Search Documents

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

By William A. Riggs

Salt, a non-metallic mineral whose use dates back to earliest history of mankind, and whose uses cover the widest range for any mineral raw material, is generally of widespread occurrence in commercially recoverable quantities in the oceans, in certain sedimentary rocks, in certain lakes, and in certain underground waters. Passing over geological detail, it may be said that, generally, all of the salt in the world has, at least once in geological history, been in solution in the oceans. The total salt content of today's oceans, said to equal 4.5 million cubic miles of rock salt, dwarfs the tremendous volume of salt in the sedimentary rocks. In 1958, United States production of salt was about 22 million net tons and world production about 82 million. About 3 percent of United States production is table salt, with chemical, municipal, industrial and agricultural uses taking the remainder. Mississippi River. Figure 1 has been expanded sufficiently to show also those salt occurrences and producing points which might economically ship salt into these states. Although widespread in occurrence, salt deposits and possible production areas generally show very sharp local boundaries. Salt-for non-table use is susceptible to ?place value?, a common problem in low valued raw materials, where transportation costs often exceed the value of the material f.o.b. the production point. Generally only large capacity mechanized salt producing operations can compete in United States markets, as contrasted to the many small local salt evaporators in less industrialized Mexico.

Jan 1, 1962

Fossil resin types occurring in the Hiawatha seam of the Wasatch Plateau coal field, Utah, have been separated according to color and their physical and chemical properties evaluated. These resin types were separated into four color fractions, yellow, amber, light brown, and dark brown. Each resin type has then been subjected to comprehensive spectroscopic examination and other physical methods of characterization. Included among the spectroscopic methods of characterization are FTIR and 13C NMR spectroscopy. Physical properties that have been measured include density, optical, and magnetic properties. These analyses reveal that the resins are distinct from other macerals, predominantly nonaromatic in nature with small amounts of oxygen functionalities and a low degree of unsaturation. The four resin types show distinct differences in certain physical and chemical properties such as density, hexane solubility, magnetic susceptibility, and aromaticity.

Jan 1, 1990

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

New Mexico?s active coal mines have reclamation challenges that are being successfully resolved through the application of geomorphic grading methods. Soils and overburden material are often of poor quality, and annual precipitation is low. Revegetation on south and west aspect slopes often failed to persist. The New Mexico Mining and Minerals Division had therefore been encouraging topographic diversity on reclamation to improve water harvesting and reduce the percentage of south aspect slopes. Steeply dipping, multiple coal seams may be mined by open pit methods. Structurally-controlled trellis drainage patterns that exist premine have to be replaced with dendritic drainage patterns on reclamation where the overburden had been pulverized. Sodic spoil material is prone to differential settling and the creation of piping features in areas where runoff ponds, which may lead to downslope instability. In each of these scenarios, the approximation of natural drainage patterns on the reclamation has reduced erosion and sedimentation by creating shorter slopes with correct profiles, and by improving conditions for revegetation establishment.

Jan 1, 2010

By David Oliveira

"INTRODUCTIONOne of the key drivers for the selection of a mechanized tunneling method in good quality rock masses is a good excavation advance rate. In order to achieve satisfactory advance rates, a good geotechnical performance of the rock grippers in main beam open tunnel boring machines (TBM) is required, besides other factors related to ground support and the performance of the cutter head.One well known potential issue of main beam gripper TBM is associated with the bearing capacity of the tunnel side walls while crossing fault zones or poor rock masses in general. Such a mechanism is similar to that of footings on rock and perhaps the most common problem associated with gripper performance. Depending on the quality of the rock, the rock under the gripper contact may experience significant damage and crushing (Figure 1), eventually affecting the TBM advance rate due to a lack of tunnel wall reaction/support. Such a mechanism is primarily dependent on rock quality, applied loads and gripper size.In the case of large diameter TBMs (e.g., D > 12 m), a second potential failure mechanism may arise associated with the loss of confinement within a rock pillar between twin tunnels, even in good quality rock but particularly in bedded sedimentary strata. Punching of the rock pillar may develop due to excessive shear along bedding partings and sub-vertical joints (Figure 2), particularly under a low stress environment. As a result, this mechanism is dependent on both the rock pillar width between twin tunnels and stress conditions around the tunnels, in addition to the previous factors described for the first failure mechanism."

Jan 1, 2016

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come, but they are just around the corner. This paper presents a vision of this up-coming revolution in our industry. This vision is comprehensive. It includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For our industry to realize maximum benefits from the information age, we must have a vision of the future that is shared by technologists, machinery producers, and miners.

Jan 1, 1994

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By K. N. Han, H. C. Cho, R. Kim

"As an extension of the work on the effect of OH- on various cations in hydrometallurgical systems, the effect of Cl-, Br-, I- and CN- on cations such as Ag+, Cd2+, Hg2+, Cu+, Cu2+, Co2+, Zn2+, Pb2+ and Sn2+ has been examined in detail. The Newton-Raphson technique has been used to determine the amounts of various metal species as a function of the concentration of anions. Some practical implications of various metal complexes in metal separation and removal from solutions have been examined and discussed.IntroductionUnderstanding the role of anions in hydrometallurgical processes often determines the success of an operation. The successful choice of concentration and type of anions not only leads to an effective extraction and removal of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2009; Al-Tarazi et al., 2004), but also to assisting effective separation of various metals, whether it is a solvent extraction, ion exchange operation or even a simple precipitation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974).This paper continues the discussion of the role of anions in hydrometallurgical systems beyond the role of OH-, which was the topic of a previous paper (Kim et al., 2014). Table 1 lists various anions that are frequently used in conjunction with metal ions to be selectively separated or precipitated. As seen in the table, many anions are used frequently in hydrometallurgical practices. Some of the more frequently used anions include OH-, SO4 2- and CO3 2-. The halogen elements, Cl-, Br- and I- , as well as CN-, are also used in hydrometallurgical applications, especially in relation to noble metal recoveries (Meng and Han, 1994; Zhang et al., 1996; Sun et al., 1996; Starovoytov et al., 2007)."

Jan 1, 2015

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company's successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By S. Cotten

The concept for a Mine Escape Vehicle (MEV) is motivated by the desire to enable personnel to evacuate a mine rapidly as the first and most desirable response to any underground emergency. Under a NIOSH contract, Raytheon UTD developed a conceptual design for a vehicle that coal miners could use to facilitate their rapid exit from an underground coal mine in the case of emergency, including fire or explosion. The vehicle requirements include the capacity to provide life support functions for a number of miners, operate in an oxygen deficient, low or no visibility atmosphere, and travel at speeds faster than miners can walk out of the mine. To develop the MEV concept, three primary tasks were identified and executed. The first task focused on developing a realistic concept of operations (CONOPS) and associated high level vehicle requirements. The second task identified and evaluated currently available equipment and technologies that could be applied to address the CONOPS. The final task developed a design concept that integrated the identified components for the five (5) MEV sub-systems to provide the foundation for future detailed engineering design and prototype construction. The resulting MEV design concept is centered upon retrofitting existing mine personnel carrier chasses with available, mine-worthy equipment capable of addressing the MEV requirements. This approach offers a practical and economic avenue to prototype development and delivery with minimum lead-time and risk. Furthermore, by integrating familiar and available equipment into the design and CONOPS, the resulting Mine Escape Vehicles should also be more readily accepted by the mining industry.

Jan 1, 2010

By Donald E. Scheck

Blasting practices based on sound engineering principles are well established but the successful application of these practices requires accurate information about the overburden geology and close supervision of the drilling and blasting operations. Good design alone is not sufficient to insure good results, but the process may be difficult to control unless steps are taken to measure the variables and to provide management and the operators with the information they need to establish and maintain control. Satisfactory blasting can be defined as loosening and fragmenting the rock so that it can be handled by the excavating equipment, while at the same time, governmental regulations on air blast and ground vibrations are not violated. Optimum practices achieve these objectives at the lowest combined cost of the drilling and loading operations and the blasting materials. Total system optimization, that is, taking into consideration the effect of fragmentation on the cost of operating and maintaining excavating equipment as well as drilling and blasting costs, probably is not a reasonable goal at the present time.

Jan 1, 1984

By Thomas P. Meloy

Theoretical development of comminution models has come about in the last 10 years. These models assume that the material being broken is homogeneous and that the compression or energy wave is uniform throughout the specimen. Obviously, this is not the case because most comminuted materials are rocks with either many phases and/or definite grain size. The mathematical models deriving the size distribution of daughter fragments resulting from the comminution of brittle, single particles are of two schools. The first model, proposed by Gilvarry in 1961, was based on the concept of volume, surface, and edge flaw activation. The second, proposed by Meloy in 1960, was based on the concept that the crack density is a function of the energy in the comminution wave. The flaw theory has run into increasing theoretical problems and is now being abandoned. On the other hand, the crack density theory has been expanded and has successfully considered the case where there are inhomogeneities in the comminutive wave. However, the main constraint of a homogeneity in the solid being comminuted has hitherto never been overcome. In this paper, a very general derivation of the crack density model is made for inhomogeneous solids by replacing the assumption of homogeneity with an arbitrary function, P(y), which describes the susceptibility of the material to comminution as a function of position. The restraints on this function, P(y), are very broad and, hence, the derivation is extremely general. General use of the equation derived necessitates a detailed a priori knowledge of both the fracture process and of the physical properties of the material being fractured; this knowledge is expressed in open form as, P(y), the linear probability density that a plane of fracture intersects at point y on an arbitrarily oriented line segment of total length xo through the original particle. From these assumptions, a general expression for the cumulative mass distribution of particles resulting from fracture is then postulated. It is: [ ] where, B(x), is a cumulative mass of material finer than size x, r is the average number of crack,, (y), is defined above and xo is the initial particle size. It is shown that suitable assumptions reduce the expression to the theoretical results of Gaudin and Meloy and to special forms of the empirical equations of Rosin-Rammler, Gaudin and Schuhmann. Semi quantitative agreement is demonstrated by Grimshaw with experimental results of a very complex fracture of heterogeneous sandstone blocks. A need is expressed for more theoretical development of P(y), and a more extensive experimental study of both homogeneous and heterogeneous fracture. The full mathematical derivation is presented for the first time in this paper. The general implications of the equation and its application are also discussed.

Jan 1, 1968

By P. G. Semple

For the last four years, the Kilborn Group of Companies (Kilborn) has been involved in several major projects in the CIS. These projects include the Kumtor Project, the Kubaka Gold Project, the Kazgold Project, the Aginskoe Project and the Jerooy Project. These projects are all in various stages of detailed engineering and construction. In this paper, Kilborn will discuss our experience in the CIS and share some insight into project development in this geographic region.

Jan 1, 1996

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013