Search Documents

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By Hossein Zarei, Masoud Kashani, Mehdi Safari

The feed of flotation unit in Angouran mine, as a part of Iranian Lead and Zinc National Corporation, contains about 34.26% zinc (about 12% Zn sulphide) and 10.14% lead (about 2% Pb sulphide). The grade of Pb and Zn in the final concentrate (rougher+scavenger), under optimal conditions (200 g/ton PEX, 500 g/ton zinc sulfate, 30 g/ton MIBC and pH = 7.5), was 63.18% and 13.01%, respectively, and the total Pb (sulphide-oxide) recovery was about 19% which included 95% Pb sulphide. The grade of Pb and Zn in rougher concentrate step was about 71.86% and 5.97%, respectively, when PEX (Potassium Ethyl Xanthate) was used as collector. While in the presence of PAX (Potassium Amyl Xanthate), the grade of Pb and Zn in rougher concentrate step was 66.8% and 10%, respectively. Tailing of the galena flotation (with 8.48% Pb grade and 34.92% Zn grade under the optimal conditions) was used as a feed for sphalerite and oxide section flotation.

Jan 1, 2014

By I. Yelkin, Erico Tabosa, Alex Jankovic, R. Hayashida, R. Faveere

"The mining industry faces growing challenges from more complex and lower grade deposits, rising costs, limited energy and water availability, and increasing societal pressure to operate more sustainably. Mining operations need to be more efficient, not just to reduce environmental impact, but also to remain economically viable.To maximize profitability and sustainability, existing operations and new projects must consider integration and optimization of all stages of production. A mining operation is essentially a series of inter-connected processes, with the performance and outputs of each stage affecting the subsequent ones. Optimizing stages in isolation can result in sub-optimal overall performance.The industry has long recognized the benefits of holistic optimization using the Mine-to-Mill concept, and there are many well documented successes. However, it is increasingly common to observe operations simply increasing explosive consumption in the mine and expecting optimization of the entire value chain (mining and processing). For true holistic optimization, blast intensity is not necessarily increased, but rather adjusted to best suit the requirements of the different types of ores treated, the circuit configuration and equipment, installed comminution power and the downstream beneficiation processes. It is a fully integrated effort with optimization of many aspects in the mine, comminution and separation processes.To be successful, optimization of the production chain from mine to process requires a site-specific, structured methodology supported by extensive ore characterization, auditing, surveys, data analysis, mathematical modelling simulations and a cost / benefit analysis. Following this methodology, optimization strategies are rapidly identified and implemented considering mine and plant constraints. Management needs to set up appropriate KPIs and site personnel need to be trained for the new operating strategies to be successfully incorporated into site practices and procedures in the production environment. This will ensure the benefits are achieved and maintained. This paper describes the methodology employed by Hatch to improve overall efficiency and profitability from mine to process. Two case study examples at Russian gold operations and benefits achieved are presented."

Jan 1, 2018

By H. R. Manouchehri

Sustainable development requires the optimal use of natural resources and recycling of the wastes. In fact recycling is the final productive use of obsoletes. ELVs, obsolete appliances and industrial wastes have become important resources for production of iron and steels, non-ferrous metals, and composites. Within shredding plants, these obsoletes are firstly shredded to the pieces and then processed to recycle different materials, especially ferrous and non-ferrous metals for metallurgy. Traditional and new developed mineral processing technologies are nowadays used for recycling different materials from waste effluents. Shredding and separating plants are currently recycle the wastes by make use of different technologies to mainly produce raw material for metallurgical application. However, other non-ferrous components are also treated for energy conservation and protecting environment. Currently, recovery in shredding and recycling plants maximises to 75% and about 25% of the feed is land-filled. However, recycling rate must be increased in due to the economical, environ-mental and social concerns. A comprehensive study for recycling, with especial focus on ferrous metal recovery, was sup-ported by Swedish Environmental Agency (MISTRA) to look at possibilities to increase the recycling rate and to reduce the amount of disposal. Part of this study was dedicated to study the shred-ding plant facilities and to look for possibilities to improve the quality and quantity of the shredding product streams. The aims were to improve the quality of ferrous scrap (apparent density > 0.9 and Cu<0.25%) for iron and steel production as well as having better quality for non-ferrous metals through the recycling schema, and finally to treat the shredder residue (SR) to recover metals and plastics to reduce the disposals. This paper summarises the results of sampling and conducting separation tests for improving the recovery of the ferrous and non-ferrous metals. The results indicated to be possible to obtain high quality ferrous scrap at recovery of 88%. However, the total recovery for metal scrap has reached 93%. Furthermore, test results on fine, P< 8mm, shredding residue (SR) showed promising prospect in recovery of metals and protecting environment by physical separation, i.e. electrical separation technique.

Jan 1, 2014

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

By S. C. Borah

Graphite, a mineral form of pure carbon, is one of the most versatile minerals in industry, because of its varying physical properties and characteristics. The mineral occurs naturally in the form of tubular crystals or microcrystalline earthy lumps, or it is disseminated in rocks, which have undergone intense metamorphism. India has a large deposition of graphite minerals out of which about 43% are found in Arunachal Pradesh. However, compared to the rest of the country, the North-East Region and particularly Arunachal Pradesh has not attracted attention till date for detail investigation for characterization, beneficiation, prospecting and/or exploitation of the mineral resources including graphite. Bulk graphite sample were collected from upper Subanshiri district of Arunachal Pradesh. Chemical analysis of the representative samples were carried out and found that 7.29%, 19.60% and 6.07% of fixed carbon (FC) is present in graphite sample collected from La-Lamdak, Bopi and Taliha, Arunachal Pradesh, respectively. Chemical analysis of the ash of the graphite sample shows presence of impurities such as silica, Al2O3, Fe2O3, Ca, Mg etc in the graphite sample which are also supported by XRD and SEM-EDX investigation. The graphite samples of Arunachal Pradesh are low grade and do not fulfill the market requirement for the industrial applications. Therefore, low-grade graphite is subjected to beneficiation for the upgradation of the graphite for industrial applications. We have adopted the dispersion?cum-settling technique for the beneficiation of the graphite sample collected from Arunachal Pradesh. The FC of 40.21% with 41.17% raw graphite recovery which is equivalent to 71.02% carbon recovery have been obtained by gravity separation technique using only distilled water without any chemical reagent in case of graphite sample collected from Bopi, Arunachal Pradesh. The graphite sample is upgraded up to 47.75% FC with 41.91% raw graphite recovery, which is equivalent to 85.85% carbon recovery with the pH adjustment at 9 with NaOH. Keywords: graphite, beneficiation, gravity separation, arunachal Pradesh

Sep 1, 2012

By Diana Drinkwater, Tim Napier-Munn

"This paper argues that, although specialist mineral engineering expertise is essential for the efficient design and operation of mineral processing plants, the environment in which these skills are supplied to the industry has changed forever, and not for the better. Most of the mineral engineering programmes in western universities have died or are dying. The long-service mine site mentors have gone, operations are run on a staffing shoestring so that there is no longer the time (or inclination) for considered decision-making, and the FIFO model has discouraged continuity of optimisation projects and communication between professionals. At the same time the technical challenges of designing and operating effective process plants are increasing. These trends are not going to be reversed any time soon, if ever. The ability to run efficient mineral processing operations has been materially compromised as a consequence. We propose that well-designed professional development can help to recover this situation, and it can be done easily and cheaply. The workplace is the best environment for such skills development. Professional development training should be integrated with normal duties throughout the early years of a graduate’s service (and probably beyond), and the cost should be regarded as non-discretionary expenditure for the business. If such programmes are properly resourced and managed and extended over longer time periods, there will be a measureable rise in the level of technical understanding and competence within companies and a resulting beneficial impact on resource utilisation and thus shareholder value. The paper outlines some of the approaches that we believe will work, and the benefits that we expect will accrue."

Jan 1, 2014

By M. Barsky, A. Govorov, E. Barsky

A study was conducted to determine the structure and lifting capacity of a two-phase stream in a vertical pipe at different distances from the point of introduction of the material into the instrument. Stream velocity was set at 2.8, 4.0, 4.8, 5.6 and 6.25 m/sec to ensure separation regimes. It was found that the llifting capacity of the two-phase stream exceeded that of pure air by a factor of three or more, and that in a turbulent regime the velocity curve displayed marked deformation, becoming more rounded and tending towards a parabola. The following formula was obtained for entrainment of a given size fraction under turbulent, laminar and transitional particle flow regimes:

Jan 1, 2003

By Mikhail I. Khersonskaya, Mark I. Mantsevich, Andrey V. Tarasov

"Due to depletion of the existing ore deposits the content of non-ferrous metals in produced ores has an inevitable tendency to decrease. Processing of low-grade ores is associated with production of low-grade selective concentrates and poses serious problems for the non-ferrous industry relating to increasing losses and expenses for waste treatment and disposal.The main component contaminating selective concentrates is iron sulphides.Copper-nickel, copper-zinc and polymetallic ores have been discussed as most important types of ores requiring removal of iron sulphides.One of the promising directions for development of selective flotation technology is the use of lowmolecular organic depressors. An advantage of organic compounds is in the possibility of multi-variant structure of organic molecules, which permits selection of a most efficient reagent for the given conditions. Another way for improving the grades of concentrates is concentration of valuable constituents associated with iron sulphides in an intermediate product and upgrading of the latter by chemical and metallurgical techniques.In order to remove iron from nickel concentrates, specific process conditions have been developed for selective flotation of pentlandite with the use of an organic depressor for pyrrhotite. The use of a depressor for flotation of high-grade copper-nickel ores ensures an increase in the nickel content up to 14% in the nickel concentrate produced as compared with 7% when using conventional process conditions, along with a nickel recovery improved by 2-3%."

Jan 1, 2003

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

By G. Belardi, N. Shehu, L. Passeri

"This paper illustrates the possibilities of applying what is essentially a physical soil-washing technique for treatment of soil contaminated by semi-volatile hydrocarbons in order to reduce the level of pollution to that permitted by Italian regulations.The ground around a factory producing lubricating-oil additives consists of silty-sandy soils which have long been contaminated by heavy hydrocarbons, especially branched alkyl benzenes and naphthalene derivatives. Pollution is particularly marked in some zones (hot-spots) where Total Petroleum Hydrocarbon (TPH) values are as high as 7000 ppm. The hydrogeological characterization showed the presence of a gravely soil in a sandy/silty matrix, with big stones making preferential paths to the water circulation. The permeability is 10-5 m/s and the water-table occurs at about 3 m below ground level.After laboratory and pilot-scale studies on representative samples of in-situ soils with TPH between 2700 and 7000 ppm a flow-sheet is proposed for reducing TPH values below the acceptable limits in Italy, namely 700 ppm for hydrocarbons with more than 12 carbon atoms and less than 250 ppm for those with fewer.On the basis of indications provided by laboratory tests a mainly physical treatment process of soil washing has been developed. This is used to clean-up soil from a site polluted by non-volatile hydrocarbons with a high TPH value. The process involves a high-density attrition stage followed by wet screening at 0.5 mm and then wet-gravity separation of the minus 0.5 mm fraction in the centrifugal field.The gravity separation products consist of a light fraction with particle size finer than 15 micron which contains most of the pollutants, and a heavy coarse fraction with TPH values conforming to the limits set by Italian regulations (less than 700 ppm hydrocarbons whose structure contains more than 12 C atoms, and less than 250 ppm of hydrocarbons with less than 12 C atoms)."

Jan 1, 2003

By A. C. Maffei, M. V. Lins Gonçalves

Ore concentration processes are a function of the respective particle size distribution; however, most of them do not use an efficient operational method to determine it. From a practical point of view, the surface area can be calculated for any size analysis. The physical principles for determining the size distribution in each method are different, for the results will not be compared directly. During the development of the research project of the sulfide ore flotation method using inert gas, different methods for calculating the specific surface area have been used, such as sieving, sedimentation/X-ray, laser diffraction and BET, i.e. specific techniques to determine the specific surface area of copper and gold ore concentrates. The statistical method of minimum squares was used to achieve practical correlation equations among them. Regarding these two ores, if one knows a specific surface area value using one of the methods above, one can predict the result of the others. Diminution of the reagent consumption was so controlled and it could be even decreased by using inert gas.

Jan 1, 2003

By M. Barsky, E. Barsky

A study was conducted to elucidate the relationship between the hovering velocity and the particle settling velocity. The experiments were carried out in a water medium on five materials ranging in density from 1.070 to 4.000 kg/m3. Analysis of the results with allowance for the distribution of stream velocities over the cross section of the pipe revealed that the final settling velocity of the particles was equal to their local hovering velocity (on the stream axis), and not to the average velocity of vertical flow as is generally believed. It therefore follows that the kinetic structure of the stream must be taken into account when constructing theoretical models of the process for purposes of computation. In addition, the optimal stream velocity is not always equal to the hovering velocity and in fact is governed by other factors as well. Illustration is provided by the results of a study conducted in a vertical cascade classifier comprising eleven identical stages. The feed material was introduced at each stage successively beginning with the topmost (i* = 1 ) and ending with the lowermost (i* = 11). First, the stream velocity that yields optimum separation conditions at each stage of the cascade (i.e. k=50%, k being the yield of a given size class in the fines for a single stage) was sought. Subsequently the conditions of optimal separation for the instrument as a whole were determined (i.e. F(x) = 50%, F(x) being the yield of a given size class for the entire instrument). The results of the study are presented in the table.

Jan 1, 2003

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

"Different hydrometallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2 (Vegliò and Toro, 1994). An innovative acid reductive leaching carried out in soft experimental conditions was here considered using agro-industrial wastes containing carbohydrates as reducing agents (Vegliò et al., 1998).The leaching process was investigated from a kinetic and equilibrium point of view in order to optimize the experimental conditions and obtain high purity and concentrated MnSO4 solutions.The overall leaching process (not considering the complex network of intermediate oxidation reactions of the carbohydrates in hot sulphuric acid medium (Vegliò and Toro, 1994)) can be described by the following reaction:24 MnO2 + C12H22O11 + 48 H 24 Mn2+ + 12 CO2 + 35 H2O (1)A Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis and BET surface measurements before and after leaching.Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydroalcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions."

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By K. A. Natarajan

Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.

Jan 1, 2003

By Tuan V. Nguyen, Louis Mittoni, Murray Rudman, CSIRO Minerals, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D “Improving Thickener Technology” project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Rob D. Morrision, Paul W. Cleary

"The best accepted method for design of autogenous and semi-autogenous mills is to carry out pilot scale test work using a 1.8 m diameter by 0.6 m long pilot scale test mill. The load in such a mill typically contains 250,000-450,000 particles larger than 6 mm, allowing correct representation of more than 90% of the charge. This scale of DEM model is now within the practical range of standard workstations running an efficient DEM code.This paper describes various ways of extracting collision data from the DEM model and translating it into breakage and wear estimates. Account is taken of the different breakage mechanisms (impact and abrasion) and of the specific impact histories of the particles in order to assess the breakage rates for various size fractions in the mills. These impact histories have the potential to be directly related to breakage as they most resemble the single particle breakage tests which are used by the JKMRC to calibrate more traditional population balance models for variations in ore behaviour. However, the specific impact histories also show a background of many low energy collision events within the mill. This Background may constitute what is usually regarded as “abrasion” breakage. As might be expected, high impact events are concentrated in the toe of the charge and near to the mill shell where the forces associated with the load bearing on each particle is more concentrated."

Jan 1, 2003