Search Documents

By William Adamson

Precise and data driven methods of predicting and modelling blast induced vibration intensity are created and applied under field conditions on a routine basis today. These models are fed with controlled field measurements of vibration pulses generated by controlled charges under known geometric conditions. With such models blasting and geomechanical engineers can estimate vibration intensity at established critical points in mine bench geometry (surface mining) as well as within semi-permanent crown and rib pillars (in underground mining).Damage to bench walls and destabilization of large-scale geomechanical structures can be partially attributed to high intensity blast induced stresses on the rock mass and structures that define important features such as safety catch berms and haul roads. In the underground environment, weakening of critical pillars in block caving or Long Hole Open Stoping(LHOS) operations may lead to ore sterilisation. Blast vibration intensity can be linked with physical alteration in critical rock mass volumes within themine. Often the potential for vibration damage is estimated by the calculation of a critical value of vibration intensity, derived from a consideration of laboratory measured rock matrix properties. Efforts to confirm the accuracy of these estimates of critical vibration level include post blast excavation photography as well as the visual examination of rock mass, pre-and post-blast, using video camera observation of the walls of purpose drilled observation holes. These methods clearly indicate a change in fracture state due to the blast induced vibration, however further modelling of geomechanical stability will benefit if seismic measurement data can be interpreted in terms of geomechanically relevant strength parameters. This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

By Patrick D. McLaughlin, C Fordham

"The project outlined in the accompanying paper was to densify beach sands on the pond side ofa tailings dyke to the strength required for future dyke construction, This was to be achievedthrough the detonation of relatively small explosive charges in the sand to cause settlement intoa denser state."

Jan 1, 1992

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

Secondary or boulders blasting is a regular feature of quarrying operations in Pakistan, especially in cement and stone crushing industries. The main reason for secondary blasting is the production of a large number of boulders during the production blast. These boulders are larger than the feed hopper of crushers and require further breaking. The complex geometry of boulders, relative lack of restraining burdens, and the availability of number of free faces make this kind of blasting more hazardous than production blasting. Secondary blasts have generally unpredictable results and may cause flyrock, airblast, and over-crushing of rock material. Thus, it is essential to have an appropriate amount of explosive charge/powder factor, and for it to be properly distributed in the blast hole. The greater the amount of explosive over the required amount, the more violent is the blast, which will result in more flyrock, airblast, and excessive crushing of boulders.

Jan 1, 2012

By Ankit Jha, Sudarshan Rajagopal, Purushotham Tukkaraja

Geologic structures are one of the crucial parameters in blast design. Structural geology and rock properties influence drilling patterns, blast layout, and initiation systems. A comprehensive understanding of structural characteristics is essential to achieve the desired blasting objectives. This paper aims to identify geologic features in a bench using images obtained from the drone. Images obtained from mine site are annotated for geological features such as faults and joints. Semantic segmentation of images is achieved using an encoder and decoder structure available in the machine-learning pipeline. The encoder consists of initial convolution and pooling layers to capture essential features of the geology and rock patterns from two-dimensional RGB images. Batch normalization is used to put all the features on the same scale. These images are then inputted as training data for the machine-learning algorithm. Machine learning model is trained on sub-section of interest to achieve reasonable accuracy. Initially, 1000 best annotations were used to train the model and additional samples were added later to achieve more accuracy and avoid iteration of machine learning model in wrong convergence. After the model achieves reasonable accuracy, it is used to recognize geological features on new data. Geological features identified on the new data can be used by the blasting crew in blast design and keeps the geological maps updated that can help the geotechnical team.

By Per-Anders Persson

TIGERWIN, now on CD, is a user-friendly personal computer code (running under Windows) which determines the detonation and expansion state of an explosive from its known chemical composition. TIGERWIN is intended for users in the mining and commercial explosives industry who do not routinely program or run Fortran codes. The code allows the user to open a window on the computer screen and enter the initial density and the weight percentage composition of an explosive, ingredient by ingredient. Alternatively, the code can balance the composition with one or more ingredient percentages fixed, while proportionally adjusting the others automatically to give a total of 100%. The equation of state and its parameters can be user-selected from several proven and tested versions of the BKW, the JCZ, and the ideal gas equations of state. TIGERWIN allows the user to select several options for different additional calculations, such as determining the constant volume explosion, the Chapman-Jouguet (C-J) point, the detonation Hugoniot, the expansion isentrope from the C-J point, and point calculations with selectable specific volume and temperature. Additional options include calculations of detonation data with one or more ingredients partially reacted, assuming either temperature equilibrium between reaction products and unreacted material, or keeping the unreacted material “cold” at the initial temperature. Thus the code can run both ideal and non-ideal detonation calculations. The code automatically saves the input and output files in a separate directory for future reference. The output from several calculations can be displayed and printed in the form of a comparison table. In it, the key results of up to five calculations with different explosive compositions can be compared. The results from an individual calculation can be displayed graphically and printed with expansion work, pressure, or temperature as functions of specific volume. A complete listing of the details of the calculation results, similar to those from the original Fortran Tiger calculations, can also be displayed and printed. No computer experience is required to run the code and workshop participants are encouraged to bring in their own formulations to try out on TIGERWIN

Jan 1, 2000

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control

Feb 1, 2020

By Ruilin Yan, Kameron Ray

This paper reports a simple approach to model the waveform change due to travel distances based on the field measurement. A linear interpolation is used to estimate the waveform at a distance from two vibration waveforms recorded at two different distances. The resulted waveforms are compared with actual recorded waveforms at the point in both time and frequency domains. It shows that the proposed method to estimate the waveform change yield reliable results. The advantages of the proposed method are that it does not require assumptions that a transfer function does and that it is based on purely the measured waveforms that are encoded with in-situ rock properties. The method could be more reliable for far field seismic waveforms and could be an approximation for near field waveform estimation.

Jan 1, 2014

By Carlos Pañura, Michael Geldres, Alejandro Rojas

The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration.

Feb 1, 2020

By M. Gebhardt, J. Johnson, S. Rosenthal

The use of presplitting applications in an underground mine setting is a method of reducing overbreak in the rib and back when blasting occurs. Presplitting performed at the Underground Mine Education Center (UMEC) on Montana Technological University’s campus in Butte, Montana showed a dramatic decrease in the amount of overbreak incurred in the blasting process. Application of the presplitting technique occurred after presplitting presentations at ISEE in San Antonio. Presplit testing consisted of drilling perimeter holes closer together than production holes and loading perimeter holes with a combination of specialized presplit explosive and packaged emulsion with electronic detonator initiation. The ideology was to shoot the perimeter row first, to create a fracture around the perimeter, so when the main production round is shot there is less shock exerted on the surrounding walls due to the pre-fractured perimeter rock. For the test performed, the back ended up with 83% of total holes resulting in half barrels representing a remarkable result. The right rib ended up with one half barrel visible before muck was removed while the left rib did not have any half barrels visible due to a clay seam being in very close vicinity to the perimeter row. The first test blast was a great start encouraging future work on presplitting applications in the UMEC. Additional testing will continue with different combinations of perimeter hole spacing, the addition of a buffer row along the ribs, and varying loading techniques to determine the most effective presplit method for the rock type of the UMEC. Detailed test results and loading configurations will be provided in the paper.

Jan 1, 2024

By John C. Adams, Darrel D. Porter

After conventional drill and shoot methods were determined to be unfeasible due the fractured nature of the ground, a "coyote" blast was designed to produce 250,000 tons of rock from Rhone-Poulenc's Maiden Rock silica pit located near Butte, MT. This paper will cover the design and excavation of the explosive drifts, the placement and priming of 190,000 pounds of explosives, and the backfilling of the drift to provide confinement of the charges.

Jan 1, 1993

By Stuart Brashear, Steven Bell, Donald Smith

This Limestone site required the removal of a bench containing high quality rock located in close proximity to sump and pit pump. The sump and associated electrical box were below the bench that needed to be blasted and located only 70 feet (21.33 meters) away. It was proposed to blast material needed without moving or disturbing the pump or electrical junction box. The area to be blasted was flown with a drone and stitched into a 3D orthographic model. Proprietary blast design software was used to create a blast design solution that would allow for a series of blasts that would provide required fragmentation and muckpile development and not disturb the sump or electrical box. A drill patten was created for each blast using the burden heat map and 3D face profiles created from the 3D orthographic model. Timing contour lines and muckpile displacement predictions were used to create timing sequences for proper face movement away from the sump and electrical box. The shot designs were laid out with a GPS system to insure hole location accuracy. All holes were remeasured for proper face burdens using the 3D model and Boretrak®® data collected after drilling operations were completed to insure hole locations were within face burden tolerances as derived by the burden heat map. After each drill log was reviewed, a charge loading scenario was created for each hole. The timing design created, for each shot and was reviewed and adjusted as needed with regard to desired muckpile displacement away from the sump and electrical box. Blasting results were satisfactory, with fragmentation and muckpile development consistent with the calculated throw from the blast model, with no rock hitting the pump or box and no rocks striking the sump water and disturbing the pump motor.

Jan 21, 2025

By Estefania Aramayo, Jhon Silva, Todor Petrov

Blasting is one of the most critical activities in a mining operation. Nowadays, many quarries have to follow a considerable quantity of environmental restrictions that drive the need to improve the conceptualization, design, procedures, and execution of the blast to comply with all regulations. Airblast is one of the variables required to control when blasting. Airblast is an unwanted side effect of blasting. Airblast is defined as an airborne shock wave resulting from the detonation of explosives. Traditional methodologies used for assessing the overpressure produced by the airblast are based on empirical approximations that require the collection of a series of produced airblasts before they can be used as a predicting tool. Once the data is available, regression analysis methodologies are used to find the constants of empirical laws that, in most cases, establish the relationship between the distance and the weight of explosives used in the shot (scaled distances laws). If using the traditional methodologies, the quality, and representativity of the scaled law established for a particular project are determined in terms of the correlation coefficient; in most cases, the models and their use as a predicting tool are questionable (very low correlation values).

Feb 6, 2023

By Julia Creasey, Natalie Hodgson, Claire Ward, Craig Davies, Helen Sarginson

"Emulsion explosive producers are attempting to lower the cost of emulsion production by using lowquality ammonium nitrate in emulsion formulations. Low quality ammonium nitrate contains additivessuch as anti-caking agents and crystal modifiers which contaminate the emulsions causing instability. This presents a need for an effective emulsifier that will maintain emulsion stability under thesechallenging conditions."

Jan 1, 2017

By A. Lindo, M. Held

The formation of NOx fumes is an undesired occurrence and is dependent on a variety of variables. Methods for detection of such fumes with blast analysis tools are available using color schemes for grading, but no quantification tools to measure concentration and cloud totals exist today. In cooperation with DIRS (Digital Imaging and Remote Sensing Laboratory) at RIT in Rochester, NY, Austin Powder has been looking for methods and techniques to identify and quantify total amounts of NOx by capturing cloud activity via a video feed from a drone in combination with measuring NOx and subsequent cloud modeling (i.e., plume segmentation). To accurately measure fume events, Austin Powder and the RIT team have been collaborating in performing small scale blasts at an Austin test facility and then transferring knowledge learned to full scale blasts at customer sites. The collected data will allow to identify any relationships between the total amount of explosives used and the quantity of NOx produced. The analysis of the total amounts of NOx and identification of blast areas those fumes originate from will help to better understand key factors that contribute to their occurrence as well as to quantify the severity of such events. By quantifying the magnitude and concentration of fumes generated by non-ideal detonations, the blasting technique can be optimized to minimize unwanted environmental effects and improve public perception of blasting as a necessary component of societal progress

Jan 1, 2024

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025

By Marilena Cardu, Mauricio Dompiri, Jacopo Seccatore

Blasting in geological bodies is an industrial process acting in an environment characterized by high uncertainties (natural joints, faults, voids, abrupt structural changes), which are transposed into the process parameters (e.g. energetic transfer to rock mass, hole deviations, misfires, vibrations, fly-rock...). The approach to this problem searching for the “optimum” result can be ineffective. The geological environment is marked out by too many uncertainties, to have an “optimum” suitable to different applications. Researching for “Robustness” in a blast design gives rise to much more efficiency. Robustness is the capability of the system to behave constantly under varying conditions, without leading to unexpected results. Since the geology varies from site to site, and often from bench to bench on each site, setting a robust method can grant better results in varying environments, lowering the costs and increasing benefits and safety.

Jan 1, 2011

By Christopher Laughton

A new underground laboratory is under construction at the recently closed Homestake Gold Mine, Lead South Dakota, United States of America. The Deep Underground Science and Engineering Laboratory is designed to meet the needs of an international group of scientists and engineers interested in conducting fundamental and applied research at depth in the Earth’s crust.

Jan 1, 2011