Search Documents

By Wolfram Schnabel

Recently Lurgi has succesfully commissioned Peru's first direct reduction rotary kiln at SIDERPERU?s Chimbote works. The order included comprehensive engineering services and supply of special equipment to modify three existing cement kilns according to the SL/RN process. The kilns were cut to 62m length and installed with a slope of 2.5%. A new heating system, including shell burners, was supplied and inlet and outlet ends of the kilns completely renewed. Figure 1 shows the kilns after modification.

Jan 1, 1981

By Thomas S. Kovach

In today's competitive energy market, every effort must be made to assure the lowest possible production cost. 'rhi s. paper describes the cooperative effort between the coal producer and the utility customer to develop and install a fully integrated mine information management system at a 2.5 million tpy lignite mine in east Texas. A description of each item of the modules is included along with the problems encountered during development and how they were corrected. The system configuration is also described.

Jan 1, 1989

By Joseph Rosta

The gold and silver review did not arrive in time for publication in the May issue. Gold The gold market generally was listless in 1992, although investors returned to the metal in the fourth quarter. The gold price declined for the second year in a row, averaging $11.05/g ($343.76/ oz), 5.2% lower than the $11.65/g ($362.44/oz) seen in 1991. The average price has declined more than 23% since 1987, when gold averaged $14.36/g

Jan 1, 1993

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By C. C. Graham

In this paper, the problems which occurred on introduction of dense medium cyclone coal washing in Australia are reviewed together with the subsequent measures taken to obtain a satisfactory magnetite. Specification and testing of magnetite for exploration, quality control and in-plant check purposes is discussed. The disposition of Australian magnetite deposits in relation to the main coal producing areas is examined, and comments are made on the economics of mining, milling and beneficiating magnetite for coal preparation uses alone. Future trends in the Australian Coal Industry are predicted, and the need for a planned approach for the future is demons traced.

Jan 1, 1982

By John J. Dwyer

As one begins to contemplate the organization of a talk with the title "Iron Ore - The Permanent State of Evolution," the main divisions appear to be the past, the present, and the future. But distaste for repetition of the present production achievements, which scarcely need additional description on this occasion, soon leads one to the conclusion that a more appropriate division of the subject is simply the past and the future . . . with emphasis on the future. We are working in the present, but it can only be understood by what has taken place in the years and decades gone by, and/or under what terms we will have to face the future. Evolution is more often thought of as a steady change - but steady change is really the product of revolutions, sometimes making headlines but often unnoticed at the time. With hindsight, we recognize the great importance of the emergence of the Bessemer converter and the open hearth and the vast influence that both have had on steel making and the changing ore demand. In this country we also see schooners opening the era for lake transportation of iron ore from Michigan to Take Erie. Later, steamships haul the ore from the Mesabi Range to the steel centers of the country. In order to take full advantage of the inland seaway, there had to be revolutions in ship design, loading and unloading facilities and channel and lock development. Full scale utilization of the resources of the Mesabi Range, itself, required parallel upheavals such as the development of new production equipment, and substitution of modern forms of energy for horsepower, and, yes, manpower, as well.

Jan 1, 1968

By Michael L. Clar

Reclamation of surface mined lands has two basic objectives: (1) the elimination or abatement of undesirable environmental conditions, and (2) the restoration of mined land to its former or more productive uses. This paper addresses some of the planning concepts and site factors that influence the selection of suitable land uses for surface mined lands. Three planning concepts included in the discussion are: (1) mine land planning, (2) comprehensive land use planning, and (3) environmental site planning. The site factors that will influence the selection of an appropriate land use have been grouped into three categories: (1) legal, (2) geographic, and (3) natural. The natural factors are further subdivided into three groupings: geomorphology, soils, and climate.

Jan 1, 1981

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By John K. (Original by) Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1981

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro NC treating crude Waelz Oxide (WOX) to produce Special High Grade Zinc by a hydrometallurgical process, comprising leaching, zinc solvent extraction/electrowinning (SX/EW), melting and casting and bleed treatment. Cadmium removal by zinc dust cementation plays an essential role in the bleed treatment circuit to prevent a build-up of cadmium in the circuit. Silica, although not present at significant levels in the WOX feed material (approximately 0.3%), had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also impacted. The silica levels were mapped throughout the circuit in an attempt to identify the source of the silica issues. Adjustments including using PLS as feed to cementation, pH control in WOX leaching and neutralization have been introduced to mitigate the issues created by silica gel in the circuit. INTRODUCTION Located in North Carolina, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz Oxide (WOX) to produce Special High Grade (SHG) zinc. The flowsheet, known as the Modified Zincex® process, consists of leaching, solvent extraction, electrowinning, melting and casting and bleed treatment as illustrated in Figure 1. Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The Cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press Silica can be found in several forms in acid leaching. The first form is fine silicate particles. The size of the particles can vary from one to twenty microns (1). Fine silicate particles can lead to the formation of crud in solvent extraction circuits (2, 3). At Mooresboro, crud has been observed in Depletion, which is part of the solvent extraction circuit. Silica content in the solution in this section is high. The second form of silica is monosilicic acid Si(OH)4, which begins to polymerize almost immediately upon being leached into solution. Monosilicic acid polymerizes to silica gel or a silica precipitate dependent primarily on supersaturation (5). Factors that influence the rate of polymerization include temperature, sulfuric acid concentration / pH, hydrofluoric acid concentration, seeding, and dissolved salts concentration such as zinc and aluminum in the solution (4, 5, 6). In sulfate systems, silica solubility is reported in the range of 150 to 450 ppm of SiO2 (3, 5, 7)."

Jan 1, 2016

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By Ralph J. Anctil, James E. Palmer

According to relatively recent estimates by the US Geological Survey and the US Bureau of Mines, there are more than 0.9 Tt (one trillion tons) of remaining identified coal resources in the seven major western US coal-producing states and about 200 Gt (220 billion tons) in the demonstrated reserve base. Considering coal's current national production level of 0.7 Gt/a (0.8 billion tpy), these US reserve and resource figures are reassuring. Given here is a preliminary analysis of geologic constraints and an estimate of their effects on mining and recoverability of western coal. Mining Constraints USGS and USBM coal figures incorporate only thickness and depth, and are "blind" to many other major geologic constraints on mining and recoverability. The most important of these geologic constraints include: • coal seams too thin or too thick for conventional mining methods; • coal seams that cannot be mined due to insufficient separation from underlying or overlying previously-mined beds; • unstable or otherwise unfavorable roof strata; • soft or heaving floor strata; • coal seams that are too lenticular or discontinuous for conventional mining methods; • coal seams in intensely faulted areas; • coal seams having high angles of dip precluding the use of conventional coal mining methods; • coal seams that cannot be mined due to proximity of water-bearing strata; and • coal quality problems such as excessive ash, sulfur, chlorine, or sodium. Coal Thickness Present USGS-USBM classification for reserve base includes bituminous coal beds more than 0.7 m (28 in.) thick and subbituminous beds more than 5 m (60 in.) thick to depths of 305 m (1,000 ft). Both of these thicknesses are less than the thicknesses now considered mineable in the western US. The lower limit for bituminous steam coal in deep mines is about 1.5 m (5 ft). For subbituminous coal, a thickness of at least 2.4 m (8 ft) is generally required. Accordingly, the Bureau of Mines reserve base includes many thinner coal seams that will not be mined in the foreseeable future. Within the Powder River Basin of Wyoming and Montana many seams-Wall, Upper Pawnee, Lower Pawnee, Cache, Manning-range in thickness from 7.6 m (25 ft) to more than 30 m (100 ft) and occur at depths to 305 m (1,000 ft). These have been included in the Bureau of Mines reserve base. However, the mining technology required to mine these thick seams does not now exist. It will require many years for development. The ultimate recoverability from these thick seams is unknown, but could be as low as 25%.

Jan 8, 1982

International Minerals & Chemical Corp.'s New Wales operation near Mulberry, FL, is reportedly the world's largest concentrated phosphate chemical fertilizer and phosphate-based animal feed ingredients complex. Its latest expansion represents a $191-million investment. Two Northwest draglines were put to work at the operation early last year and, according to a company spokesman, total production from the units have more than doubled that from older rigs. This article describes how the draglines are used and provides details on the New Wales operation. The principle product at New Wales is phosphoric acid, produced by reacting ground phosphate rock with sulfuric acid in large concrete attack tanks. For each ton of phosphoric acid produced, New Wales must dispose of about 4.5 t (5 st) of waste gypsum. New Wales stores the gypsum on-site, and uses durable Northwest draglines to help handle the material. Two Units Maintain the Gypsum Stack After the gypsum is separated from the phosphoric acid through 23-m-diam (75-ft-diam) vacuum filters, it is mixed with water from a 121-hm2 (300-acre) recirculating cooling pond and, in slurry form, is pumped to the top of a 121-hm2 (300-acre) gypsum stack located adjacent to the cooling pond. The slurry contains mostly gypsum (CaSO4), with small traces of silica and other elements. The water at this point is corrosive, containing from 1-2% phosphoric acid. Its pH usually ranges from 1.5-2.0. Water drains from the gypsum stack into the cooling pond. Only about 15% of the pond's water, however, comes from the gypsum stack; the balance is from various sources throughout the complex and is held in the pond to cool before being returned for reuse in the plant. About 97% of New Wales' water needs come from this recycling program. The gypsum remains on the stack, inert, ready for future processing if it becomes economically feasible. Throughout the handling process, Northwest draglines work around the stacks' rim, continually directing the waste flow and digging out dried solids to heighten the perimeter dike to provide more storage volume. When wet, gypsum is extremely soft. When dry, it compacts well and provides footing with enough bearing capacity to support the machines. Processing at New Wales started in 1975 and the gypsum storage area has already been built up 12 m (40 ft) above grade. A total of 14.8 km3 (12,000 acre-ft) of solids are now stored. The draglines dredge material from near the perimeter dikes and place it to build parallel berms. This

Jan 8, 1982

By Mritunjoy Sengupta

The Green River formations in the Western U.S.A. contains vast amounts of petroleum reserves in oil shale deposits. Exploitation of this petroleum reserve calls for large scale mining of the oil shale. Applicable mining methods include conventional underground mining using roan and pillar, sub-level caving and block caving; underground insitu retorting of oil shale and open pit mining. Roam and pillar mining offers one of the most economic methods of underground mining of oil shale. A 2.4 x l09 litre per year (50,000 barrels per day) of crude oil production would require a daily oil shale production of 100,000 tomes per day from underground operations. For this large production, a highly mechanized room and pillar mining muld utilize large capacity diesel equipment such as 85 tonne trucks and 8m front end loaders. The total air requirements of an oil shale mining operations can. be as high as 28443/s. Ventilation planning for such a large scale underground mining operation presents a formidable task. The major objectives of providing ventilation air to underground workings are to dilute airborne .dust and diesel fumes to harmless levels, and to insure that the mine environment is compatible with the health and safety of mine personnel. Regulation of air velocities and air temperatures is a major factor in mine environmental control. Colorado State law requires that a minimum of 0.047m3/s of fresh air be supplied for each kW of diesel power operating underground. Additionally, 0.047m3/s of fresh air must be supplied for each underground employee, and a minimum air velocity of 0.15m/s must be maintained in all working places. It is desirable to exceed this minimum velocity in order to prevent stratification of ventilation air. Moreover, Colorado law also stipulates the maximum allowable concentration of noxious gases mine air, below: ? C02 - 0.5% by volume, 5,000 ppm. ? CO - 0.005% by volume, 50 ppm. ? Oxides of Nitrogen - 0.0025% by volume, 25ppm. ? Nitrogen Dioxide 0.005% by volume, 5 ppm. This paper examines ventilation requirements for the underground mine, with respect to air quality requirements and distribution of air in mine workings in light of the above regulations. Analyses were made for sane typical mining plans to determine airflow resistance or pressure drops and fan horsepower requirements. In addition, the possible occurrence of high concentrations of toxic gases, was examined. Expected temperature levels in mine workings were approximated.

Jan 1, 1980

By Ottmar Burghardt

Sintering of iron ore has undergone a dramatic development world-wide. Today, the annual world production amounts to approximately 600 million tons. At present, the sintering process in competition with pelletizing, seems to offer certain advantages inasmuch as it allows the use of solid fuels. Also, its charging behaviour in the blast furnace is, in general, considered as being better than that of pellets. This is true, in particular, for the charging behaviour and the gas permeability in relation to the grain size. Moreover, instead of charging limestone into the blast furnace, for instance, the basic components which are necessary for the burden materials can generally be supplied in a simpler and more cost-effective way by using basic sinter instead of basic pellets. While in sintering, with basicity rising to the range of 1.6 to 1.8 CaO : SiO2, the capacity increases and the sinter quality shows improvements in most of its characteristics, the pro¬duction of basic pellets generally requires a higher fuel rate, when compared to acid pellets, while production capacity decreases and some of the quality characteristics deteriorate.

Jan 1, 1982

By Jack D. Melin

The commercial development of the Liwell Screen is a result of a thorough search for a non-blinding and highly efficient screening device capable of handling even the most difficult-to- screen feed materials. A proprietary development of Hein, Lehmann A.G. of Duesseldorf, West Germany, the Liwell Screen utilizes a unique flexible deck motion for sizing a variety of sticky, high surface moisture feed materials including raw coal and lignite at separations ranging from 3/4-inches (19mm) down to 10 mesh (1.5 mm).

Jan 1, 1983

By W. F. McDermott

The Iron Ore Industry has perhaps seen more varied and drastic changes in its approach to crushing and grinding in the last 5 years than any of the other mineral industries, Multimillion ton per year plants have become common place. Centralized control and computers have become an established benefit. Autogenous grinding along with a variety of rod and ball grinding flowsheets are in use. This morning I will discuss a few of the more important and new concepts in the control of these crushing and grinding circuits.

Jan 1, 1970

By A. E. Hall

The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 1, 1988

By Edita Vircíková, J. B. Hiskey, Ludovít Molnár, Peter Lech, B. J. Scheiner

This paper describes the results of a study of hydrometallurgical methods of producing sodium arsenate for the glass industry from arsenic oxide wastes occurring in carbon dioxide washing. This paper addresses the following aspects: theoretical assumptions for leaching arsenic and its oxides, experimental results of As(III) oxidation to As(V) in aqueous solutions, sodium arsenate crystallization (the system As2O5-Na2O-H2O), characteristics of the crystalline product, and pilot-plant tests using sodium arsenate in the glass industry.

Jan 1, 1993