Search Documents

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By P. W. King

The performance of the versatile McNally Wedag horizontal vibratory centrifuge for dewatering ultra fine 0.5 x 0.15 mm (28 x 100 mesh) material has proven to be success¬ful and the results presented herein will examine its capabilities in terms of capacity, solids capture, product moisture, effluent solids, and size analysis. Centrifugal dewatering of fine refuse has proven t to be another application for which this unit has performed exceptionally well.

Jan 1, 1985

By B. S. Hulvey

Thin support liners are becoming more accepted and being developed with improved properties because the mining industry as a whole has been offering underground safe test trial sites. This is because of the huge potential for such products. Recent developments tend to indicate that the technology is “coming of age” and these are discussed in this paper.

Jan 1, 2003

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Michael Li, Kathryn Rogers, Arie Moerman, Mike Cooper

The Brunswick Mine, a Division of Noranda Inc., produces zinc, lead, copper, and bulk lead-zinc concentrates through underground mining of a large massive sulphide deposit. The mining method employed is longhole open stoping with delayed backfilling. In 1996 Brunswick began a review of its mining methods and backfilling operations. In 1997 the decision was made to convert the backfill system from cemented and uncemented rockfill to paste backfill prepared from mill tailings. This paper will describe the features of the backfill preparation and distribution systems, review the handling of technical issues, and discuss experiences since plant commissioning.

Jan 1, 2001

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By Charles F. Herbert

It is difficult to decide who most deserves credit for discovery of a mining district that has produced over 19.8 Mg (7,000,000 fine oz) of gold and still contains a large reserve of low grade ore. Fred Culver may have made the first discovery. In the summer of 1867, the ship's log of the Hudson's Bay Co.'s steamer Otter stated that Fred Culver had been found nearly lifeless from wounds, without provisions, but with some 2.3 kg (80 oz) of rough, placer gold in the bottom of his canoe; he told of finding a rich creek and an attack by Indians that caused the death of his two companions. The place of rescue was about 24 km (15 miles) southeast from the present site of Juneau. Possibly John Muir, the hero of modem environmentalists, should be given important credit. In 1879 he reported finding mineralization along what later became to be known as the Juneau Gold Belt, and it was his report that induced the cantankerous German mining engineer, George Pilz, to grub- stake some of the prospectors who had drifted into Sitka from the declining gold placers of Cassiar, British Columbia. Pilz also offered rewards to Indians who might report gold discoveries.

Jan 1, 1990

By W. M. Lewis

Product losses to tailings ponds have long been a source of frustration for the mining and utilities industries. The utilization -of the Lewis Econosizer to recover lost products has proven to be very cost effective through reduced acreage requirements, cleaning costs and increased production. The unit is successfully operating in coal, aggregates, industrial minerals, clay, fly ash, heavy minerals and many other ores. Utilizing an upward flow of slurry in a free settling environment, particles stratify within the unit according to settling velocities and are removed as sized products. Ultra fines or clarified water is removed off the top of the unit. The Econosizer requires no power and only minimal maintenance.

Jan 1, 1998

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By C. H. Sheerin

Remotely located in the jungle near mount Puncak Jaya [16,500 ft (5,030 my), Irian Jaya, Indonesia rests Freeport's Indonesian copper mining operation. Shortly after start up of Freeport's copper concentrator in 1972, lower than estimated throughput was experienced within the crushing circuit. Within one year, Freeport had successfully engineered a solution, and was operating a 5,500 dmtpd wet screening circuit. Today, after 19 years of successful wet screening expansion and operation, the concentrator processes 57,000 dmtpd.

Jan 1, 1993

By William F. Riggs

Inspiration Consolidated Copper Company, located in a semi-arid climate in Arizona, continually struggles with a water problem. This applies to quality as well as quantity. When the EPA considered installing a new centralized sewage plant to handle the combined waste from the municipalities of Globe and Miami, Arizona, they automatically assumed that He could use the sewage effluent for process water in flotation. The treatment plant was to be a tertiary system producing 1600 gpm of sewage effluent. Inspiration decided that this could possibly be a source of additional process water. It was decided to test sewage effluent from Miami Treatment Plant at the rate of 400 gpm since it was only a primary treatment plant. The 400 gpm was combined with the 5000 gpm of process water going to the Concentrator. After one week the results were disastrous. The recovery and final grade had each dropped approximately 5%. With the results from this brief run, it was concluded that sewage effluent from a primary treatment plant could not be used. Research was then brought into the problem to begin an evaluation of sewage effluent in flotation.

Jan 1, 1977

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By Ali Yalçin

The study area is located in the NW of Uluborlu (Isparta). Massive limestones and alluvial deposits form the lithological units of the study area. The average thickness of the alluvium deposit consisting mainly of light brown - red colored and fine grained clastic sediments which derived from the limestone is about 10 meters. The aim of this study to investigate the uses of this alluvial sediments as tile - brick material. For this aim, disturbed and undisturbed samples have been taken from different depths in the alluvial deposits. Mineralogical compositions have been determined by XRD and major oxide contents by XRF. Laboratory experiments have been carried out to determine the technological properties of the samples. The selected major oxide contents of samples vary between A12O3 (24.6 - 24.12 wt %), CaO (0.76 - 4.27 wt %), Fe2O3 (10.21 - 10.29 wt %), MgO2 (1.25 - 1.51 wt %). CaCO3 and MgCO3 values calculated from the geochemical analyses, are between 1.55 - 1.62 and 2.62 - 3.17 respectively. The ratios of grain size of the samples are 82 % for < 0.2 mm and 5 % for > 3 mm. Geochemical analyses and technological features of the samples indicate that these fine grained sediments of alluvial deposit are suitable in terms of uses as tile - brick material. The potential reserve of this tile - brick material has been determined as 40 million tones.

Jan 1, 2005

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder&apos;s Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By S. J. Root

The mineral processing industry supplies raw materials to a wide variety of manufacturing sectors. Large companies such as Ford, Microsoft, and Johnson&Johnson have pledged carbon neutral supply chains in the coming decades, leaving suppliers to reevaluate their energy sources [1–3]. National Renewable Energy Lab [4] has partnered with over 700 organizations with similar goals in mind. The energy needs are broad in scope in the mineral processing industry. Generation IV of nuclear reactors, which is currently under development in both the private and public sector includes a class called microreactors like the small modular reactor XEnergy plans to install at Dow Chemical’s Gulf Coast facility by 2023 [5]. As the name implies, these are smaller than the utility scale nuclear power plants in operation today, and are intended to be more versatile. A specific reactor core design, along with modules could be selected to fit a certain application without needing to design a greenfield power plant. Basic water cooled designs could easily supply shaft work, electricity, and low grade process heat to a facility. More advanced designs, such as molten-salt-reactors and high-temperaturegas-reactors can achieve higher temperatures needed for ore roasting. Similarly, these reactors could produce hydrogen by high temperature electrolysis to use as combustion fuel and reducing atmosphere in blast furnaces.

Feb 1, 2023