Search Documents

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By Liping Yu Che, Xiaotie Wang, Mingli Cao, Jizu Yongfu Yuan

"It is difficult separating fluorite from Ca, Ba, Si intergrowth minerals than simple from Si, using common reagents such as combination of oleic acid or paraffin soap and water glass, but the finest quality fluorite concentrate whose grade is over 96%F must be required in chemical plant.This paper studies the flotation process of native fluorite from calcite, barite and silicate minerals whose flotation properties is similar to fluorite, using new effective collector H602 and new depressor S602 that is cheaper in cost, and describes the flotation properties. In order to determine optimum flotation separation condition, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents on flotation were investigated and the flotation result was provided by oleic acid collector and the results of collector H602 were compared with those of collector oleic acid in the test. The test result of ore samples shows that at moderate pulp pH values (10.5-11.5) and other moderate technical conditions, the fluorite mineral can be obtained by new reagents and the rational reagents combination. The conclusion is 98%F of fluorite concentrate can be obtained, using the combination of H602 and S602 and only 5 steps in techniques. The paper discusses the mechanism of the flotation separation of fluorite mineral from intergrowth minerals."

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003

By R. L. Pascual, W. J. Whiten

"The froth flotation process is not well understood. Both flotation models, and the parameters used to describe the stream flows are not well defined. They in fact vary considerably in different applications. This creates difficulties is designing a simulation program suitable for use by plant personnel, consultants, and researchers. In addition to simulation, an effective simulation program can be expected to provide a range of other services.This paper shows how a process circuit simulator can be designed with sufficient flexibility to satisfy these needs, and discusses some of the additional services.OVERVIEWThe development of a simulation program for froth flotation circuits faces several challenges as flotation models and the associated stream descriptions are not well defined. There is little agreement on the best form for a flotation model, or on how the plant streams should be defined.In addition to simulation, a flotation simulator is generally expected to provide other services such as data input, data reconciliation, model fitting, and accuracy estimation. Additional services may also be needed beyond what might initially be envisaged. A summary of some of these possibilities is included.To apply simulation to a flotation circuit it is necessary to develop a flotation cell model, for instance based on the general outline given in the appendices. Experimental data, usually from the plant, is needed to determine cell model parameters. This is generally done by first undertaking data reconciliation to determine if mass flow constraints are sufficiently closely satisfied. At the same time the data is inspected for outliers that might bias subsequent calculations. Next the data is fitted to a model to back calculate ore characteristics. If there is sufficient agreement between the fitted model and the data, the model can then used to make predictions of the effect of changes to the plant. The changes, that the simulation shows are beneficial, can be applied to improve plant performance"

Jan 1, 2003

By P. Harris

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Ltd. Kyushu Metal Industry Co., Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

"Actually, the recovery of valuable metals such as iron, aluminium and copper is a nowadays practice in factories dealing with the processing of scrapped automobiles (Harder (WERG); Koga et al., 1997). This process has reach a recycling rate of about 75%, and generates a huge volume of waste (including cottons, sponge, plastics, rubber, etc…), locally known as “shredder dust”, which is commonly dumped on landfills; its recycling is either unsatisfactorily or not yet performed (Keller and Schebdat, 2000).The saturation and depletion of valuable disposal sites in the not-so-distant future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry.To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of a calibrated (–80+5mm) shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-weight materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively. A sedimentation tank is used to recover the light-weight materials deported in the heavy fraction stream."

Jan 1, 2003

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003

By Johan F. W. Kock

"Hearing loss due to excessive noise exposure is the most prevalent industrial disease. It is ranked on the World Health Organization’s (WHO) priority list for major work related injuries. Uncontrolled noise not only has a physical effect, but is also a psychological hazard affecting the performance and well being of man. Noise induced hearing loss (NIHL) is irreversible, yet it is preventable. The first defence against noise (noise control engineering) is a high priority in the mining industry. Second defences should be a last resort when the engineering control of noise is inadequate. Hearing conservation programs and the use of conventional hearing protection devices seem to have failed in the prevention of noise induced hearing loss. If compensation payouts that quadrupled in the past ten years are used as a barometer for the success of existing hearing conservation programs, then new strategies and technologies need to be investigated. The best practice Hearing Protection Device (HPD) may be seen as the minimum standard for second defence noise control.Conventional hearing protection is widely applied, but also misused in the industry as well as in the mining sector. Empirical research results, ownership, general attitudes of workers as well as qualitative aspects will be explored. The paper provides reasons, evidence, case studies and strategies regarding the best practice hearing protection philosophy (the Noise Clipper Model) as implemented in the Implats Mining Group. Worldwide tendencies towards custom-made HPD’s, findings that indicate improvements in hearing conservation programs and finally the successful application of Custom-made Hearing Protection Devices, will be outlined."

Jan 1, 2003

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Huge electrochemical investigations have been performed on Technical faculty in Bor (Serbia) which main goal was the clarification of the copper sulfide minerals behaviour in hydrometallurgic and flotation processes. Modeling of these processes was a part of the effort for better understanding of the reaction mechanisms.The consideration of electrical analog circuit and mathematical model of processes at interfaces copper sulfide/electrolyte (CuS/(CuSO4+H2SO4), Cu2S/H2SO4 and CuFeS2/H2SO4), based on studies of the overvoltage – time transients, will be presented. The transients were obtained using single pulse galvanostatic method and electrochemical cell with standard three electrode assembly. In that goal it was developed an original system for computer measurements that enables the application of several methods for electrochemical investigations (galvanostatic, potentiostatic, cyclic voltammetry, electrochemical impedance spectrometry etc). The system was tested and adjusted using commercial electrochemical equipment made by AMEL, Milano.In the first stage of consideration the different equivalent electrical circuits have been tested by computer programme OrCAD 9.2 in order to identify the circuit with responses equivalent in shape to experimentally obtained ones. In that way it was established a configuration of an analog electrical circuit for investigated electrochemical system. That phase enabled only very rough determination of values of circuit components and their relative ratio.In the second stage the method for determination of all elements of electrical analog circuit is described. It is based on mathematical consideration of a given circuit on one hand, and valves of the overvoltages at selected times, obtained from charging and discharging parts of galvanostatic transients, on the other."

Jan 1, 2003

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Wang Xiaotie, Yu Yongfu, Che Liping, Zhang Fuguang

The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.

Jan 1, 2003

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

"Separation in Froth (SIF) is a process for the separation of mineral particles during their descent downwards through a moving froth layer, generated on the surface of water or some other liquid media by means of a bubble generator and frother. Due to the special operation principles of SIF it is possible to separate mineral particles that are about 10 times coarser than the optimal particle size for conventional flotation. In this paper the performance of the SIF technique is presented in the separation of apatite, calcite and silicate minerals from various industrial sources, based on tests with laboratory and pilot plant-scale SIF machines. Basic laboratory test results of the flotation of pure diamonds are also presented.It was shown that calcite, apatite and diamonds with particle size up to about 3 mm can be successfully floated with SIF at high recovery and grade, provided that the degree of liberation is sufficiently high. Coarse calcite (+0.25-2.8 mm) was concentrated with reverse SIF in one flotation step at 87% recovery with better than 99% grade. Apatite particles coarser than 0.2 mm are not well floated in the conventional flotation circuit leading to high P2O5 content in the coarse size fractions of flotation tailings. On the contrary, SIF is capable of recovering such coarse particles at high recovery. However, P2O5 content of the SIF tailings starts to increase at about 0.7 mm due to insufficient liberation of apatite. At higher particle size the lack of hydrophobicity of apatite particles is also likely to lower the recovery.The pilot plant testwork showed that SIF can be successfully used at operating plants not only for preliminary upgrading of the feed of conventional flotation, but also for producing final grade calcite concentrate (>99.5%) from the screen overflow or from the cyclone underflow in a particle size range up to 1 mm. It was particularly promising that the separation took place in one SIF flotation step, instead of several stages of the conventional flotation circuit, with over 90% calcite recovery. The specific capacity determined with the 1 m2 pilot plant unit was approximately 30 t/m2h. Simultaneously the consumption of chemicals was significantly lower than for conventional flotation."

Jan 1, 2003

By Dave Deglon

"The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomates for the mining industry. The WCMPF consists of academics and Technical Officers in the Departments of Chemical Engineering of the three tertiary institutions. The Technical Officers are usually metallurgists, with several years of industrial experience. The main objective of the Technical Officers is to improve the practical education of mineral processing students. In addition, the Technical Officers are responsible for organising an annual mineral processing student field trip for students from all three tertiary educational institutions. In recent years the WCMPF has embarked on a number of additional initiatives aimed at improving the quality of mineral processing education. These include the development of several new pilot plant practicals, an initiative in pyrometallurgy, the introduction of novel ‘end to end’ or ‘integrated’ practicals and the use of mineral processing simulation packages to complement the practical training.The WCMPF has been functioning for well over a decade and, by virtue of this, might be considered a successful collaborative educational initiative. The WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. During this time period, the WCMPF has gained a body of internal knowledge which might be of benefit to other educational institutions, viz."

Jan 1, 2003

By Daniela Venter, Stephen Chryssoulis, Ken Stowe

"A sampling campaign was conducted at Kemess in order to identify and assess the chemical and physical factors, which control free gold flotation kinetics in the rougher and cleaner circuits. The rationale behind this approach was that accurate knowledge of the parameters affecting free gold flotation kinetics, can be used to determine how to accelerate free gold flotation. Collected samples were composites of 5-6 cuts over a four-hour period, at steady plant conditions.In the rougher circuit, coarser equidimensional gold particles floated ahead of the finer grained and the flaky gold. Sulphur followed by molybdenum and to a lesser extent silver enhanced gold flotation kinetics, while hydroxyl followed by carbonate ions induced depression."

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003

By Wayne I. van Drunick

"Energy balance modeling has recently been shown to be a competent tool in the estimation of SAG mill discharge rheology. Work performed by van Drunick and Moys (2001) validated the ability of an energybalance filter to estimate the slurry density from an operating SAG mill. The importance of rheological data is highlighted by several authors who show the effects on load behaviour and thus mill performance. Energy balance models were developed to account for the dynamic energies in the mill discharge sump. The models then made it possible to infer the mill discharge density. A sampling campaign was performed and the errors from the sump energy balance were within tolerable limits.Since the initial results were published, it has been decided to further develop the modeling techniques in order to focus on balancing the energies around the entire mill. The critical measurements for the energy balance will be the temperatures of all the streams entering and leaving the mill, including energy losses to the environment. Metso’s OCS© (Optimising Control System) currently controls the 3 SAG mills at Anglogold’s Mponeng Gold Plant (South Africa). The OCS has built-in Kalman filtering tools to effectively handle variances and noise in the models and the mill circuit data respectively. The new models are therefore constructed in the OCS platform, and will be run in parallel with Metso’s current modeling and filtering systems. The work is a collaborative effort between Anglogold, the University of the Witwatersrand and Metso. The benefits of energy modeling, compared to mass modeling, are that energy data are more accurately measurable than mass data. The inferred mill parameters can therefore be improved provided that a competent set of models is produced to process the (accurate) thermal measurements."

Jan 1, 2003

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"During 2000 Mintek Developed the PlantStar plant wide control platform for the minerals processing industry. The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.Processes with long dead times, like a feed belt to a mill, are difficult to control. The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.Often there are more variables on a plant that need to be controlled (process variables) than there are variables to control them with (manipulated variables). Process constraints are often reached and violated. Safety control loops are necessary to prevent constraints being reached. The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. It continuously perturb the solids feed rate to learn ‘where’ on the curve the mill ‘was’ and then to drive it continuously toward the middle, maximum power drawn. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads by cutting the solids feed to a minimum if the power drop below a specified threshold. Once the power rises above the threshold the solids feed is increased again to an intermediate value from where it start the perturbations again to find the maximum. This makes the milling circuit easier to operate."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. The image processing was performed using the Smartfroth software on the top surface of the froth. The system gives measurements of bubble size distribution, average bubble size and froth velocity. The froth velocity was used to estimate the volume of bubbles overflowing the weir yielding to the fraction of air overflowing the cell. This measurement is the complement of the rate of bubble bursting on the top surface. Also samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. Then, the amount of solids and liquid per unit area in the bubble lamellae was estimated gravimetrically. Both measurements were used to establish stability criteria.It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase to high frother dosage did not result in an improved fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance."

Jan 1, 2003