have sufficient capacity. It was not until in the late 1960's, when the high- capacity self-advancing powered supports became available, that longwall mining was successfully reintroduced. Since then the number of mines employing the longwall method has been steadily increasing. It has reached approximately 7.5% in 1981. Currently longwall mining is used mainly in the Appalachian coal field. The seam depth ranges from 150 to 2500 ft. but mostly between 300 and 1400 ft. The seam thickness ranges from 32 to 144 inches with the majority between 40 and 100 inches. Nearly all longwall mining are in flat or nearly flat seams extracting in single slice, although one inclined and one thick seam longwall mining have been either operated or initiated in Colorado.

Jan 1, 1983

By R. L. Nielsen

The thematic mapper (TM) aboard Landsat II records image data at seven wavelength intervals or bands. Three record the visible region; three record reflected IR energy. A false color image combining bands 7, 4 and 2 rendered as red, green and blue respectively provides maximum discrimination of rock types in arid regions. Structural analyses and interpretation defines regional structures, large volcano-tectonic features intrusive complexes, all which localize mineralization. Special digital processing using the ratio: Band 3 / Band 1 can identify limonites and other iron minerals. The ratio: Band 5/ Band 7 identifies clays and alunite. These ratio images show features and patterns of hydrothermal mineral systems: ?patterns of sulfide and alteration zoning in large porphyry systems, and zones of strong silica, quartz-alunite-illite, and pyrite-sericite in epithermal centers. Thus, digitally processed Landsat TM images are a cost effective and rapid means to recognize altered areas and define targets for large mineralized systems.

Jan 1, 1995

By Marcel Michaud

Over the past five years, the two-fold growth in Canada's coal industry "Figure, 1" results primarily from the coking coal market to Japan and, to a lesser degree, by the increasing use of sub-bituminous and lignite coal for power generation in the Prairie Provinces. This expansion will continue, but production of coal for domestic thermal generation of electricity will grow at a faster rate than coking coal exports "Figure, 2". Half of the 20 million tons of thermal coal used for electrical power generation in Canada during 1974 were imported by Ontario Hydro from U.S. coal companies in West Virginia and Pennsylvania. Ontario Hydro's Nanticoke station on Lake Erie which will consume 7.5 million tons of coal in 1977 when fully operative, as well as other future planned projects, could cause Ontario Hydro's coal consumption to rise from 10 million tons today to 20 to 25 million tons by 1985

Jan 1, 1975

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By William Hodder, Lisa Smiley, Ehsan Alav

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km and be lined using a precast concrete segmental tunnel liner with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT liner was grouted through ports drilled in the segments. The Westerly Storage Tunnel (WST) in Cleveland will extend approximately 2.93 km long and will be lined by using a similar precast concrete segmental tunnel liner with an internal diameter of 7,620 mm and external diameter of 8,230 mm. The WST liner was grouted using both grout ports built into the tail can of the TBM and through segments. Each tunnel was mined primarily in shale with varying levels of weathering and both tunnels had dry and wet sections. This paper will document the means and methods for grouting in each tunnel as well as the methods utilized to proof grout and the results found.

Jun 13, 2021

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By Douglas Ball

An underground storage field is a gas field where man, not nature, has put all or most of the gas. All but one of those in use today are in the pore spaces or "porosity" of sedimentary rocks, the most common being sandstone. The one exception, near Newcastle, England, is a gas storage in a cavern dissolved from rock salt. The tens of millions of barrels of LPG (liguified petroleum gas) now stored in salt caverns mined in shale is liquid storage, not gas storage, and in this paper I recognize the presence of these installations but do not include them in the gas storage category, Since, with the English exception, gas storages are gas fields, they can all be sorted into the categories used to describe gas fields, 95% of them once gas fields anyway, but some of the remaining 5% are the ones having the greatest effects on underground waters.

Jan 1, 1960

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By L. A. Clark

Although vein-, syenite-, and pegmatite-type deposits are known in Saskatchewan, recent intense exploration stems from discovery of several exceptionally high grade uranium and uranium-nickel deposits locallized near the basal unconformity of the 1.3-1.4 b.y. Athabasca Sandstone Formation. Graphitic basement rocks and post-Athabasca faulting or brecciation coincident with the unconformity are important in locallizing uranium deposits which form as tabular, shoe lace-like bodies with grades averaging over two percent and containing up to 50,000 tonnes U308. Some deposits have similar nickel contents. A few published sandstone analyses average 0.8 ppm uranium while basement granitoid and meta-sedimentary rocks vary from 0.5 to 20 ppm. In the proposed genetic model, traces of uranium are leached from these rocks by oxidized formation waters sweeping through the sandstone and along faults. Solutions are reduced and uranium is precipitated as basement graphitic meta-pelites are encountered along brecciated fault zones.

Jan 1, 1979

Information Technology has addressed those problems unique to senior management in the mineral industry. In general, these problems are those concerned with decision-making. Peter Drucker in his discussion of making effective decisions identifies five phases: (1) define the problem, (2) analyze the problem, (3) develop alternate solutions, (4) decide the best solution, and (5) convert the decision into effective action. The scope of the chapter by Guernsey addresses the first three phases which provide input to the decision-maker. The decisions to be made relate, in most instances, to the economics related to a mineral property or process. Computer models have been designed to generate these economic and financial evaluations. No one model is appropriate to the solution of all management's problems. In this chapter several applications are identified and summarized; a model for the economic evaluation of a mineral property is described in greater detail. The implementation of such models is dependent on the unique needs of management.

Jan 1, 1979

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By Thomas A. Wheeler, Robert O. Keys

The choice of the flotation reagent that suits a particular coal has become more complicated with the development of new, more efficient reagents. Frothers and conditioning reagents, in particular, have experienced a dramatic reevaluation of their role in floating various types of coals. This paper offers a better understanding of how each of the following factors contributes to the reagent selection: 1. Natural Flotability 2. Degree of Oxidation 3. Size Distribution 4. Percent Solids in Feed Slurry 5. Fluctuations in Plant Feed 6. Limitations on Froth Handling 7. Clean Coal Specifications 8. Ash Content in Feed a) discrete ashable minerals b) inherent ashable minerals 9. Water Chemistry 10. Petrographic Composition of Coal 11. Free-Swelling Index 12. Convictions of Customer The application of conditioning reagents - both promoters and emulsifiers can substantially improve the coal recovery. Some low-rank, hydrophylic coal, previously considered unfloatable can be economically recovered with the use of the proper reagent.

Jan 1, 1986

By Kenneth E. Merklin

The heavy media process is now being used extensively throughout the world for the gravity concentration of a great number of different minerals. The process is a commercial adaptation of the heavy liquid procedure which has been used in laboratories for many years to separate mineral of different specific gravities. In the heavy media process, a suspension of finely divided particles in water is used to increase the apparent specific weight of the fluid to the desired separating point. The original heavy media process used sand, galena, pyrite and occasionally other materials as the solid constituent of the separating suspensions. As the process developed, the need for a more universal media meeting the following requirements was recognized: 1. High specific gravity. 2. Resistance to abrasion. 3. Resistance to corrosion, 4. Readily reduced to a suitable size consist for suspension in water. 5. Available in quantity at economical price levels. 6. Easy to recover by a simple method.

Jan 1, 1958