Search Documents

By W. G. Fischer

Trona ore at the Westvaco mine of FMC Corporation has been obtained by room- and-pillar methods since the mine began operation. The flat-lying, 10-foot bed of trona, Na2CO3 NaHCO3 2H2O, is covered by 1500 feet of weak shale and sandstone. Extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early 60's forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans' were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. Roof cones troy in the longwall methods appeared to be more satisfactory than that found in room-and--pillar techniques. It was therefore felt that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 1, 1966

By M. Brändström, R. Dube, J. Moyo, T. Perkins, G. Bermudez, L. Bartsch, C. Smith, R. Sorensen

The Kennecott Copperton concentrator is currently the bottleneck for the Kennecott operation and several projects have been initiated to increase throughput. This increase in grinding circuit throughput has resulted in a coarser grind size which has impacted flotation circuit recovery. Metso Outotec 300m3 forced air tank flotation cells are currently utilized in the rougher flotation circuit at the Copperton concentrator. Higher overall recoveries have been observed on the newer Outotec tank cells compared to the original 85m3 self-aspirated flotation cells they replaced. However, coarse particle flotation response on these large, forced air cells did not show encouraging results when compared to smaller previously installed cells. This coarse recovery loss has been attributed to the longer froth transport duration and transport distance on large cells (100m3 and larger). Cell manufacturers addressed the risks of additional coarse particle losses in large cells by installing concentric circumferential launders and crowders (also called center launders). These are designed to reduce froth transport time and distance in the last cells in rougher stages where low residual floatable minerals causes a lack of froth mobility. The center launders also increase froth crowding, which also helps to increase froth transport velocity and increases copper and molybdenum recoveries. A trial set of the center launder retrofits were installed on the last three tank cells in one of the parallel rougher flotation rows at Copperton. The launder retrofits were installed at the end of October 2020 and monitored until March 2021. This six-month trial showed statistically significant improvements in copper and molybdenum flotation recoveries through the rougher circuit.

Mar 2, 2022

Unplanned ore dilution can have severe impact on the economics of a mining operation. The paper discusses and distinguishes between controllable and natural parameters influencing ore dilution, and how it can be minimized in longitudinal mining systems of narrow vein orebodies. It is shown through data of surveyed stope profiles and numerical modelling that unplanned ore dilution is a function of stope design and construction, orebody geometry, and rock mass characteristics.

Jan 1, 2010

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By J. Villeneuve

Steady-state simulation has proved to be a very useful aid in designing new plants and optimizing existing ones. The algorithms and data definitions of existing simulators often, however, require a great deal of expertise for implementing a simulation-based methodology. The constraints imposed by conventional simulators are explained and the advantages of a new algorithm, the Objective-Driven Simulation, are shown. These advantages are a) an improvement in the simulation results, which enables simplifications of the methodologies used, and b) the possibility of taking into account economic objectives for plant operation, thus extending the range of application of steady-state simulation.

Jan 1, 1992

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By W. J. Miles

Diatomaceous earth or diatomite is a sedimentary rock of organic origin that is composed principally of the silicious skeletal remains of diatoms. Diatoms are microscopic single cell acquatic plants that are related to algae. Diatoms first became abundant in the Cretaceous period from about 65 to 135 million years ago. Most of the commercial deposits are of Pliocene through recent age, and are younger than 35 million years. Diatoms are still abundant in present day lakes and seas. The living diatom is supported and protected by two half cell walls or valves united by a connecting band or girdle. These valves are composed of opaline silica extracted from the water in which the diatom lives. After death of the diatom, the silicious remains settle in the lake or sea and accumulate at variable rates approaching several millimeters per year for very active diatom colonies. This accumulation of silicious sediments, after decay of the organism, burial, and uplift, can result in the formation of diatomaceous earth deposits.

Jan 1, 1987

By G. F. Revey

Most commercial explosives contain 70 to 94% ammonium nitrate, by weight. When portions of these explosives end up in shot rock and ore, through spillage or incomplete detonation, ammonia and nitrates leach out of them and into ground water. In recent years, State and Federal regulators have been applying more stringent water quality standards, particularly at new mines and development projects. Bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice at most mines, when mining conditions allow it. ANFO use is desired because it less costly than other explosives, but when spilled it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. They either control explosive losses, or they treat mine effluents at the end-of-pipe. This paper addresses the former solution --controlling explosive losses. For both packaged and bulk explosives, guidelines designed to limit losses during storage, handling and use, are described in detail.

Jan 1, 1995

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By P. C. Miller

The paper reports laboratory results from the bioleaching of chalcopyrite ores and concentrates using a mixed moderate thermophile culture. Copper dissolution in excess of 95% was achieved in all cases with the majority of tests indicating copper dissolution in excess of 98%. Aspects of downstream processing are discussed in relation to iron rejection by precipitation. The laboratory results indicate the need for careful control of the pH value to prevent co-precipitation of the copper with iron. A comparison of capital and operating costs is given indicating potential differences between the use of toll smelting and bacterial leaching on site. A discussion is given highlighting the sensitive cost areas of these two process routes.

Jan 1, 1997

By M. J. Richards

Spontaneous combustion caused by the movement of air through the waste is a major problem. Combat methods attempt to exclude oxygen rich air, but little is known about airflow through the waste. The use of a tracer gas technique to monitor the flow of nitrogen from an injection hole during inertisation is described. Correlations are drawn between barometric pressure changes and the nitrogen entering the waste. As no information was obtained about airflow and oxidation zones, a second experiment was conducted to sample from the waste, but the results were inconclusive. A finite element method developed to model the pressure and airflow distribution, under steady state and nitrogen injection conditions is outlined

Jan 1, 1987

By James H. Barks

Commercial development of the mineral resources of southwestern Missouri began about 1850 and spread into southeastern Kansas and northeastern Oklahoma, forming the Tri-State Mining District with Joplin as the urban center (fig. 1). The value of the Tri-State mineral production from 1850 to 1950 exceeded one billion dollars, and until 1945 the region was the world's leading producer of lead and zinc concentrates, accounting for one-half of the zinc and one-tenth of the lead produced in the United States (Gibson, 1972 1). By 1950 most of the rich ores had been extracted, and mining and milling operations declined during the 1950's and ceased in the 1960's. The sulfide minerals, mainly galena and sphalorite, were mined from cherty limestones at depths of 25 to 75 m (meters). Crude ores were brought from the mines to the surface where they were milled into lead and zinc concentrates. , Barren rock was discarded in piles while the ore-bearing rock was crushed and ground into fine gravel. The minerals were separated from the rock by a jigging process and the tailings were skimmed off and discarded in large piles. Ground-water flooding of the mines was controlled by constant pumping. When pumpage declined in the 1950's and 1960's tile abandoned mine drifts and shafts filled with water. At present (1977) numerous tailings piles and flooded mines remain as visible evidence of the mining era and as a threat to the quality of ground and surface waters of the area. In 1976 the U.S. Geological Survey in cooperation with the Ozark Gateway Council of Governments made a study of the effects of the mines and tailings piles on water quality in the Missouri part of the Tri-State District. The study area covers approximately the southwestern quarter of Jasper County, an area of about 725 km2 (square kilometers), and is bounded by long 94 o 15' w.' and the Missouri-Kansas state line, and lat 37 o 15 N., and the Jasper-Newton County line.

Jan 1, 1977

By Frank Cook

As in other areas of the country, surface coal mine productivity in the Central Coal Province--primarily Illinois, Indiana, and west Kentucky--has declined steadily since 1969 (figure 1). Productivity, as measured in tons of clean coal produced per man-shift, dropped 35 percent during the period 1969-1975. Unwelcome at any time, this phenomenon is particularly untimely now, when increased coal production is a national goal. The U.S. Bureau of Mines has been working with the coal industry to develop new operating methods and equipment to enable increased productivity and improved reclamation performance in surface coal mining. Several projects have involved identification and evaluation of existing overburden handling and reclamation practices, and development of means to improve operational procedures. Some results of one of those projects, as they apply to the Central Coal Province, are summarized in this paper.

Jan 1, 1977

By C. C. Harvey

As we move towards the 21st Century there are several factors that will influence the markets and processing requirements for industrial minerals. Traditional markets for many industrial minerals in the developed world are frequently stagnant or decreasing because of their maturity or due to environmental factors such as reclamation, recovery of byproducts, and recycling. Some industrial minerals are greatly affected by these factors, while others are either immune to or have adapted successfully to meet these challenges. In the developing countries of the world, there is rapid market growth and resource exploitation. The future of specific mineral commodities in several markets will be discussed.

Jan 1, 1997

By Harry Leslie Bullock

With silica making up more than 27% of the earth's crust, its oxides amounting to more than 59% of the igneous rocks and quartz the most prevalent of the main free oxides, it follows that the mining engineer' is in constant contact with quartz, mainly as a gangue material to be removed as completely and economically as possible and sometimes as a valuable mineral to be purified' for the chemical,, ceramic or glass industries. Water scarcity under desert or semi-arid conditions, dwindling water supplies and difficulties of wet waste disposal in many locations and trouble from freezing in arctic locations make dry benefication more and more desirable. Advances made during the last few years in apparatus and methods and a steadily increasing knowledge of solid state physics are widening the field open to the economical application of electrostatic separation.

Jan 1, 1967

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By Wieda Azani, Alexander Tarigan, Willem de Beer

In block caving, the rates and sequencing of undercut production blasting, drawbell blasting, and mucking are the key levers for attempting to manage cave performance. Cave performance encompasses a range of factors, which include growth, shape and the effect of the cave on the abutments, excavations, geological structures and lithology. We compare production data in several panels in the Grasberg DMLZ and GBC block caves with the seismic response in work areas, around geological structures, and in geotechnical domains. These comparisons enable evidence-based conceptualising of the effect of production rates and mining layouts. By also considering the correlation of seismic release rates in different parts of the rock mass, the wider influence of a cave can be gauged through considering possible stress and / or deformation transfer. This concept is not novel, but it is rarely implemented in a routine fashion, principally because production data rarely are easily available. Previously, it has also been used to retrospectively compare seismic hazard between different mines. This paper discusses practical, day-to-day tools to manage seismic response to mining. Therefore, the paper presents a methodology for presenting seismic release and production rates on integrated plots at any time to facilitate quick identification of correlated spatial regions. This methodology explores the production data collection and geolocation at Grasberg, which will be described in some detail.

Apr 26, 2022