Search Documents

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis shows that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. Co-existence of ilmenite with pseudorutile, rutile and haematite is observed in substantially varying amounts in the three deposits. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among ilmenites in different places.In processing of ilmenite through the Becher process, aeration rusting of pre-reduced ilmenite is found to be the rate limiting step thus, affecting the productivity of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half.A new route of processing ilmenite for synthetic rutile has also been developed in which, ilmenite is carbothermally reduced and then processed through plasma route. The slag thus obtained is processed further to get high-grade synthetic rutile, metallic iron and high purity iron oxide. The process has been scaled up in a continuous moving bed plasma reactor. It is technologically and economically more viable where, all the iron values are recovered as salable byproducts. This paper describes the salient features of the technologies developed for the beneficiation of ilmenite to synthetic rutile."

Jan 1, 2003

By Harshad Bhagwat

The objective of this work is to investigate the inadequacies of current CFD based methodologies of model development for predicting combustion behavior of pulverized coal in furnaces. In the present paper, a steady state CFD model was used for in-depth analysis of pulverized coal combustion. The model accounts for turbulence, coal combustion, convective and radiative heat transfer and motion of coal particles. It also uses coal combustion models to account for important processes such as devolatilization, combustion of char and the evolution of fuel nitrogen during coal combustion. The model predicts fluid flow, heat transfer, progress of combustion and pollutant formation (NOx, etc.). The model uses several parameters, which need to be tuned with experimental data, which is not only limited in quantity but also insufficient in detail. Various existing methodologies like part calibration method for tuning of the parameters are discussed. In the present work, the parameters associated with coal combustion models were tuned and validated with published data obtained from an experimental furnace using one such part calibration methodology. The results clearly show that the model predictions differed with the experimental data not only quantitatively but also qualitatively. These discrepancies were attributed to part calibration methodology. A detailed parametric study was carried out to demonstrate the importance of parameters from various classes, namely, combustion kinetics, heat transfer, process and geometry parameters, and CFD model parameters. This investigation clearly indicates that parameters from different classes have significant effect on combustion behavior. The discrepancies in current methodology are discussed and a need for comprehensive methodology is highlighted. Keywords: pulverized coal combustion, computational fluid dynamics (CFD), pollutant formation (NOx), mathematical modeling

Sep 1, 2012

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012

By Ingvar Ymén, Alexandra Lundmark

"The depressive effect of dichromate on galena was evaluated with chemical experiments and small-scale depression experiments at a pH of around 12. The depressive effect was measured with Dynamic Vapor Sorption (DVS), which measures the water uptake of a sample as a function of the % relative humidity. The depression is due to PbCrO4PbO, which in the presence of Ca2+ and SO4 2- forms a more or less amorphous solid solution (Pb,Ca)(CrO4,SO4)PbO, which clogs to the surfaces of the ore. Free Pb2+- ions are needed for depression to occur and at high pH Pb2+ - hydroxide complexes, supply enough Pb2+ - ions to precipitate (Pb,Ca)(CrO4,SO4)PbO. In air CO2, precipitates CaCO3 which slowly lowers pH, precipitating more (Pb,Ca)(CrO4,SO4)PbO and CaCO3 on galena. Similar experiments where performed with five alternative depressors whereof phosphate, which forms an amorphous precipitate of approximate composition Pb3Ca13(PO4)10SO4, gave the best results. Phosphate was tested in laboratory scale flotation experiments giving encouraging results.INTRODUCTIONWithin Boliden Mines, concentrating of copper and lead from complex sulfide ores is performed by bulk flotation, meaning that copper and lead are concentrated in the same product. Downstream, copper and lead are separated by flotation of chalcopyrite, and depression of galena. Boliden has for many decades used sodium dichromate to depress galena (reference 1). Dichromate is both toxic and carcinogenic and Boliden has for many years investigated several alternatives. So far, however, the best results have been obtained with dichromate. Since Boliden has tried to substitute dichromate for a long time without finding a process as effective, Boliden decided to clarify the function of dichromate in the depression of galena and on the basis of the outcome find alternative depressors with similar function. This study was given to RISE Bioscience and Materials / Surface, Process and Formulation as a consultancy assignment. This paper presents the outcome of the combined efforts of Boliden and RISE."

Jan 1, 2018

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014

By O. Martinsson

The Kiruna area is an important mining province in northern Sweden, which is dominated by Fe- and Cu-Au deposits. Economically most important for the region, are the apatite iron ores with an annual production of c. 43 M ton of crude Fe-ore and a total production of more than 2000 M ton of ore the last 100 years. The apatite iron ores in the Kiruna area are dominated by either Magnetite or Haematite and contain varying amounts of apatite giving them a content of Fe and P, which varies between 30-70 % and 0.05-5 %, respectively. A typical geochemical feature of the ores is the strong enrichment of REE that is caused by a high content of REE in apatite and the occurrence of Allanite and Monazite containing 22.4 and 69.8 wt% REO, respectively. At Kiirunavaara, the content of REE in apatite varies between 0.07 to 1.57 wt% REO with a dominance for the light rare earths. The variation in REE-content of apatite depending on textural and paragenetic aspects is not known but apatite grains may display a strong LREE-depletion due to hydrothermal alteration. Monazite occurs as rod-shaped or tabular inclusions in apatite and is suggested, to have formed in response to hydrothermal alteration of apatite after the emplacement of the ore. Inclusions are mainly found in the central part of apatite grains occurring in veins and schliren, while they are rare in apatite occurring disseminated in the ore. Monazite also occurs as larger grains outside apatite and together with Allanite is found in texturally and paragenetically different settings within the ore. These occurrences of REE-minerals may largely be a product of LREE mobilized by alteration of apatite after the emplacement of the ore. However, REE-minerals including Allanite and Monazite might also have formed directly from late magmatic fluids. Keywords: apatite, monazite, allanite, ree, kiirunavaara, iron ore of kiruna type, mineral chemistry

Sep 1, 2012

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By U. M. J. Boin, W. L. Dalmijn, T. P. R. de Jong

"This paper explores the complex interrelationship between the resource cycle, recycling and metal production as a function of economics, environmental legislation, and product design. It is argued that central to optimising this resource cycle lies the control in particular of physical separation plants by the application of advanced sensor technology and sorting equipment, as well as suitable control and sampling algorithms supported by optimising mass balance models.Metals are produced through a long chain of processes. For primary resources, metals production goes through mining, mineral processing, ore smelting, conversion and refining steps or via low temperature hydrometallurgical processes, or a combination of both pyro- and hydrometallurgical operations. For the recycling of resources, metals are separated and recovered from metal scrap, which plays an increasingly important role in the world. Metals after being produced, either from primary or recycling resources, have to be further refined or manufactured into various types of alloys and finally shaped into different products for the end-users. Since the end-user discards products the contained materials find their way back into the resource cycle as scrap. Therefore, controlling the metallurgical reactors also controls, in a much broader sense, the material quality in the complete metals cycle, from the production phase, to the end-use phase, up to the recycling phase (Reuter et al., 2003). The recycling phase includes separation of materials into saleable intermediate products, which are reintroduced into the production phase as a recycling resource. Therefore, the metallurgical processes in each unit operation in the metals production and processing chain have to be controlled, so as to achieve optimal performance of high product quality, low energy and materials consumption, and low environmental impact."

Jan 1, 2003

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

In looking to the future of mineral processing the focus is typically on improved processing units. Basically it is a search for an elusive wonder machine that could revolutionise the economy of mining: the sorter that strips 50% of the ore with only a few % loss of value; the comminution device that uses 5% of the energy while producing fully liberated particles; or the recovery device capable of producing a 99% recovery at 99% grade. These aspirations are propounded against a reality backdrop of sorters rusting in back yards, mill throughputs below design and varying by 30%, cyclones flaring and cut-sizes fluctuating, mediocre recoveries and soaring processing costs. This disconnect between aspiration and reality appears, to these authors at least, to be a mighty chasm. Moreover, it remains one over which we are expected to magically leap rather than methodically bridge. Indeed one may be forgiven for thinking that should such a wonder machine come along, taking advantage of it would be highly improbable. Questions would inevitably emerge on how to feed the correct material, how to cope with the wide variability of feeds, how to control such advanced equipment and how to handle the new product from such a machine. It is likely these questions might lie unanswered, or more regrettably, unasked. It is generally accepted that as an industry we are exceedingly unlikely to teleport from the current status quo to an entirely new reality in a single flash. It is our thesis that the probability of these magical machines materialising is remote, and even if they miraculously appeared, we simply wouldn?t know what to do with them. Rather, it is our contention, that a step change will only arise through a staircase rather than from a single giant leap. We should focus on building those steps and linking them together into a firm structure ? a workable mineral processing circuit. This paper addresses the alternative of a coherent set of modest but significant improvements, integrated to produce the step change we desire: essentially, a reduction of processing energy to below 40%, which we believe is achievable without recourse to any mystical machines. A key underlying capability to designing these dramatically improved processes, is the weaving of independent process models into a coherent circuit simulation, in order to design the new generation of mineral processing circuits. Keywords: step change, circuit design, circuit simulation, energy reduction

Sep 1, 2012

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By Chiharu Tokoro

Acid Mine Drainage (AMD), high acid water containing heavy metals discharged from mines, has been recognized as major cause of mine pollution. In Japan, the government spends billions of yen every year to prevent pollution caused by AMD in about 80 abandoned mines. It is widely recognized that the treatment could continue for long decades or an even century. However, costs and environmental loads are uncertain during the treatment because a predictive model for the quality of AMD, the dosage of neutralizer, and the amount of sludge that is applicable for abandoned mines with limited data has not yet been established. In this study, a two-steps predictive model for solution composition and neutralization chemical requirements of AMD in future was constructed based on the geochemical modeling. Requisite input data of the model was the past historical water quality data from AMD monitoring, such as metal concentration and pH in the solution, instead of the sample rocks as other conventional prediction methods. In the first step, solution composition of AMD in the future was extrapolated from the available historical data using geochemical simulation considering the first order kinetics for the mineral dissolution. In the second step, neutralizer dosage and sludge generation in the future was predicted based on the geochemical simulation supposing the chemical equilibrium and oxidation state for all of elements in the solution. Based on case studies of two abandoned mines in Japan, solution composition, neutralizer dosage and sludge generation were estimated. The results of this study demonstrate the effectiveness of our model for the prediction of AMD quality and chemical requirements of neutralization treatment after mine closing. The model is useful for the estimation of the neutralizer dosage and the sludge volume in abandoned mines with limited data. Keywords: acid mine drainage, predictive model, geochemical modeling, first order kinetics, water monitoring

Sep 1, 2012

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By X. Cui

Hydrocyclone is widely used in closed-circuit grinding process. However, in the first classification operation of coarse particles with high pulp density, the shortcomings of traditional cyclone are that the grinding cycle load is much high, the apex of cyclone is easily to be blocked and classification efficiency is less. Specifically, the problems of traditional cyclone used in grinding process are as follows: (1) Mill utilization factor is low and its handling capacity is small. (2) Coarse particles mixing in cyclone overflow affects the following separation process and fine particles mixing in underflow causes over-grinding, which affects the total recovery rate of valuable minerals. (3) High grinding cycle load leads to large amount of high-density slurry pumping, which causes high energy consumption and severe wear of cyclones, pipelines and pumps. The applications of new type pre-classification hydrocyclone with centrifugal volute in the first classification process of Iron Mine Mill are introduced in the paper. Pulp particles fed in the centrifugal volute were arranged in advance, so that coarse particles can be far away from the overflow pipe, which can reduce the short circuit current to avoid coarse particles entering overflow and improve classification efficiency and accuracy of cyclone. The strong points of the new cyclone in the coarse classification operation are as follows: (1) finer overflow and less fine particles mixing in underflow improves classification efficiency more than 10%; (2) lower ball mill load cycle improves ball capacity more than 10%;(3) grinding energy consumption reduces by more than 20% and cyclone feed pump reduces energy consumption by more than 12%. In short, new type pre-classification cyclone with centrifugal volute solves the problems of fine particles mixing in underflow, high grinding cycle load and less classification efficiency in the coarse classification operation. Therefore, it has broad application prospects in ferrous metal and non-ferrous metal ore dressing plant.

Sep 1, 2012