Search Documents

By R. W. Huber

While conducting an investigation on electrolytic reduction of magnesium oxide in 1943, it became necessary to obtain accurate data on the conductivity and density of various mixtures of fused chlorides. AZ the required information was not available in the technical literature, or there were inconsistencies in the data from several investigators, an independent study was made at the Bureau of. Mines laboratory at Salt Lake City on the conductivity and density of the molten chlorides MgCl2, CaCl2, BaCl2, KCl, and NaCl and the binary mixtures of MgCl2 with the other four chlorides. Studies were also made on the binary system KCl-CaCl2 and on certain portions of several ternary systems. Measurements covered a temperature range from the melting point to 1,000° C. The results of this study were reported in an intra-Bureau report prepared early in 1944. Since then the Bureau of Mines has received several requests for data on fused chlorides; the results of the previous study, therefore, are being published to make the data available.

Jan 1, 1952

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By Shirley F. Colby

A continued rise in construction activity in 1941 forecasts further increases in the demand for building materials of mineral origin, Recent studies by the Bureau of Mines, United States Department of the Interior, reveal that sales of mine and quarry products and their derivatives as a class have followed the long-term trend of construction activity in the past and are benefiting now by the upswing in all types of building. At present most building materials of mineral origin are holding their own in the competitive arena. A few are slipping behind, but others have forged fax ahead. Prominent among those that have surpassed general construction activity since 1925 are sand, gravel, and crushed stone (used in concrete and road metal and railroad ballast) and cement. Both building stone and roofing slate have followed the building curve closely, although in the last few years sales of roofing slate have risen above the curve and sales of building stone have dropped below it. Clay products and building lime, on the other hand, have lagged behind the general procession. Gypsum sales likewise dropped behind, but during the last few years, this industry, thanks to the wider acceptance of its newer products, has staged a marked recovery so that it now stands in about the same relation to total construction activity as it did is 1927-25.

Jan 1, 1941

By S. R. Borrowman

Mill tailings from conventional uranium extraction processes contain nearly all of the radium originally in the ore. Such tailings require controlled storage in perpetuity to safeguard the surrounding environment from radioactive contamination. Alternatives to controlled storage of the tailings are (1) removal of the radium from the tailings for separate storage or use or (2) removal of the radium when processing the uranium ore. In laboratory tests conducted by the Federal Bureau of Mines, radium was leached from tailings using either hydrochloric acid or ethylenediamine tetraacetic acid. A hydrochloric acid leaching method was used to extract both radium and uranium from the ore to yield tailings containing less radium than those produced by either conventional sulfuric acid or alkaline leaching processes. From 77 to 94 percent of the radium in mill tailings was concentrated by sedimentation in slime fractions representing nearly 25 weight-percent of the original sample.

Jan 1, 1975

By Sol Weller

The Fischer-Tropsch synthesis consists of the formation of long-chain hydrocarbons by passage of carbon monoxide-hydrogen mixtures over metal catalysts, usually based on iron, cobalt, nickel, or ruthenium, at temperatures in the range 180°-300° C., and at pressures of 1-15 atmospheres. Although the reaction has been known and studied for more than 20 years, the mechanism by which it occurs is still poorly understood. One approach to understanding is to consider the effect upon the course of the synthesis of variations in each of the important operating variables. Consideration of the experimental data pertaining to these variables may suggest an over-all picture describing the synthesis - a picture which, in turn, would have to be consistent with all the known facts. The first part of this paper will be concerned with such a consideration of operating variables; the second portion will discuss recent work pertaining to the role of metal carbides as intermediates in the synthesis.

Jan 1, 1949

By A. Wahib Khair

"This article first describes the impact of respirable dust on the health of miners in underground coal mines in the United States of America. Second, it identifies the major sources of dust generation, namely cutting tools in the road headings. Two surveys associated with cutting tools were made to determine the useful life of these cutting tools, and to determine the effect of cutting tool wear on productivity of the continuous miners. Third, this article presents the results of a series of experiments carried out in the Rock Mechanics Laboratories at West Virginia University in order to study: 3.1 the effect of cutting tool rate of wear on respirable dust generation, 3.1.1 the effects of rock materials on tool wear and respirable dust generation, 3.1.2 the effect of cutting tool geometric parameters on respirable dust generation, and 3.1.3 the effect of tip materials used in the cutting tool on respirable dust generation. Recommendations in regard to cutting tool design are also presented in this paper.Silica and coal dust are the two major elements affecting the health of underground miners. According to Lemen [1] approximately 1,500 men died due to breathing in silica dust in 1936 while tunneling through a mountain of mostly silica, near the town of Gauley Bridge, West Virginia. Coal dust resulting in lung diseases in one of the major health hazards in underground coal mines. The impact of black lung on miners, coal workers' pneumoconioisis (CWP), has ranged from 16,000 to 23,000 each year since 1982 [1].The trend for conventional mining to continuous machine cutting of coal, using more productive machinery, is inexorable. Intolerable level of dust generated at the face is an indication of inefficient coal/rock cutting by these machines. The federal goverment of the United States paid about 11.7 billion dollars in workmen's compensation to more than 470,000 miners with CWP [2]. Bieniawski and Zipf [3] reported that annual benefit payments were about 2 billion dollars. The enactment of the Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanisms and cutting tool designs.The surveys concerning the utilization of cutting bits and performance of continuous miners in underground coal mines were made in order to have first hand information about bit consumption and coal produ¬ction.Three types of used bits, commonly utilized cutting tools on continuous miners, were collected from different coal mines. The used bits were grouped into symmetrically and asymmetrically worn bits. Distribution analysis for weight loss and conical height loss was done. Details of the results are presented elsewhere [4], here the results are summarized briefly. The analysis shows that approximately 50% of the collected bits have worn asymmetrically, which shows that many bits do not rotate properly during cutting. Analysis of the distribution of bit wear showed that the degree of bit wear varied from one type to another and with mining conditions. On average, the weight loss of the used bits was 4% to 7% with a maximum of 31%. Correspondingly, the loss of the conical height was observed to vary between 11% and 23% with a maximum of 71%. Figure 1 shows typical data associated with some of the used bits."

Jan 1, 1998

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By A. C. Fieldner

"Purpose and Nature of Tests:The rapidly increasing use of motor vehicles and trucks in the United States is creating an entirely new problem in the proper ventilation of tunnels, subways and other confined spaces through which such machines must pass. This problem has become of immediate importance because a tunnel 3,000 ft. long is being designed to pass under the Hudson River between New York City and New Jersey. Another tunnel at Pittsburgh 5,700 ft. long through the South Hills, is already under construction, and a third tunnel, 6,000 ft. between Boston and Past Boston is proposed. It is probably that other tunnels will be started in various parts of the United States in the near future.The ventilation of such tunnels is a serious matter, on account of the poisonous nature of automobile exhaust gases. It not uncommon to read about finding a man dead in his garage. Generally this happens on a cold, winter morning, after he has been running the engine with the doors and windows closed."

Mar 1, 1920

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By Carlton E. Brown

[The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted. in South Africa about 19164/ and more recently in England5/,6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting.]

Jan 1, 1938

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By T. J. Ballard

The Conrad Hill mine vas first opened as a gold mine about 182 and has been operated at various times since then. The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings. The work failed to reveal appreciable copper values or evidence of additional ore deposits.

Jan 1, 1948

By Susan M. Moore

The objective of this study was to evaluate the circumstances leading to fall from equipment injuries in the mining industry. Method: The 2006 and 2007 Mine Safety and Health Administration annual injury databases were utilized for this study whereby the injury narrative, nature of injury, body part injured, mine type, age at injury, and days lost were evaluated for each injury. Results: The majority of injuries occurred at surface mining facilities (~60%) with fractures and sprains/strains being the most common injuries occurring to the major joints of the body. Nearly 50% of injuries occurred during ingress/egress, predominately during egress, and approximately 25% of injuries occurred during maintenance tasks. The majority of injuries occurred in relation to large trucks, wheel loaders, dozers, and conveyors/belts. The severity of injury was independent of age and the median days lost was seven days; however, there was a large range in severity. Impact on industry: From the data obtained in this study, several different research areas have been identified for future work, which include balance and stability control when descending ladders and equipment design for maintenance tasks.

Jan 1, 2009

By K. A. Johnson

Marshall and Bird have published the results of a cooperative investigation by the Bureau of Mines in which they developed a procedure for measuring the agglutinating value of coal.4 As stated in their paper, the procedure outlined was suggested by the early worn of Richters5 and Campredon,6 whose procedures were hurriedly modified to meet the need of an investigation then in progress. Since the publicatien of that paper, further work has been done in an attempt to show how the variables involved affect the concordance of the results, in order that such results may be obtained in different laboratories. Briefly, Marshall and Bird's method for determining the agglutinating value of coal consists in carbonizing an intimate mixture of 10 parts by weight of sand and 1 part by weight of coal in a porcelain crucible at a uniform temperature of 950° C. in a, vertical, cylindrical, electrically-heated furnace. After carbonization, the resultant buttons are crushed in a testing machine and the breaking strengths recorded in grams. The agglutinating value reported is the average breaking strength of 10 buttons. The coal for the test is prepared by crushing to pass a 100-mesh screen. The sand used as a diluent is sized between 40 and 50 mesh sieves with openings of 0.381 icon and 0.279 millimeters, respectively.

Jan 1, 1930

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

By Causey J. Douglas

In 1988, at the request of the Bureau of land Management, the U.S. Bureau of Mines studied part of the 13,460-acre Owyhee Breaks Wilderness Study Area (OR-003-059) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. No mineral resources were identified in the study area during this investigation. There is an occurrence of jasper along Birch Creek and an associated occurrence of zeolite in some tuffs. In the northern part of the study area is an occurrence of bentonitic clay containing less than 40,000 tons. Much of the area is covered by landslide blocks, colluvium, earthflow deposits, and talus, composed of Tertiary-age volcanic rocks. The upper plateaus are capped by Tertiary-age basalt.

Jan 1, 1989

By Keith L. Harris

Real gross national product3 (GNP) grew at a seasonally adjusted annual rate of 4.2% in the fourth quarter compared with a revised 4.3% rate in the third quarter, according to the most recent estimates released by the U.S. Department of Commerce (table 1). Expanding inventories, Government purchases of goods and services, residential fixed investment, and a narrowing of the trade deficit fueled the growth. Significantly reduced consumer demand led to the heavy inventory growth. Almost half of the buildup in inventories consisted of automobiles because consumers reduced purchases when Detroit ceased most incentive programs in late summer. Reduced consumer demand also affected imports, however, and the narrowing of the trade deficit resumed after widening in the third quarter. Nonresi- [ ] dential fixed investment also declined after a strong gain in the third quarter. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 2.9%, the same as that of 1986. However, on a fourth-quarter-to-fourth-quarter basis, the real growth reached 3.8%, the highest growth since 19M, and exceeded the Reagan Administration's estimate of 3.4%. Rising merchandise exports accounted for about one-third of the growth in GNP for all of 1987 and are expected to continue to grow as domestic manufactures benefit from the lower value of the dollar vis-a-vis other major trading country currencies. Consumer demand became a less important factor of economic growth, but employment continued to grow (table 2), and civilian unemployment declined by 0.9 percentage points (December to December) as the industrial sector geared up to increase exports. Inflation, as measured by the fixed-weighted GNP price index, remained low at 3.4%.

Jan 1, 1988

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979