Search Documents

In 2005, 14,666 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA).1 Almost half (48.5%) were sand and gravel mines, followed by stone mines (30.6%), coal mines (14.1%), nonmetal mines (5.0%), and metal mines (1.8%).

Jan 1, 2008

By J. M. Kuchta

Concentrated hydrogen peroxide (H202) is a highly reactive oxidizing agent that liberates heat when it decomposes. The heat liberated may be sufficient to ignite combustibles with which the peroxide comes in contact. For this reason, concentrated hydrogen peroxide should be handled only by personnel familiar with its many unique properties.6 Hydrogen peroxide is used as a bleaching agent in the manufacture of textiles; this is its major single use in the United States. It is also employed as a reagent in chemical synthesis, as a source of free radicals to start polymerization, as a foaming agent in the manufacture of porous substances, and for its effect on biological processes. Moreover, highly concentrated hydrogen peroxide is a compact source of energy that can be utilized both as a monopropellant and as the oxidizer in a bipropellant system, During World War II, large quantities of highly concentrated hydro- gen peroxide were used as propellants, particularly in Germany. Since then, production of the peroxide has increased rapidly; in the United States alone it has more than doubled since 1950.7 Because of its widespread use, increasing interest has been shown in the hazards of handling the high- strength peroxide.

Jan 1, 1961

By D. P. Lindroth

The Bureau of Mines is engaged in research on ground probing radars for detection of geologic hazards in advance of mining. Penetration distances and interpretation models depend on the dielectric properties and wave propagation characteristics for coal measure stratified media. Relative dielectric constants and dissipation factors were measured under ambient conditions for Pittsburgh Seam coal measure rock over the frequency range of 20 to 100 MHz by the susceptance-variation method. The rock types measured were representative sedimentary rock located above the Pittsburgh Coal Seam. Extreme values for the computed attenu-ation distance ranged from 1.7 m at 100 MHz for siltstone to 230 m at 20 MHz for a particular limestone.

Jan 1, 1984

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

By R. Hogg, T. F. Dumm

"Abstract - With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents, and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and subsieve particle size analysis of the specific gravity fractions, a complete size specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.IntroductionTraditional gravity separation techniques such as jigging, heavy media and water-only cyclones, shaking tables, etc., have been used to remove impurities from coal ranging in size from about 15.cm (6 ln.) to about 150 µm (100 mesh). The coal washabilty or float-and sink technique ls a well-established procedure for determining the optimum extent to which a coal can be cleaned by such physical separation methods. Because of the desire to recover even finer coal fractions by gravity separation techniques, there is a need to extend the coal washabillty analysis into the ultrafine range. The purpose of this paper ls to describe some of the significant factors that influence fine particle specific gravity separation. Washability analyses have been performed on three ultrafine ( <10 µm) coal samples representing three general mining districts in Pennsylvania. Results of these analyses indicate that the washabillty technique can be successfully applied to ultrafine particles when proper care ls taken."

Jan 1, 1988

By D. Bienstock

Using a nitrided fused-iron catalyst, the Bureau of Mines investigated the Fischer-Tropsch reaction in the oil-circulation process. The nitrided iron was quite stable and permitted the longest run obtained thus far in the oil-circulation process without the need for reactivating the catalyst--3,700 hours of operation. The effects of several operating variables--temperature, pressure, gas-recycle ratio, space velocity, synthesis-gas composition, and synthesis with and without reflux of oil to the reactor--on the production of oxygenates were studied. The importance of removing reflux oil and of high gas recycle in increasing the oxygenate content was shown. A finished gasoline containing 28 percent by weight alcohols was produced. The research octane number (RON) was 92.9 clear, increasing to 98.5 with the addition of one milliliter of tetraethyl lead (TEL). INTRODUCTION The Federal Bureau of Mines has been engaged since 1944 in a research and development program on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a "synthesis gas"--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va., and the synthesis of gasoline by catalytically reacting carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

Minerals are a fundamental component of the Nation" material and economic base. Without a continuous supply of minerals to meet growing and changing needs, the basic character of our society would be very different. The importance of minerals to the United States was reemphasized by the Congress in I970 when it enacted the Mining and Minerals Policy Act, which stated that it is the continuing policy of the Federal Government in the national interest to foster and encourage private enterprise in (I) the development of economically sound and stable domestic mining, minerals, metal and mineral reclamation industries, (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial, security and environmental needs, (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral recources, and (4) the study and development of methods for the disposal, control, and reclamation of mineral waste products, and the reclamation of mined land, so as to lessen any adverse impact of mineral extraction and processing upon the physical environment that may result from mining or mineral activities.,.

Jan 1, 1977

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By R. M. Santmyers

"Quartz and silica not only occur in diversified forms in nature but find a multiplicity of uses in industry. The purpose of the present paper is to assemble brief summaries of the many widely differing industries engaged in the production and preparation of these minerals in their principal commercial forms. Due to the scope of the subject it was though advisable to divide the paper into three parts. Part I deals with the subject of quartz and silica in general. It also contains a flow sheet of silica from deposit to consumer (fig. 1). Part II covers the uses and other economic factors of quartz, quartzite, and sandstone, the varieties of silica found in consolidated form. Part III deals with sand and miscellaneous silicas such as tripoli and diatomite. A chart showing the major ramifications of these industries is presented herewith as an introduction to the more detailed discussion that follows.For a more intensive study of many branches of the quartz and silica industries the reader is referred especially to Bulletin 263 of the United States Bureau of Mines, Technology and Uses of Silica and Sand by W. M. Weigel. For annual statistics relative to silica and its products in the United States he is referred to the annual chapters of Mineral Resources of the United States, entitled ""Silica,"" ""Sand and Gravel,"" and ""Abrasives."" With respect to diatomite reference is made to Diatomite, by Paul Hatmaker, recently issued by the U. S. Bureau of Mines as Information Circular 6391. In preparing this paper the author has drawn freely from these sources as well as Marketing of Metals and Minerals, by J. E. Spurr and F. E. Wormser; Non-Metallic Minerals, Occurrence, Preparation and Utilization, by Raymond B. Ladoo; and Abrasives - Part I, Siliceous Abrasives, by V. L. Eardley-Wilmot, Report 573, Mines Brand, Department of Mines, Ottawa, 1927.Acknowledgment is also made to the Foote Mineral Co., which has published in Foote-Prints (vol. 2 of 1929 and vol. 1 of 1930), comprehensive reviews of the uses of crystal quartz in the optical industry and as piezo¬electric crystals.The various forms of silica have attracted attention from the earliest times, and the water-clear crystallized variety was known to the Greeks as""krystallos"" (clear ice), being supposed by them to have been formed from water by the intense cold of the Alps; hence the name ""crystal"" or more commonly ""rock crystal,"" applied to this variety. The name quartz is an old German word of uncertain origin used by G. Agricola in 1529.Silica or silica dioxide (Si02) either free or in combination with other elements constitutes 59.08 per cent of the lithosphere, and quartz alone represents fully 12 per cent` of all rocks. Next to the feldspar group quartz is the most abundant mineral in the earth's crust; and it appears in a greater number of varieties and modes of occurrence than any other mineral. Silica or quartz occurs in crystalline, cryptocrystalline, microcrystalline, and amorphous forms. The most common, however, is the crystalline form, which occurs as three minerals, quartz, tridymite, and crystobalite, and of these three tridymite and crystobalite are quite rare in nature."

Aug 1, 1931

By R. O. Dannenberg

The Bureau of Mines conducted laboratory investigations with the objective of developing an alternative process for recovering cobalt and copper from complex sulfide concentrates. Processes currently used depend largely upon precipitation techniques to remove impurities and recover cobalt from sulfate liquors prepared by oxidative pressure leaching of the sulfide concentrates. The Bureau conducted bench-scale research on a process for treating cobaltite concentrates, comprising (1) oxidative pressure leaching, (2) jarosite precipitation followed by H202 oxidation and pH control to remove iron and arsenic, (3) copper solvent extraction with a mixed hydroxyoxime-amine extractant, (4) copper electrowinning from recirculating acidic strip liquor, (5) selective cobalt extraction from copper solvent extraction raffinate with a phosphinic acid extractant, and (6) electrowinning of cobalt from a recirculating weak acid strip liquor. Overall cobalt and copper recoveries were 91.7 and 84.1 pct, respectively. Electrowon products assayed 99.8 pct Co and 99.89 pct Cu.

Jan 1, 1987

By W. H. Young

MOST OF THE key items in the bituminous-coal and Lignite industry declined in 1954 compared with 1953. Production, consumption, exports, average value per ton, men working, and days worked all declined; however, in the field of mechanization, the percentages mechanically loaded, mechanically cleaned, mined by auger, and mined by stripping all increased, as did production per men per day. Production.-The output of soft coal in 1954-391.7 million tons- was 14 percent less than the 457.3 million tons produced in 1953. The lower production in 1954 was due largely to a sharp reduction in consumption in the United States and to a drop in exports.

Jan 1, 1958

By William H. Lewis

This paper describes the Bureau of Mines efforts in the research and development of a new and innovative mine lighting system which is based on fiber optics technology. The new lighting concept offers significant advantages over conventional systems in the areas of both safety and long- term maintenance costs. An overview of Bureau research into the problems and limitations of present-day mine lighting systems is also presented.

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By Irving Hartmann

The Experimental Coal Mine of the Bureau of Mines has served principally as a valuable and unique testing laboratory for studies of the explosibility of coal dust and mine gas; studies of the numerous complex and interrelated chemical and physical factors that govern the ignition of coal dust and the propagation of mine explosions; and studies designed to develop measures for preventing explosions or reducing their destructive effects. These researches, coupled with educational efforts by the Bureau of Mines and enlightened safety consciousness in the mining industry, had fruitful results. This is evidenced by the remarkable reduction in the frequency of major coal-mine explosions and the number of fatalities from explosions since the Bureau of Mines was established. Despite this progress, further important unresolved problems arise; these are due in part to changes in mining conditions and methods, which have brought about increased production of fine coal dust in highly mechanized operations. To solve the new problems, research must be continued without interruption. The results of many very recent and current studies in the Experimental Coal Mine are summarized briefly, and pertinent studies by European mine-safety-research organizations are listed.

Jan 1, 1957