Search Documents

By E. J. Gleim

Contact with trolley wire in the mines of the United States has taken a considerable toll of life throughout the years that trolley locomotives have been employed as a means of' transportation. A study3/ of the records over a 15-year period for one State alone showed that, of 98 fatalities resulting from contacts with electrical circuits and equipment, 75 were caused by direct or indirect contact with unguarded trolley wire in coal mines. The law relating to guarding trolley wires in the mines of this particular State, as amended in 1935, reads in part as follows: "All trolley wires carrying 220 volts or more, and less than six feet six inches above top of rail, must be guarded at all points under which men and animals are required to pass***,'" The natural conclusion to be drawn from such records is that lack' of guards or shields must be held responsible for these fatalities. As a preventive measure, it has been advocated that every foot of trolley wire in mines should be guarded. Although some such drastic steps may appear to be amply justified, closer examination of the records nor this and other coal-mining States shows that absence of guards is not entirely responsible; but rather that other factors, such as carelessness and neglect it the observance of certain well-established simple rules concerning installation and location of trolley wires, also are responsible. In other words, if trolley wire is installed carelessly and its maintenance is neglected, it should not be expected that the mere installation of guards will overcome such carelessness and neglect. This publication discusses Various types of guards that have been used in Coal and metal mines of this country, together with related steps bearing upon the problem of 'preventing shock and fatalities from contacts with trolley wire. The material herein contained is taken largely from Information Circular 6577,4/ now out of print, and has been revised to include some types of guards that have been used in metal mines, together with a discussion of guard materials not covered in that publication.

Jan 1, 1945

By Stephen D. Cramer

The Bureau of Mines conducted a series of in situ linear polarization measurements in high-temperature, high-pressure hypersaline geothermal brines at the Bureau of Mines Geothermal Test Facility in the Imperial Valley of California. The measurements represented an evaluation of the linear polarization technique for obtaining instantaneous corrosion rates of materials of construction in flowing hypersaline hydrothermal fluids that rapidly form scales on exposed surfaces. A special method was devised for use with the linear polarization technique that resulted in obtaining corrosion rates for 1020 carbon steel, 316 and 430 stainless steel, titanium, various nickel-based alloys, and aluminum 6061 under strong scale-forming conditions. The measurements also provided information on scale-deposition rates in various geothermal environments. Exploratory in situ potentiostatic polarization measurements were made in the flowing brines to qualitatively determine scale-deposition effects on the electrochemical measurements.

Jan 1, 1978

By Liming Yuan

Three-dimensional computational fluid dynamics (CFD) modeling is conducted to simulate spontaneous heating in a large-scale coal chamber with a forced ventilation system. Spontaneous heating is modeled as the low-temperature oxidation of coal using kinetic data obtained from previous laboratory-scale spontaneous heating studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. The water vapor transfer and the effect of heat of wetting are not modeled. The CFD model is validated by comparing simulation results with test results from U.S. Bureau of Mines experiments conducted in the coal chamber. The model predicts lower temperatures in the early stage but agrees well on the induction time for spontaneous heating. The effects of airflow rate and order of reaction on the spontaneous heating process are also examined. The calibrated CFD model is found to be useful for predicting the induction time for spontaneous heating in underground coal mines.

Jan 1, 2009

By Robert L. Thorne

Cassiterite deposits on Sullivan Creek in central Alaska were investigated by the Bureau of Mines in the spring of 1943. Gold miners in the area have been recovering cassitorite each season as a byproduct of gold placer operations. Approximately 300 tons of tin concentrates have been shipped from the district. The deposits were sampled though trenches and small shafts. An average tin content of 0.28 pound per cubic yard was indicated. A detailed description of sampling methods and sample analyses is presented in this report.

Jan 1, 1948

By D. G. RUNNER

Information Circular 6148R, " Selected Bibliography of Minerals and Their Identification ," was issued in June 1929 , revised in July 1937, and again in October 1938. The popularity of this circular , combined with the desire to make it more comprehensive , has occasioned the preparation of this compilation of references . Where possible , date of publication , publisher, current price , and number of pages are given, although prices are subject to change at intervals . The references are grouped under the following headings : minerals , gems , rocks , geology, geomorphology, engineering geology , prospecting, mining . engineering, microscopy, technical dictionaries , and miscellaneous . For ready reference, the authors ' names are arranged alphabetically under each grouping . This list is not comprehensive, but contains only those references in most common use and which are generally available in public college libraries .

Sep 1, 1949

By J. W. Montoya

The chemical, mineralogical, and physical properties of berylliferous tuff from Spor Mountain, Utah, were determined in laboratory research conducted by the Bureau of Mines. Two beryllium-bearing minerals--a hydrated form of bertrandite and a berylliferous saponite--were found to be present in the tuff. Each of the beryllium mineral forms predominated in samples from certain areas of the district. The possibility of practicably separating the beryllium minerals from the tuff by physical methods appears remote because of the complexity and nature of the mineral associations. Beryllium mineralization in the region occurs in a rhyolitic tuff usually overlaid by unaltered rhyolite. The beryllium is distributed erratically throughout the tuff in individual mineralized bodies. Many samples of mineralized tuff were examined and found to contain from 0.2 to 1.8 percent BeO. All samples contained a hydrated form of bertrandite that was nearly cryptocrystalline, whereas samples from one area also contained a berylliferous saponite of variable beryllium content. Neither mineral has been previously reported, although related bertrandite-like minerals have been found in the U.S.S.R. and berylliferous minerals of the montmorillonite group have been synthesized. Most of the minerals of the tuff are finely crystalline, intergrown, and have similar densities. The complexity and intimacy of the mineral associations, the difficulty of achieving effective mineral liberation, and the highly friable nature are characteristics that lead to the conviction that tuff of the type examined cannot be effectively concentrated by gravity, magnetic, electrostatic, attrition, washing, sizing, or flotation methods.

Jan 1, 1962

By Harry W. Campbell

During 1983, the U.S. Bureau of Mines conducted a mineral survey of 19,700 acres that included the Fish Creek Mountains WSA (Wilderness Study Area), 15 miles southwest of the Salton Sea. Two United States Gypsum Co. claim groups in the WSA have more than .20 million tons of inferred gypsum reserves. These high-grade, surface and near-surface gypsum deposits are an extension of a gypsum bed that has been mined continuously since 1922. The Waters prospect in the central part of the WSA has large quantities of limestone suitable for many commercial uses. Sand and gravel is plentiful in the WSA in alluvial fan and ancient shore-line deposits. Limestone and alluvial deposits are not economic because similar material is closer to potential markets. No evidence of energy minerals or geothermal resources was identified in the WSA. A portion of the eastern Fish Creek Mountains WSA is leased for oil and gas exploration. United States Gypsum Co. holds eighteen unpatented placer claims in the northwestern part of the WSA. No other mining claims or mineral leases were identified in the study area. No mineral production is known from within the WSA.

Jan 1, 1986

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By Joan T. May

Anhydrous methods were tested for the extraction of beryllium from low-grade source materials. The purpose of the investigations was to find new extraction processes that are applicable to domestic ores. Beryl, helvite, and phenacite materials containing from 0.1 to 2.8 percent BeO were used as starting materials for direct halogenation tests and pretreatment followed by halogenation. The results of the investigations showed that direct fluorination and carbide-chlorination are two practicable methods that can be applied to low-grade concentrates. Treatment of concentrate-carbon mixtures with anhydrous hydrogen fluoride extracted 99 percent of the beryllium in the concentrate; the soluble fluoride product, converted to an oxide, contained 70 percent BeO. Chlorination of beryllium-silicon carbide, prepared from low-grade concentrates, extracted beryllium into the volatile chloride product.

Jan 1, 1962

By W. W. Weller

Low-temperature heat capacity measurements were conducted, and entropies at 298.15° K were evaluated for sodium monomolybdate (Na2Mo04), magnesium monomolybdate (MgMo04), and calcium monomolybdate (CaMo04). The 298.15° K entropy values were sodium monomolybdate, 38.1±0.3 cal/deg mole, magnesium monomolybdate, 28.4±0.2 cal/deg mole, and calcium monomolybdate, 29.3±0.2 cal/deg mole.

Jan 1, 1963

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By A. C. Johnson

The Ellington manganese deposit in Reynolds County J Mo., had been known for some time; and limited exploration, consisting of test pitting and sinking a shaft 54 feet deep on the property, had been done by private interests. Late in 1941, the Bureau of Mines cleaned, deepened, and sampled many of the existing pits and dug and sampled 27 new ones. The shaft was unwatered and sampled, and several pockets of manganese ore were trenched to determine their extent. Samples were analyzed and beneficiation tests on 1 ton of the ore were made at the Rolla, Mo., station of the Bureau of 'Mines. Results of the investigation indicated that the deposit was small and low in manganese content.

Jan 1, 1948

By John Nagy

Data from experiments and literature on gas and dust explosions in closed vessels are presented to show the effects of the vessel size and shape; the initial pressure, temperature, and turbulence; and the fuel-air ratio and the strength of ignition source on pressure and rate of pressure rise. An attempt is made to correlate some of these parameters with an elementary mathematical model. Analyses of data on 17 vessels--spherical, cubical, cylindrical, and rectilinear in shape--ranging from 0,018 to 905 cubic feet in volume were made. Although the study was initiated to provide information primarily on dust-explosion phenomena, some data were obtained for gas explosions so that the factor of initial turbulence caused by the pneumatic blast used to disperse dust could be evaluated. The mathematical interpretation of the explosion phenomena was in general accord with the experimental data, and correlation was obtained for several factors affecting explosion development. Neither vessel size nor shape affected maximum pressure (when heat loss was neglected). The rate of pres-sure rise decreased as vessel size increased, and the rate was proportional to the ratio of the surface area of the vessel to its volume. Induced initial turbulence markedly increased the rate of pressure rise and slightly increased the maximum pressure. Changes in initial pressure produced proportional changes in maximum pressure and rate of pressure rise. Initial temperature and maximum pressure were inversely related, but initial temperature had little effect on the maximum rate of pressure rise. Comparative experiments showed no appreciable difference in explosion development of gas and dust fuels. The vessels and experimental work are described, and all data are given in tables. The mathematical model will facilitate extrapolation from laboratory to industrial conditions and will allow comparison of results obtained in different laboratories.

Jan 1, 1971

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By Frank J. Susko

The U.S. Bureau of Mines has developed a computer model to describe a flotation process. Coal data from conventional flotation has been converted to a simple, two-parameter kinetic model developed by Reuter and van Deventer (1,2)3. Each set of coal data was represented by two constants, a and ß, and an average flotation rate. The success of the model was demonstrated when the calculated and experimental recoveries showed good correlation. The two-parameter model allows complex data to be defined much more efficiently than traditional knowledge-based models.

Jan 1, 2010

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946