Search Documents

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By R. L. Crosby, L. W. Higley

Magnesium- rich magnesium- aluminum- zirconium alloys in the cast and in the extruded and heat- treated condition were studied to identify the phases present and to determine phase distribution . In cast alloys , two intermetallic compounds were identified : ZrAla by X- ray diffraction ; and Mg₁ Al₁₂ by microscopical observation . Based on microscopical comparisons between the known phases in the cast structures and the phases in the structures of extruded and heat - treated rods , ZrAl₂ and Mg1 , Al12 were identified in the structure of the latter . The presence of these intermetallic compounds in rod specimens could not be confirmed by X- ray diffraction . ZrAl₂ was observed in the structure of extruded and heat - treated rod specimens containing as little as 0.01 weight - percent zirconium . The presence of aluminum restricts the solubility of zirconium in magnesium because of the strong tendency to form ZrAla . This intermetallic compound segregated in clusters of small particles in the matrix of cast alloys , and only slight improvement in distribution was noted when the alloying techniques were varied .

Jan 1, 1964

By J. C. Meeks, C. L. Klingman

An instrument that is sensitive , portable , safe , and low in cost was developed by the Bureau of Mines for detecting helium leaks by comparing the thermal conductivity and flow rate of the atmosphere around the suspected leak against a reference of helium- free air . A vacuum pump pulls the sample gas through a restriction and over thermistor elements , the combined electrical output of which is affected by thermal conductivity and flow rate of the sample gas . Tests showed that the battery - operated Helium Leak Detector was effective and rugged instrument that could be operated safely in explosive atmospheres . The instrument could also detect , but not identify , other gases such as methane , hydrogen , argon , carbon dioxide , and Freon 12 .

Jan 1, 1964

By Maria I. DeRosa

This Bureau of Mines report describes the Automated Breathing Metabolic Simulator and its hardware and software systems with emphasis on the role exerted by the software program subroutines in controlling the hardware mechanisms during the simulation of man&apos;s respiratory and metabolic functions.

Jan 1, 1978

By Stephen C. Tadolini

The anchorage capacity of four types of bolting systems was investigated in two mines with thick coal roofs. In conjunction with the in-mine tests, a simple axisymmetric finite element computer program was developed. Both the field and computer results indicated that thick coal roofs can be effectively supported entirely by the coal member.

Jan 1, 1986

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By W. D. Riley

The Bureau of Mines is conducting research on methods for the rapid identification and sorting of mixed scrap metals and alloys so that domestic scrap resources can be fully utilized. One method, spark testing, is the examination of the pattern of sparks that results when a metal or alloy is ground on an abrasive wheel. This technique requires experienced sorters. Bureau researchers have shown that spectrophotometric methods can be used in lieu of the highly skilled sorter. The spectra of a mild steel, an HSLA steel, several stainless steels, and four nickel-base alloys have been measured. Differences in the spectra that are sufficient for identification are apparent.

Jan 1, 1985

By D. A. Wilson

A laboratory method for processing lead battery scrap has been developed that eliminates virtually all of the S02 emission that normally is produced when a reverberatory or blast furnace is used. The method employs a hydrometallurgical step to convert the PbS04 to PbO and CaS04 by mixing the battery scrap with a slurry of Ca(OH)2. The reaction is exothermic and goes to completion in 2 to 5 minutes at room temperature. The dried product is mixed with a KC1-NaC1 flux and carbon and reduced at 6500 C. A minimum charge ratio of 3 parts of carbon to 100 parts of battery scrap is required for reduction. The process produces lead reductions and recoveries as high as 97.0 and 94.9 percent, respectively. The KCI-NaCl flux is recovered using a standard counter-current water leach followed by evaporation.

Jan 1, 1976

By W. H. Ode, W. A. Selvig

Briefly, this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties. The number of the standard profile with which the maximum cross-sectional area of the button most nearly corresponds is recorded as the swelling index. Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization, it gave indications of having value in measuring free-swelling and coking properties of coals when burned on fuel tests. An opportunity to investigate this occurred when an engineering company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal. Some of these coals gave trouble by swelling excessively and clogging the grate. Samples were obtained, and it was found that the troublesome coals gave radically higher free-swelling numbers than did the coals that performed satisfactorily. Also, it was found that the free-swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the standard volatile-matter test or iron agglutination-value results. The results of the free-swelling test were confirmed by the Subcommittee on Plasticity and Swelling, Coal, a special group of the Subcommittee, under the chairmanship of R.A. Shuman, worked along with the test method. Estberg, Limacher, and Shuman of the Battelle Memorial Institute investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential-type stokers from the swelling characteristics of the coal. Data were presented that also showed that the index was helpful in the selection of coal for industrial underfeed stokers.

Feb 1, 1948

By M. V. HANSEN, Frank PERZ, Edward Thomas, C. H. SEELING

This is the second of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal . Their purpose is to focus the attention of the coal-mining industry on the most - common source of fatalities and injuries in mining coal and to disseminate information that may be helpful in combating the roof - fall hazard . Inasmuch as approximately 85 percent of roof - fall accidents occur in the face region , the importance of analyzing the accident - producing aspects of methods of roof support at the face or lack of method overemphasized . - - cannot be This circular is not intended to be an exhaustive treatise on methods of roof support in face regions but rather is a description of several methods of support that appear to offer distinct advantages with respect to safety and efficient operation .

May 1, 1948

By R. J. Heemstra

A method was developed for calibrating photographic emulsions and retrieving working curves for emission spectrography. The values obtained from a digital readout or a recorder chart of a comparator-microphotometer are converted to light intensity values using an emulsion characteristic curve derived from a quartic polynomial preliminary curve. The characteristic curve, consisting of Seidel transform versus the logarithm of intensity, is split into two cubic polynomials at the zero value of the transform, resulting in eight emulsion calibration coefficients. These methods allow use of the calibration curves even at very small and very high intensities, thus extending the range of analysis. Use of a small computer allows rapid calculations. A computer program was written to formulate, code, and file each working curve along with its statistical error. Proper coding of the input data permits the direct printout of the concentration of the elements under investigation.

Jan 1, 1970

By David C. Minton

This paper describes in detail the cost of equipping and developing the Golden Belt mine, Yavapai County, Ariz. These costs should be typical of the average small gold mine in central Arizona which has been equipped with used machinery a, a minimum of capital expenditure. The conditions of remoteness, transportation, water, and power supply are about average for properties in the Bradshaw fountains and that vicinity. There are several mines in the district in the process of development and several dormant properties that might be opened in the future. The Golden Belt group of claims was taken over by the present management in May, 1931. Although some active development has been carried on in recent years, resumption of work at the old property required entire rehabilitation of the equipment and camp. As the water level had not been reached, there was no problem of dewatering. In the presentation of costs in this paper an evaluation of the cost of equipment and development work as taken over by the Golden Belt Mines, Inc., has been made. Enact data, however, on previous exploration and construction costs are lacking. The total cost of equipping and developing the mine to its present stage has been obtained by adding the disbursements of the present management to the above-mentioned evaluation. These costs do not include the cost of replacing camp, equipment destroyed by fires, of unsuccessful milling experiments, management, or obsolete equipment on the property.

Jan 1, 1933

By Ludwig Schmidt

The petroleum industry has recently shown sucks great interest in the evaporation of crude oil and of gasoline, and in the prevention of evaporation losses that almost daily there is being developed and placed on the market equipment designed especially to reduce these losses. Among the recent developments is a new type of tank roof known as the "floating roof," which practically eliminates the vapor space over the surface of the oil, thus removing one of the chief causes of evaporation. There are at the present writing at least two types of floating roofs which, while similar in fundamental principle, differ mainly in the method of making contact with the inside shell of the tank. One type of floating roof is known as a floating tank deck, and has on its circumference flexible metal baskets containing gravel that .rest against the inside shell of the tank. In the other type of floating roof contact with the tank shell is made by the use of movable buffers or shoes. These are attached to the outer ring of the roof and are pressed against the tank shell by means of springs.

Jan 1, 1923

By G. M. Kintz

From 1895 to 1932, inclusive, 1,0163/ men were killed in and about New Mexico coal mines. Of these, 473 (approximately 47 percent) were killed in the 17 explosions listed in this paper. The second largest explosion of record in the United States, in so far as fatalities are concerned, occurred in New Mexico. The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the State inspector of coal mines of New Mexico. The tables included are complete only with regard to major disasters. The Bureau of Mines considers as a major disaster one in which 5 or more men are killed. A few minor disasters are included, however.

Jan 1, 1934

By E. D. Gradner

During 1924 a number of lives were lost and other men incapacitated by the toxic effects of gases produced in blasting in massive sulphides. In one mine, three men working in a raise were caught by gases from blasting a drift round in massive sulphide on the level. The round in the drift was shot ahead of time and it was necessary for the three men to travel through the gases to the intake air course. Two of the men lost their lives, and the third was injured, apparently for life. Other men at this same mine have been caught in the gases at blasting time and seriously injured. At a second mine, the gases from blasting in sulphides appear to be very dangerous, and it was necessary to send a number of men who were caught in such gases to the hospital. One man who was seriously gassed has not recovered in over a year is time. Another man similarly gassed soon died of influenza.

Jan 1, 1926

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

By Gerald V. Gibbs

As a part of the Bureau of Mines long-range program in asbestos, synthetic asbestiform compounds and minerals were prepared and described. Fundamental structural data on two such compounds are given in this report. Crystallographic data are provided for the synthetic isotypic compounds potassium-lead silicate, K2.Pb4 -Si8021 (I), and lead-aluminum silicate, Pb2. Pb4 .Al2Si6O21 (II). The space group symmetry 14/mmm was assigned provisionally to I and II on evidence of single crystal and piezoelectric measurements. A statistical evalua¬tion of indexed powder diffraction data revealed the cell edtes of I to be a 11.816 and c 7.932A and those of II to be a 11.723 and c 8.044A. The phases are uniaxial with observed refractive indices eD 1.790, an ?D,699 and eD 1.884, cusp 1,807, respectively. The atomic structure of I and II may be based on a complex of chains of silicon-oxygen tetrahedra lying along the c cell edge similar to the type of chain structure postulated by Pauling for scapolite. K2.Pb4.Si8021 and Pb2.Pb4 Al2Si6021 were first described by Geller and Bunting (5, 6)4 as fibrous compounds similar in crystal habit to asbestos. These authors gave powder diffraction data, although no attempt was made to find the cell edges or to index the powder diffraction patterns. Later, Shell and others (9) conducted a crystallochemical study of these fibrous silicates in search of a substitute for strategic asbestos. Their single crystal data revealed K2.Pb4 -Si8021 to be tetragonal body-centered with cell edges a 11.66, c 7.95 A. Pb2.Pb4 Al2Si6021 was concluded to be isotypic with K2.Pb4 -Si8021 on the basis of similar powder diffraction patterns, chemistry, and physical properties. No attempt was made, however, to index the powder diffraction record nor to determine the appropriate space group of either compound.

Jan 1, 1962

By D. S. Kingery

Recent Federal coal-mine inspections have revealed some good and some definitely hazardous practices and systems for transporting; handling, and storing lubricants in and about coal mines. Improper storage or handling of. lubricants in coal mines has caused disastrous mine fires or, by supporting combustion, has made fires from other sources more difficult to fight. Careless handling of grease and oil around electrical equipment wastes much oil and permits entrance of grit and foreign substances into the working parts, which causes excessive wear and increases the possibility, of electrical ignition.

Jan 1, 1943

By F. D. Cannon

"In metal and nonmetallic mineral mines during the 15-year period 1911 to 1925, 30.17 per cent of all fatalities and 16.57 per cent of all injuries were caused by falls of rock or ore from the back or roof or from the wail; 1.24 per cent of the fatalities and 11.05 per cent of the injuries were caused by rock or ore while loading at the working face; 6.66 per cent of the .fatalities and 2.49 per cent of the injuries resulted from men falling down 3 chute, winze, raise, or stope; and run of ore from chute or pocket caused 1.48 per cent of the fatalities and 1.93 per cent of the injuries.3 Hence, accidents due to falls of men and material caused. 39.55 per cent of the fatalities and 34.05 per cent of the injuries in these mines. Accident prevention can best be assisted by each company's preserving complete records of accidents classified according to cause and rate per thousand or 10,000 shifts. A systematic method of recording accidents and the employment of graphs or charts will be helpful to the company safety department in analyzing the cruses of accidents. The purpose of this publication is to analyze data on accidents caused by falls of men and material in metal -mines of the United States, and to suggest methods of preventing or reducing such accidents."

Jun 1, 1929

By R. Blickensderfer

An impact wear testing machine was devised by the Bureau of Mines that simulates the repeated impact conditions encountered in large milling and grinding operations where breakage and spalling are problems. The apparatus provides data on materials that may help in the design of alloys with improved resistance to deformation, spalling, and breakage. The test blocks are 2 in thick by 6 in by 8 in. Impacts are produced by dropping 3-in-diam balls weighing 4 lb from a height of 10 ft. Tests were run until breakage occurred or to a total of 100,000 impacts. Four types of failures of the test block were observed: (1) cold flow of the bulk material by plastic deformation, (2) flaking of the surface in the impact region, (3) spalling of the block to form a crater in the region of impact, and (4) breakage of the test block into two or more major pieces. The effects of composition, heat treatment, microstructure, and hardness on types of failure are discussed.

Jan 1, 1983