Search Documents

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

Provide an economic alternative to drill-blast excavation with the same ability to excavate openings of varied orientation, shape, and size. Approach Develop an efficient, adaptable, mechanical excavation machine that produces unconfined tensile failure in rock. How It Works A drill-split fragmentation machine that combines a drill and a unique splitter has been developed. The drill and splitter are mounted on a carriage that positions the splitter in a hole immediately after it is made by the drill. The splitter creates force loads that cause the rock to fragment, and the process is repeated for excavation. The unique splitter applies both radial and axial loads to the rock mass, which produces an excavation action comparable to pulling a plug. This excavation action distinguishes the radial-axial splitter from typical demolition splitters, which require a free surface parallel to the axis of the splitter toward which to break rock.

Jan 1, 1989

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By Ronald S. Conti

This paper describes technology and training that has been identified for underground emergency responders. Historically, underground mine rescue teams have only received training in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fie drills every 90 days in a smoke-free environment, this does not fully prepare them for the conditions that will be encountered in real escape situations. Therefore, it is extremely important that miners are provided with adequate technology and that training simulations are conducted in a realistic manner. A series of mine rescue training and mine emergency response development (MERD) exercises, and in-mine smoke training was developed, conducted, and evaluated by state and company teams, and by National Institute For Occupational Safety and Health (NIOSH) personnel. The training exercises were held at NIOSH's Lake Lynn Laboratory (LLL) and operating mines during the past several years. This training resulted in improved technology and training for mine rescue teams, fire brigades, first responders, and miners in general. For example, existing technologies were identified to help responders during exploration and recovery operations. These included various chemical light shapes, strobe lights, light vests, and laser pointers to identify team members. Most of these devices may be used to mark underground areas and certain mine materials. Strobe lights were used for mapping out escapeways and lasers were used to negotiate travel through smoke. Thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, and allows the user to easily locate missing or trapped personnel and heated areas. A hands-free communication system showed potential for enhanced communications between team members, the fresh air base, and command center. A new team lighted-lifeline allows for flexibility in movements of team members during routine tasks and allows them to easily find their fixed position on the lifeline. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. A positive-pressure inflatable escape device (IED)/airlock, was used to isolate the "hazardous" environment from fresh air and allow rescue team members to traverse through. An inflatable feed- tube partition that can rapidly block large openings such as underground passageways or tunnels and simultaneously provide a feed-tube for high-expansion foam generators was also deployed during the simulations. These technological advancements have improved the state of readiness for rescue personnel and have increased the chances of survival for all personnel escaping from underground emergencies.

By L. E. Jackson, E. W. Dean

One of the refining processes to which lubricating oils are frequently subjected effects a reduction in content of paraffin wax. The actual treatment usually involves chilling and filter pressing; the most important result accomplished from a commercial point of view is lowering of the ""cold test"" of the oil. The Bureau of Mines has recently had occasion to ascertain the effect of changes in paraffin wax content upon the viscosity of oil and has conducted a series of experiments described in the present report.Object of the present investigation:The Bureau of Mines has devised and is using a method for the analysis of crude petroleum* which includes determination of the viscosities of lubricating oil distillates. The Bureau method does not provide for preliminary removal of paraffin wax, and it has seemed advisable to determine whether this omission causes any important variation from the results that would be obtained through commercial refinery processing. It was also thought that the present tests, though limited in scope, might be of some practical value in indicating the general effect of paraffin content upon one of the most important properties of lubricating oil.Experimental procedureA five-gallon sample of Pennsylvania crude petroleum was distilled at atmospheric pressure until 50 per cent of the charge had been vaporized. Two liters of the residuum was distilled at a reduced pressure of 40 mm. (absolute) and cuts were separated that came over between the temperature limits of 250° to 275° C. (462° to 527° F.) and 275° to 300° C. (527° to 572° F.). The viscosities of these fractions were determined and they were subsequently subjected to treatment that removed successive percentages of paraffin wax. Viscosity temperature curves were determined for the oil obtained after each removal of wax.

May 1, 1921

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site's restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model's data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

By R. D. Leitch

From time to time the Bureau of Mines has received requests from persons who wish to destroy unwanted explosives, and although the information that follows has been accumulated from sources considered reliable,4/ the. Bureau of Mines assumes no responsibility for accidents that may result from following the suggestions offered. Explosives to be destroyed may be fresh material from damaged packages, usable material for which there is no further need, or material that has deteriorated either from natural aging or from improper storage to the point where it is unfit for use.

Jan 1, 1945

Provide d comprehensive source of up-to-date information about technology for revegetating coal mined lands. Approach A great deal of activity and research in the field of coal mine revegetation has been reported in technical literature, both before and after the passage of Public Law 95-87, the Surface Mining Control and Ruclamation Act of 1977 (SMCRA). This information is widely scattered throughout books, scientific journals, periodicals, Government reports, and other sources, and there has been a need to develop a method of accessing it quickly and efficiently. At the request of the Office of Surface Mining Reclamation and Enforcement which promulgates and enforces regulations implementing the act, the Bureau of Mines has prepared a document that identifies literature relevant to coal mine revegetation. Most of the literature available on this subject has been published during the past 15 years. To tap this reservoir of information, 14 data bases were accessed from DIALOG SDI (Selective Dissemination of Information) Service using three keyword combinations (surface mining and reclamation, strip mining and reclamation, and revegetation). This procedure generated over 7,000 listings. The U.S. Department of Energy's ENERGY data base was selected from the 14 DIALOG bases, both for its large number of listings and for its broad coverage of literature. This data base contains all the unclassified information that passes through the Technical Information Center of the Department of Energy, including reports, journal articles, conferences, patents, books, monographs, theses, and engineering materials relating to energy development.

Jan 1, 1986

Analyze variably saturated flow in mining and other environmentally sensitive settings through the use of personal computer (PC) based software. The Problem There is an increasing need for mining companies to quantify water contaminants and their migration in the unsaturated zone. New and innovative computer models are therefore necessary to more accurately assess the potential impact of mining activities on groundwater resources and the environment. Applications for unsaturated flow modeling include (1) assessment of the impact of surface or underground extraction mining on flow conditions; (2) assessment of various hydrologic designs for resource recovery, such as in heap leaching or in situ leach mining; (3) assessment of the transport of conservative nonrcactive constituents in response to migration from spoil piles, or acid mine drainage; and (4) assessment of any combination of the above to facilitate expeditious permitting for mining operations. Since the mid 1970's there has been a proliferation of mathematical models and procedures for solving unsaturated now problems; however, few of these approaches have been integrated into software for public use. Commercially available unsaturated flow software models typically are limited to a single application and have restricted approaches. For example, computer codes that solve the unsaturated flow problem based on an analytic expression arc restricted to a simple geometric shape, homogeneous and isotropic materials, and provide only information regarding pressure and flow conditions in specified wells. The variably saturated computer codes that take advantage of the finite difference or finite element approach arc often restricted to either steady state or transient solutions; utilize one specific moisture-retention relationship and moisture-dependent permeability function; do not account for hysteresis; and are used with specific hardware such as a mainframe or work station. This restricts their use because they arc hard to interface, and arc often poorly documented, support dependent, and expensive. The mining community needs a flexible, more broadly based, variably saturated fluid flow simulator for the PC-platform to more accurately predict fluid movement in the mining environment.

Jan 1, 1991

By C. A. Herbert

"Haulage accidents usually are responsible for about 17 or 18 percent of all coal-mine fatalities and about 21 percent of all non-fatal coal-mine accidents. When the relatively small number of employees continuously exposed to haulage hazards is considered, it would appear that haulage is more hazardous than any other phase of coal-mine operation.Haulage accidents have increased from year to year, doubtless due to the increase in electrical haulage, and particularly to the use of larger cars, heavier locomotives, longer hauls, and greater speed. Unless very definite steps are taken to eliminate the causes of these accidents, they will continue to increase rather than be reduced, as they can and should be.Underground haulage in many of the large modern mines of today is similar in many respects to railroad practice. In recent years the railroads have made wonderful strides in reducing accidents, and instead. of being one of the most hazardous occupations, as it once was, railroading is now one of the safest. Doubtless, if thought and action, similar to that given to reducing accidents among railroad passengers and employees, were given to safety in mine haulage, under¬ground haulage accidents could be reduced in about the same ratio.Haulage accidents may be classified, according to responsibility, into two groups - those for which management is largely responsible and those for which the employee is largely to blame; there is, however, an overlapping of responsibility from one group to the other. If, therefore, haulage accidents are to be reduced, it is absolutely essential that both management and employees cooperate to this end.In the first group, for which management is largely responsible, may be included accidents due to faulty equipment, moor track, a poorly arranged system of haulage, lack of clearance or of overhead protection, and dirty roadways; even in these features, however, the employee is not without a measure of responsibility, as failure of haulage equipment possibly may be due to lack of care on his part, failure to report when equipment is out of order, or failure to do a good workmanlike job of installing or repairing or operating.To the second group of accidents for which the employee may be largely responsible, belong those caused by such careless practices as jumping on and off fast-moving trips, coupling on the ""fly"", running at excessive speeds, failure to properly block cars, and similar hazardous and unnecessary acts of omission or commission. If, however, management condones such practices, or, as in some instances, insists upon them, it must accept its share of responsibility for the accidents that inevitably result.Some of the most prolific sources of haulage accidents will be discussed briefly, together with the steps that may be taken to minimize their occurrence."

Oct 1, 1939

Now you know why there is concern about mine illumination. You have some idea about how the human eye works and about the problems of glare, peripheral vision, and accommodation. And you know that lighting in a mine presents special problems because of the dark surroundings and low reflectance. This chapter describes what can be done to improve conditions. This chapter begins with a short discussion about Federal Standards on mine lighting -- what they are and what is being done to carry them out. The chapter then describes different types of lamps that can be used for mine lighting, and discusses their advantages and disadvantages. Finally, the chapter lists some things that you can do personally to improve lighting, or can point out to others so that improvements can be made. The Federal Government is doing its part to improve mine lighting by establishing regulations. Lamp manufacturers are constantly studying new lamps to provide better equipment. And your company will do its part to comply with regulations. Better lights may not be here yet, but they will be soon. But in the end, you are the one who will be using the lights, and you are in the best position to see the improvements. You are also in the best position to see and tell others where further improve¬ments can be made.

Jan 1, 1976

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

SUMMARY AND CONCLUSIONS This report describes a study to develop a detailed set of guide¬lines and equipment recommendations to be used as a guide for mine operators, mine inspectors, and equipment manufacturers in implementing the emergency escapeway standards for metal and nonmetal underground mines. It was sponsored by the United States Bureau of Mines. The first part of this report reviews the historical background of metal and nonmetal mine fires and the development of present and proposed mandatory standards. This is followed by a discussion of the survey of representative mines and how the proposed standard effects these mines. The remainder of the report covers technical discussions of each escapeway component including a comprehensive computer sim¬ulation of mine evacuation. Following the technical discussion of each group of escapeway components is a list of the pertinent guidelines. A study of past mine fires indicates that a serious commitment by operators to the proposed escape standards would be instrumental in saving lives in the future. The most significant event in a recent mine fire, in which no deaths resulted, was the very early discovery of the fire. The evacuation was orderly thanks to careful preparation by the mine personnel. However, the mine was possibly only spared a real disaster because of the discovery of the fire almost at its inception. Installation of automatic fire and smoke warning devices may be the single most important step in preventing future disasters. The self-rescuer has saved many lives in mine fires. Men have also died while attempting to use them. The reason men died was either because the unit was not working or the miner did not understand how or when to use it. There is no good excuse for either of these conditions occurring. Regular maintenance and inspection should prevent unit failures. Frequent instruction on when and how to use the self¬rescuer would prevent confusion and potential fatalities. A means of

Jan 1, 1976

This chapter details the perspective from which collected data have been examined. The first part, intended primarily for lay readers, discusses several topics related to mining as an enterprise. Initially, the organizational functioning of atypical large mine will be described. It is the formal structure above a miner that decides the conditions of his or her work. A second point of concern is the technology itself An underground coal mine is a sociotechnical system, with workers and machines organized in particular ways during production. Third, general conditions and dangers underground will be described in detail. The physical environment of an operation is a powerful factor in the work life of miners. Fourth, a discussion of the process of formal training is given. During this training, a new worker is taught what the organization expects of him or her in the role of safe, productive, coal miner. Next, there are outside organizations that act as significant forces in the workplace. Examples include the Mine Safety and Health Administration (MSHA), State agencies, and the United Mine Workers of America (UMWA). The roles of these entities will also be examined. The second part of this chapter will depict each study site as a concrete setting, so that findings can be interpreted in their proper context. The Organizational and Technical Nature of Mining A coal mine is a complex system. It is defined as all parts of a mining plant's property (both underground and surface) that contribute, under one management, to the extraction or handling of coal [American Geological Institute 1997]. As suggested, many functions that must be carried out at an operation are only indirectly related to coal mining and processing. Even the jobs that are di¬rectly related tend to be numerous and varied [Wallwork 1981]. According to Palowitch [1982], the chief reason for this sophistication is that "after more than two centuries of exploiting our coal resources, today's coal industry finds itself saddled with a horrendous legacy of human impairments and environmental damages which society demands be corrected." Now, the effects of government regulation are evident in every aspect of the mining industry. Any operation, if it is to survive, must be administered with an eye for social efficiency and accountability. Long-range planning is needed to ensure that the mine produces coal in a cost-effective manner. One of the first things that must be considered is location and method of access. To extract coal from an underground mine, a coalbed (or "seam") must be reached from the surface. The term "portal" is generally given to any entrance that provides access to a coal mine. In hilly terrain, such as is found in Appalachia, the coal may "outcrop" on a hillside. This allows direct

Jan 1, 2000

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008