Search Documents

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

By Harold Rees

[This report supplements and brings up to date a paper prepared earlier this year for presentation at the Eleventh Pan American Railway Congress to be held in Mexico City, October 18 to 31, 1963. In order to acquaint the reader with the background of this project practically all of the first paper is included in the report.]

Jan 1, 1963

By Kiseong Hyeong

Geochemical characteristics, shapes and surface textures of manganese nodules from two blocks located in the southern (9°N~11°N) (KR5) and northern parts (16°N~17°N) (KR2) of the Clarion-Clipperton fracture zone between 130°W and 133°W were investigated in terms of sediment distribution and metal contents for better understanding of controlling factors of seabed manganese nodule genesis. Two blocks, ~700 km away, are dominated by the nodules with different origins, each of which has distinctive chemical compositions and shapes. KR2 block is dominated by irregular and poly-type nodules of hydrogenetic origin with low Mn/Fe, Cu, and Ni contents and high Fe and Co contents, while KR5 block is dominated by discoidal and ellipsoidal nodules of diagenetic origin with high Mn/Fe, Cu, and Ni contents and low Fe and Co contents. In addition, nodules from two blocks show different surface textures: smooth and transitional in KR2 and dimorphic and rough in KR5. Sediment distribution is also distinctly different in two blocks. The study area consists of three sediment types: Unit 1 ? dark brown mud with an intermediate metal content, Unit 2 - yellowish brown mud with poor metal content, and Unit 3 ? black metalliferous mud. KR2 is characterized by the thick occurrences (<250 cm) of Unit 1 at the surface while Unit 1 distributes thin (<12 cm) in KR5. Higher primary production rate in the southern block proximal to equator and resulting high supply rate of metals to the sediment might be the cause for the dominance of diagenetic nodules in the southern block, but potential controls of different sediment distribution on the nodule genesis can not be excluded. If it is the case, Unit 1 with an intermediate metal content likely has been acting as a sink for metals by precipitating micro-nodules within the sediment column. Within the KR5, the hydrogenetic nodules occur preferentially on the seabed where Unit 3 distributes at shallower depth (<50 cm). Unit 3 has 2 or 3 times higher metal contents than other types of sediments. It might play the same role as Unit 1 in the northern block that prevents the supply of metals to the sediment surface. It also supports the potential effect of sediment distribution on nodule genesis. Keywords: Nodules genesis, Sediment distribution, Supply rate of metals

Jan 1, 2008

By Xingang Wang

Spontaneous combustion is one of the most important safety issues in the global coal industry. It is considered to be a trigger for explosions in underground mines, especially for gassy mines. This thermal event is not easily detectable in the gob and sealed area. It is also a tough job to find the most likely hot point accurately. Admittedly, determination of the propensity for spontaneous combustion before mining activity should be a necessary step in the design of a mine and ventilation plan. However, due to the complexity of the chemical and physical properties of coal, spontaneous combustion has not been fully understood. According to a proximate analysis of coal, it is believed that sulfur and volatile matter in coal are the main intrinsic factors that cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal?s self-heating should be quantified. This study aims to improve the previous mathematical model developed by the authors for studying a coal?s propensity for spontaneous combustion. It enhances the model?s ability to consider the effects of sulfur, volatile matter and moisture content in the coal ? three important factors affecting a coal?s self-heating process. Based on the law of energy conservation, heat release rates for pyrite oxidation and moisture condensation are built into the model. Finally, the simulation results in terms of time versus temperature are calibrated with adiabatic testing data extracted from the literature for pyrite oxidation and moisture condensation, respectively. From the modeling results, it is found that the higher the pyrite content the coal contains and the more moisture that condenses in an environment with high relative humidity and initial temperature, the higher the potential for spontaneous combustion.

Jan 1, 2014

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By B. A. Kuyper

The Cove gold-silver deposit is located 50 km southwest of Battle Mountain, Nevada and 1.5 km northeast of the McCoy Mine. Total proven and probable reserves are 48.7 Mt (53.7 Mst) with an average grade of 1.85 g/t (0.054 oz/st) Au and 87.1 g/t (2.54 oz/st) Ag. Mineralization is hosted by Triassic carbonate and siliciclastic rocks in two separate orebodies. Oxide ore consists of disseminated gold and silver in clay-altered, manganese-flooded limestone. Sulfide ore is dominated by pyrite-sphalerite-galena veins in siliciclastic rocks and sandy dolomite. Gold and silver occur in the native state, associated with the base metal sulfides. Mineralization is interpreted to be the distal expression of a porphyry system. The McCoy gold (copper) deposit is interpreted to be the proximal expression of the same system.

Jan 1, 1991

An incremental-analysis-based stope design and cutoff grade calculation method was developed for an underground metal mine project. Traditional stope design methods are typically very time consuming and lack consistency and accuracy by manually drawing stope shapes. For quick reserve calculation and economic analysis, a new method named "3D incremental analysis based stope design" was created for mine-wide stope designs. The key idea of this method is to replace engineers&apos; manual checking of each incremental ring with one calculation of all the rings, and to build the final stope shape with the maximum values. This process was realized through a 3D ring grid setup and proper naming conventions for rapid calculations. With this unique but practical method, multiple options for a mine design were completed within a short time before the final selection of optimal cutoff grade and best stope designs for the project.

Jan 1, 2012

By A. S. Azman

In collaboration with Kennametal Inc. and corry rubber corporation, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a drill bit isolator to address noise overexposures associated with roof bolting machines in underground coal mines. NIOSH laboratory studies confirmed that the drill bit isolator reduces noise during drilling. Field studies were needed to confirm that a noise reduction could be obtained under working conditions and that the device was sufficiently durable. This paper reports results of field tests of the device conducted at five underground coal mines. Noise reduction was assessed by comparing the operator?s noise exposure during drilling with and without the drill bit isolator. Durability was assessed by recording the number of holes and total feet drilled with each bit isolator until either the test period ended or the device failed. The results from these tests showed that the device is an effective noise control in a mine environment. The field-tested drill bit isolators provided a noise reduction of 3-5 db(A). Of nine devices tested for durability, five exceeded 610 m (2,000 ft) drilled and two exceeded 762 m (2,500 ft) drilled before failure. Durability issues found in the field tests led to final production optimizations that have resulted in a commercially available product for drilling with 35-mm- (1.3-in.-) diameter roof bits and hexagonal drill steels.

Jan 1, 2012

By Lawrence Lien

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Universities and other training institutions are meeting the traditional skill needs required by the industry, but are the skill needs going to be the same in the near future? The answer may be no. Mining is changing because of increased liabilities and costs of environmental and safety is-sues; lower grades of minerals in traditional mining activities and the advent of new bio-chemical processes and robotic equipment. More productive and economic alternatives, and larger, more sophisticated and automatic equipment, are also changing the industry. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs and productivity. And, the industry will likely be engaging in more undersea mining, possibly space-based processing, less human interaction and more remote control of events than was previously thought possible.

Jan 1, 2011

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

By J. Noll

There is a need for direct tailpipe sampling of diesel vehicles in mines in order to determine the effects of an emissions-based maintenance program, evaluate control technologies such as diesel particulate filters and identify the worst diesel particulate matter (DPM) emitters in a fleet of vehicles. therefore, this study examined the performance of three portable instruments: a personal dust monitor (PDM) manufactured by thermo Scientific, a prototype elemental carbon monitor (Airtec) manufactured by FLIr and a prototype Ae91 instrument from Magee Scientific. These instruments were evaluated on the basis of their ability to provide direct reading tailpipe analysis for DPM. It was determined that the average bias of the tailpipe results from the PDM and the Airtec were 3±12% and 4±20%, respectively, when compared to the standard method of determining tailpipe particulate concentrations from a diluted exhaust. It was also determined that the Ae91 instrument correlated with the standard method.

Oct 1, 2013

By J. L. Huiatt, D. G. Foot, J. D. McKay

The US Bureau of Mines compared column flotation using either fine or coarse bubbles with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a &.7% Cr2O3-grade rougher concentrate with 87% recovery, compared with 43.8% and 43.5% Cr2O3-grade rougher concentrates with 85% and 77% recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse- and fine-bubble column flotation produced rougher concentrates containing approximately 41.5% Cr2O3 with 95% recovery, exceeding conventional flotation, which produced 35.6% Cr2O3 -grade concentrates with 87% recovery.

Jan 1, 1987

By Eric Ohl

Due to the world&apos;s ever increasing minerals and energy demands, process plants have to cope economically with ever growing throughput rates. This trend has accelerated the development of high capacity vibrating screens. Screens with screening areas of 30 to 50 square meter (322 to 540 square feet) and width of 5.5 meter (18&apos;) are technically possible and are being used presently with great success. This paper will concern itself with the general aspects of large screen design, by using modern technology and the latest findings with regards to fatigue strengths relative to the laws of vibration. It also will investigate the technical and economical limits of such designs.

Jan 1, 1983

By Paul Gribbon, Greg Colzani, Jim McDonald

The $300 million West Side Combined Sewer Over?ow Project consists of over5.5 kilometers of soft ground tunnel, an 833-million liter per day (220-MGD) deep shaft pump station, 3 kilometers of micro tunneling, and other miscellaneous shafts and pipelines. The construction contract, underway since September 2002, is a reimbursable cost plus fixed fee contract that included a quali?cations-based contractor procurement process and has undergone some modi?cation since execution. This paper will describe the contractual issues addressed to date, dispute resolution, where improvements can be made, and how an Owner can evaluate whether this type of contract is the best approach for an underground project.

Jan 1, 2005

By Robert J. Guardia, James Rustvold, Robert A. Robinson, Christopher A. Robertson

In 1999, the Bonneville Power Administration (BPA) replaced approximately 730 m(2,400 ft) of damaged 42- and 36-inch concrete pipe by microtunneling Permalock pipe through sand and partly below groundwater. Microtunneling saved $3.5 to $5 million from the estimated cost of a shored excavation and avoided a railroad and contaminated valley fill. A slurry microtunnel boring machine (MTBM) was used for two segments where groundwater was present and a wheel excavator MTBM was used for one segment where groundwater was not present. This paper describes design and construction of this project that was completed within 2% of the bid and engineer’s estimate.

Jan 1, 2001

By Marian W. Otrebski, Julian A. Korneck

Long distance, overland conveyors require significant capital outlay of which up to 70% may be contributed to the cost of belting. Significant savings may be achieved by identifying possible risk areas and applying modern technology methods to reduce or eliminate risk. Recently, Sasol Coal commissioned an overland belt conveyor system comprising three belt conveyors of 7 km, 5 km and 4.5 km in length. These were designed and constructed taking the above into consideration. Contained in the paper are the belt conveyor system requirements, designing assumptions and methods applied in the designing process as well as ways and means to eliminate or at least reduce risks.

Jan 1, 1998

By T. Gouri Charan, G. V. Rao

A spherical agglomeration process for the separation of scheelite fines of less than 30 µm in very low concentration of 0.04% WO3 in a binary mixture with quartz fines of less than 30 pm has been described. A concentrate containing 14% WO, with more than 90% recoveries could be achieved by means of anionic sodium sulfo succinate collector at pH 3.5 and also with commonly used anionic sodium oleate at pH 10.5 as per the conceptual flowsheet suggested. Such a process is envisaged as commercial potential for the recovery of fine-grained scheelite present in the tailings of gold plants as found in India.

Jan 1, 1991

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry&apos;s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Francis B. Gularte, James E. Monsees, John-Paul Whyte, Gary E. Taylor

In a short section of the Los Angeles Metro Rail system approximately 222.5 m (730 ft) of 6.4 m (21 ft) diameter twin-tube tunnels separated by a 1.8 m (6 ft) narrow pillar were designed to pass under a major eight lane freeway and a metropolitan intersection with only 3.7 m (12 ft) to 5.8 m (19 ft) of loose fill and alluvium cover. The design considerations and the chemical grouting program used to stabilize the alluvial materials is discussed. Also included is a discussion of the novel shield used for tunnel excavation and the effects of the subsequent fire.

Jan 1, 1991