Search Documents

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By M. M. Carpenter

Specialty chemicals are widely used in the industrial minerals process industry for many different purposes including beneficiation, filtration, flocculation, dispersion and biological control. Optimal use of such chemicals can confer benefits both in terms of cost efficiency and end product attributes. In this paper we will review recent progress in the fundamental understanding of mineral additive interactions and present data which show how optimization can lead to improved products.

Jan 1, 1999

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

Flotation of dolomite from apatite was investigated, using dodecylamine hydrochloride or sodium oleate as the collector, in the absence and presence of inorganic modifiers such as sodium chloride. Separation of dolomite from apatite was anticipated from the single mineral experiments under various pH and collector concentration conditions. Flotation selectivity in the mixtures, however, was found to be limited. Attempts to control the flotation response of these minerals by addition of salts such as NaCI and KCI indicated that selectivity is possible. The presence of sodium chloride was determined to depress apatite flotation using sodium oleate leaving dolomite flotation unaffected (Moudgil and Ince, 1989). In this paper, conditions for optimum separation and the effect of major parameters on the desired selectivity are discussed.

Jan 1, 1990

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By Q. Dai

In order to float coarse sylvite particles, Potash Corporation of Saskatchewan Inc. (PCS) uses amines and extender oil (Esso 904 oil). Since the content of polycyclic aromatic (PCA) compounds in Esso 904 oil is high, PCS has sought a suitable replacement. Various types of physicochemical tests, including measurements of the electrokinetic potential of emulsified oil droplets, oil/water interfacial tension and wetting of KCl plates by oil, did not provide conclusive results. However, captive bubble contact angle measurements on KCl plates in brine in the presence of flotation agents correlated reasonably with the flotation response. A few non-toxic oils were found to provide good results in the flotation experiments and are now tested under industrial conditions.

Jan 1, 1992

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

This paper addresses the valuation and development timing of an undeveloped mineral project. Traditional analysis has us developing the project immediately if its net present value (NPV) is positive. Option pricing theory finds that it is better to wait until the NPV of the property is significantly greater than zero before developing. Alternatively, when evaluating the development timing decision, we must calculate NPV using a higher "timing-adjusted" discount rate, and develop the property only if its NPV using this timing-adjusted discount rate is greater than zero. This paper uses option pricing ideas to convert this development timing advice into a more concrete and user-friendly decision rule: develop the project when its "development-timing NPV" is positive, this development-timing NPV being calculated using the normal discount rate.

Jan 1, 1997

By D. J. Torpy

With copper at its host depressed price in several years, producers are looking at every opportunity to cut costs in order to continue operating. Some of the measures that have been applied by different companies include reduction in manpower, high grading, and in some cases partial shutdowns. The most beneficial cost cutting measure implemented by Southern Peru Copper Corporation was to steepen the slope of the final pit limit from a conservative 37 degrees to an average of 48 degrees. By doing so, substantial cash outlays were saved. Southern Peru Copper Corporation (SPCC) operates two open pit copper mines and concentrators in the southern part of Peru, about 150 kilometers from the Chilean bordar. The Toquepala Mine went into production in 1960 and the Cuajone Mine in 1976. Both mines use shovel, truck and train operations. The trains, which haul ore to the crusher or waste to the dumps, are loaded either directly by shovels or by a transfer system. The Toquepala Concentrator treats an average of 43,000 tons per day and the Cuajone Concentrator an average of 55,000 tons per day. Concentrates are shipped via a 200 kilometer railroad to the port city of Ilo where the SPCC smelter is located. The annual production in the smelter from both mines is 290,000 tons of blister copper.

Jan 1, 1987

By M. R. Shahan, W. R. Reed

A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports, or shields. The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances. This paper will outline the design parameters for the development of the system, as well as describe baseline testing of coal and limestone dust. Results show the average instantaneous respirable dust concentrations that occurred during simulated shield advance. Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device. INTRODUCTION During longwall mining, miners can be exposed to respirable dust that is generated during the advance of hydraulic roof supports or shields. National Institute for Occupational Safety and Health (NIOSH) researchers have conducted numerous surveys of longwall mining operations, benchmarking the operating practices and dust control measures in use. It has been determined that the shields are responsible for 27% of the respirable dust that is generated on the longwall face [1]. The dust generated by the shield advances ranks second, next to the longwall shearer which is accountable for 43% of the respirable dust generated on the longwall face. The respirable dust generated during the advance of the shields can be a significant contributor to the respirable dust exposure of the mining personnel operating at the longwall face, especially since some of this dust is generated in the walkway. Control systems designed to reduce the dust levels generated during the shield advance have the potential to greatly reduce the respirable dust exposures of the personnel downwind of these activities. One control technology to decrease the dust generated by the shield advances would be to apply a layer of foam to the forward shield-roof interface prior to the shield advance [2]. The blanketed layer of foam would interact with the material located on the top of the shield during the advance, preventing a portion of that dust from becoming entrained in the mine air. This layer of foam would be applied using a foaming nozzle located on the longwall shearer body that would spray foam on the roof surface as the shearer passed. Substantial laboratory work has been completed to determine the feasibility of this type of foam application. NIOSH engineers have classified the various characteristics of foaming agents, using foam expansion ratio and drainage as important properties, as well as developed the mechanical systems required to apply the foam safely to the mine roof [2, 3]. The construction of an apparatus that could simulate the mechanical interaction between the dust-laden shield top and mine roof was necessary to adequately test the hypothesis that foam could be an appropriate control. A team of engineers designed and constructed a shield dust simulator system allowing for in-house testing prior to a full-scale field investigation.

Jan 1, 2019

By C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self-advancing hydraulic supports. U.S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology has greatly increased productivity. Past trends are used to predict future technological directions.

Jan 1, 1997

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By H. Sevim

Belt network simulators developed in the last two decades are reviewed. Critical parameters in belt network design are identified, and the capabilities of belt simulators in providing values of these parameters are investigated. An alternative design model that optimizes values of the critical parameters is introduced. To illustrate the capabilities of the alternative model, a real life case is treated and the outcomes are discussed.

Jan 1, 1990