Search Documents

By Alireza Ayoubian, Douglas S. Roy, Gianni O. Chieruzzi

"A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt.More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter.Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.IntroductionA 400 MW, gas-fed power plant was constructed near Moscow in the Province of Moskovskaya in Russia.Figure 1 shows the general arrangement of the main structures, and the geometry of the piles supporting those structures."

Jan 1, 2017

By Scott M. Mackiewicz

This project includes replacement of the historic vertical-lift span Meridian Bridge (U.S. Highway 81 over the Missouri River) that connects Yankton, South Dakota with rural Cedar County, Nebraska. The new 76-foot wide, 1,590-foot long steel plate girder structure required the use of drilled shaft foundations that extended into the underlying Carlile Shale formation. Designers indicated that an individual drilled shaft capacity of about 2,000 kips will be needed at each of the river piers, and based on the subsurface information, 8 to 10-foot diameter drilled shafts extending to about 115-foot would be required for support of the bridge structure. An Osterberg Load Test was performed on one test shaft to determine the ultimate skin friction and end bearing of the Carlile Shale. This paper describes the design and installation of the load test drilled shaft as well as presents the load test results as compared with predicted design values determined using FHWA methods.

Jan 1, 2008

By Goudschaal Mark R.

"The Museum of Science and Industry U-505 Submarine Relocation project in Chicago, IL consisted of building an underground reinforced concrete vault (37' deep) for the Museum's new U-505 exhibit. This WWII submarine was captured in 1944, had been located outdoors at the Museum since 1954 and was lowered into its new exhibit area in 2004. A unique combination of earth retention, water cut-off and underpinning systems allowed a forty-two foot (42') deep excavation underneath th is historic museum. The museum - originally built in 1893 for the Chicago World's Fair - was closely monitored for building movements throughout construction. The underpinning systems, construction activities and monitoring results are presented herein. IntroductionThe historic U-505 German submarine at the Museum of Science & Industry was restored, moved approximately 1,000' and then lowered into its new indoor home (Figures 1, 2 and 3). The new underground exhibit opened this year celebrating the 61st anniversary of the German submarine's capture on June 4, 1944. On this historic day, Captain Daniel V. Gallery, a Chicago native, led the Navy in the siege of this submarine near the coast of Africa. This U-boat was the only German sub captured by the United States Navy in WWII and the Enigma machines, codebooks and publications recovered from the sub helped the war effort."

Jan 1, 2005

By Lisheng Shao

Soil mixing and jet grouting have been widely used to support heavy structures such as tanks, cement silos, and storage buildings. Although the installation methods vary between soil mixing and jet grouting, the end product of soil-cement columns behaves similarly in supporting structure loads. In many cases, soil-cement mass treatment offers the owner savings over driven/drilled piles. This paper discusses the design methodology, production work, and quality control, with supporting figures, of a recent large complex tank farm project. The project consisted of constructing six above-ground steel storage tanks and an approximately 700-foot-long fill slope. The tank farm site is located in an industrial area of southern California, with highly variable subsurface conditions consisting of compressible soils and buried construction debris. The compressible soils necessitated that the new tanks be supported on deep foundations. A test pile program performed previously at the site showed that conventional driven concrete piles were not feasible because of buried construction debris, therefore a soilcrete system was proposed. Site design included evaluating the total and differential settlement and column group bearing capacity under both static and seismic loads. Extensive field and laboratory testing confirmed the design soil-cement strength and modulus of both the soil mixed and jet grouted soil-cement columns. The project operation and quality control programs are also included in this paper.

Jan 1, 2010

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Franz-Werner Gerressen

In the changing construction environment clients are searching for new technology to complete their projects in shorter times. Manufacturers are therefore developing solutions to speed up established construction methods. The significant progress in recent years with the development of increasingly powerful drilling rigs is providing piling companies increase options for the execution of specialist foundation projects. The double rotary drilling methods are primarily used for the construction of pile walls as support for deep excavations. Typically these retaining walls are designed and installed as cased piles using the established Kelly drilling mode. However, more recently it is more popular to undertake these projects with the Cased Continuous Flight Auger (CCFA) system. This paper provides an overview of drilling with double rotary methods, in particular the monitoring during installation.

Jan 1, 2009

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By Michael J. Marasa

"Geotechnical engineering and construction primarily relies on the subsurface characteristics of the particular site; however, obtaining both accurate and precise information on those features is challenging due to the numerous factors involved in testing procedures used to analyze varying site geology. This includes a detailed and thorough geotechnical investigation to understand the site conditions, allowing the implementation of the most practical and economical solution.This paper presents a case history of the installation of wick drains and construction of aggregate piers on the site of a large facility to be constructed in Memphis, Tennessee. Throughout intensive subsurface investigations, highly variable soils were encountered, requiring settlement control and increased bearing capacity. This paper will discuss the design and installation of the systems constructed, and procedures and execution of the work to ensure design specifications were achieved.BackgroundA 1.4 million square foot expansion directly adjacent to an existing 1.1 million square foot distribution facility in Memphis, Tennessee was planned to serve as a centralized facility for increased production. The first phase of construction included an 858,000 square foot warehouse and parking lot for approximately 400 trucks to the north of the existing structure. The anticipated column load for the warehouse was 125 kips; slab design bearing pressures ranged from 200 to 500 pounds per square foot (psf) and elevations ranged from EL. 264 to 282. Parking lot elevations ranged from EL. 264 to 290, requiring a design life of 10 years with an estimated 100 in- and out-bound trucks daily and maximum weight of 80 kips per truck. The second phase of construction took place east of the existing structure, and included a 794,000 square foot multi-level warehouse, a 100,000 square foot office, and additional employee parking. The anticipated column load for the second warehouse was 225 kips and slab design bearing pressures ranged from 200 to 500 psf. Elevations ranged from EL. 267 to 282. Anticipated column loads from the office were 25 125 kips, with slab design bearing pressures ranging from 100 to 200 psf. Due to the varying elevations within each planned footprint, up to 18 feet of new fill was required to match the existing structure’s finished floor elevation (FFE) at EL. 282."

Jan 1, 2017

By Fred Tarquinio, Giovanni Bonita, Lars Wagner

"A new embassy for the Peoples Republic of China is under construction in Washington, DC. The 475,000 square feet (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. A vertical soil nail wall was used as the primary support of excavation system for the project. The soil nail wall was irregularly shaped, benched in areas, and up to 98 feet (29.9 m) in height. The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Design and construction challenges included soft soil conditions, inside wall corners, underground utilities, seismic impacts from blasting, and logistical and political factors. Overall, wall movements were lower than expected, with maximum horizontal movement less than 0.25% of the total height of the excavation. INTRODUCTIONThe proposed Embassy of the Peoples Republic of China in Washington, DC, will consist of about 475,000 ft2 (44,125 m2) of building space and contain up to four fl oor levels above ground and fi ve levels of basement (Figure 1). When completed, the building will be the largest embassy in Washington, DC. The architect for the project, Pei Partnership Architects, along with the world-renowned architect I.M. Pei, made effi cient use of the site by inserting the building into the existing slope. Consequently, excavations reach heights up to 98 feet (29.9 m) on the southern side of the property and 42 feet (12.8 m) on the northern side.The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. The location of the building relative to the property line called for tight excavation requirements, including precise wall positions and shotcrete tolerances. Design and construction challenges included soft soil conditions, inside wall corners, arched walls, underground utilities, seismic impacts from blasting, and logistical and political factors."

Jan 1, 2007

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By Boo Hyun Nam, Berk Turkel, Luis G. Arboleda-Monsalve, Jorge E. Orozco-Herrera

Construction of buildings, roads, and traffic activities generate vibrations to urban infrastructure. The vibrations produced by construction activities have an impact on the soil through which they are transmitted. These effects become much more significant in granular soils. The soil conditions in Florida consist mainly of sandy soil deposits and this makes driven piles a commonly used method. In the design of deep foundation installations, it is significant to consider the potential construction issues related to the driving process. This process generates vibrations in the surrounding soils and thus, its effects on nearby soils and structures must be considered. This paper presents a web-based survey conducted among geotechnical engineers in Florida to better understand the common practice and experience regarding the effects of pile driving on surrounding soils and structures. The perception of different practitioners in the state of Florida on ground deformations and damages to adjacent structures induced by deep foundation installations are investigated. The engineers who have experienced ground vibrations and deformations were asked to define the susceptible soil conditions and main triggering factors of large ground deformations induced by pile driving. Sandy soils with loose to medium relative densities were found to be the most susceptible soil condition to generate ground deformations. Conclusions are drawn regarding the importance of considering ground vibration monitoring during the design phase of deep foundations.

Oct 1, 2022

By Yuji Yamashita, Kazuyoshi Kamimura, Tsuyoshi Takahashi, Naoya Matayoshi

"The CDM-LODIC method (cement deep mixing - low displacement and control) method enables ground displacement to be reduced by removing an amount of soil equivalent to that of injected cement slurry and the volume of the plunged mixing tool, which causes a certain degree of ground displacement. Since the CDM-LODIC method was developed in 1985, it has been applied to over 930 sites and the accumulated volume of stabilized soil has now reached 7.6 million cubic meters.In the CDM method, the number of blade rotations per unit depth in the ground when the mixing blades are withdrawn is considered a construction item. The blade rotation number depends on the degree of mixing between the cement slurry and the ground Some field tests were performed based on the degree of mixing between the cement slurry and the ground. In these tests, a new concept of evaluating the blade rotation number when the screw rod penetrates to a given depth without injecting cement slurry has contributed to the degree of mixing. Furthermore, a correlation exists between the coefficient of efficiency of soil removal and the cement slurry admixture rate. In this paper, we discus the data collected in those field tests and present some application examples.OUTLINE OF CDM-LODIC METHODThe injection of cement slurry may cause some ground displacement during Cement Deep Mixing (CDM). In recent years, due to an increased demand for ground improvement work in urban areas, there is increased concern that buildings near any CDM site may be adversely affected. The deep mixing method which reduces displacement due to mixing (CDM-LODIC method) enables ground displacement to be minimized by removing an amount of soil equivalent to the injected cement slurry and the volume of the mixing tool, which itself causes some ground displacement. When the construction site is near other structures, regardless of whether on or under the ground, the CDM-LODIC method can be used in order to minimize any ground displacement. There are considered to be two main causes of ground displacement as shown in Figure 1. Displacement A indicates ground displacement caused by the volume of the inserted mixing tool during the penetration stage and displacement B indicates ground displacement caused by the volume of the injected stabilizing agent. Thus, by removing soil equivalent to the volume of the inserted mixing tool and the injected stabilizing agent, ground displacement can theoretically be minimized. Figure 2 shows the amount of observed ground displacement in the cases of CDM and CDM-LODIC at an actual site. These case studies indicate that ground displacement can be reduced by removing the soil."

Jan 1, 2015

By Nabil F. Ismael

"Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.INTRODUCTIONShort, large diameter bored piles are used with increasing frequency for heavy structures in Kuwait, and the Gulf region where ground conditions indicate loose deposits of calcareous sands. The piles range in length from 8 m to 15 m with their base located in the dense-to-very dense, cemented sand bearing deposit. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on large diameter bored piles installed through loose calcareous sands into dense-to-very dense cemented or partially cemented sands are very limited at present. The results of three load tests carried out recently on bored piles at one site in Kuwait have become available. In these tests the failure load was either reached or can be extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers.This paper presents the soil conditions, pile installation details, and the pile load test data at the test site located in Shuwaikh, Kuwait. The site is facing the Arabian Gulf. Test results were directly analyzed and the point resistance, and skin friction were calculated. The ultimate capacities of the piles were calculated and compared with the measured values. The influence of the pile diameter on the settlement at ultimate and at working loads is examined"

Jan 1, 2017

By Naoyuki Hanawa, Takeo Asanuma, Tatsuo Nagatsu, Sachihiko Tokunaga, Daisuke Nakagawa, Yoshiyuki Morikawa, Kazuhiko Ueno

"In the cement deep mixing (CDM) method, one approach to joint construction is creating a surface-contact joint. In this study, an unconsolidated-undrained triaxial compression test was performed on cement-treated soil specimens with joints artificially created by successive pouring. The effects of the presence or absence of such successive pouring joints on the strength of the specimens were then examined. The results showed that the compressive strength of the specimen decreased by approximately 0%–30% with a successive pouring joint.INTRODUCTIONIn the block type and wall type improvement patterns of the CDM(Cement Deep Mixing Method) application, an integrated body of soil-cement columns is constructed by partially overlapping individual treated soil columns. The overlapping operation should be implemented before the hardening of soils by cement progresses and thus, this operation is routinely performed in construction sites usually within 24 hours or within 48 hours at a maximum. However, when the operation is forced to be interrupted on account of a typhoon or any other adverse weather conditions, it is impossible to carry out the overlapping operation within the above time limitations. In such a case, it is necessary to improve the integrity between the treated soil columns solidified first and the treated soil columns to be constructed later.One of the methods that can be adopted is to prior agitate the target area by mixing blades “without cement”, integrating the preceding treated soil columns and the subsequently treated soil columns at construction joints. This method has been adopted so far in numerous sites because no additional materials or equipment are necessary. However, its effectiveness has scarcely been evaluated quantitatively in conventional studies.In the circumstances, the authors investigated in the present research the effect of the presence or absence of construction joints on the specimen strength by performing unconsolidated-undrained triaxial compression tests using specimens of cement treated soil artificially provided with surface-abutting construction joints.Therefore, this study examined the effects of the presence or absence of artificially created successive pouring joints on the strength of cement-treated soil specimens through an unconsolidated-undrained triaxial compression test."

Jan 1, 2015

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) technique is widely known as soil mitigation technique with small ground displacement during installation comparing with other techniques. Some projects involving sensitive structures, however, require smaller impact than in conventional technique. In order to reduce ground displacement during DJM installation, this paper introduces systematic mixing technique, RD-DJM (Reducing Displacement – Dry Jet Mixing). RD-DJM is characterized by injection nozzle on the rim of mixing blade and fin plate on mixing shaft. These devices contribute efficient collection of injected air toward mixing shaft and result in reduction of ground displacement. The authors demonstrate successful performance of RD-DJM indicating difference between conventional installation and RD-DJM technique.INTRODUCTIONThe Dry Jet Mixing (DJM) method is one of the most common techniques in Japanese deep soil mixing field and characterized mechanical mixing of powdery binder with in-situ ground (dry-mixing technique). It is widely believed that DJM Method has great advantages in less quantity of binder to achieve the desired strength and less waste generation during installation.DJM method can meet the required strength with less binder content than wet mixing. And volume of binder of dry mixing is absolutely less than wet-mixing injecting considerable volume of binder slurry. This means that dry mixing causes less ground displacement compared with wet mixing.As the medium for forced feeding of the binder, the DJM method uses compressed air, which is blown from the mixing blade nozzles to scatter the binder and then recovered through the periphery of the mixing shaft to the ground surface. Because the binder is injected outward from the injection orifice at the root of the mixing shaft, a part of the air may escape to untreated areas due to the blockage of air recovery path around the mixing shaft. Figure 1 illustrates possible escaped air and leakage around installation location."

Jan 1, 2015

By Mamdouh Hamza

The construction of 1200 m length new quay wall located 1,300 m East of the existing Suez Canal bypass and about 1,000 m south of the Mediterranean shoreline is one of the main projects currently under development in Egypt. Due to very weak foundation soil, mainly soft clay, a particular effort, both in terms of design approach and construction feasibility, has been required. The execution of "barrettes" and T-shaped" diaphragm wall panels down to a depth of 65 m and under extremely severe soil condition has been required in order to pass through the upper soft soil and to reach a competent base layer. Very critical and variable hydrological conditions have been also encountered due to the contemporary nearby channel dredging activity, thus increasing the difficulty for maintaining the stability of the slurry trenches opened in soft material. This paper gives a general overview of the project with some emphasis to the most significant design aspects and to the construction of the deep foundation elements.

Jan 1, 2002

By Hamed Ardalan, Mohamed Ashour

"CHAPTER 1INTRODUCTIONThe use of piles to stabilize active landslides or to prevent instability in currently stable slopes has become one of the most important innovative slope reinforcement techniques over the last few decades. Piles have been used successfully in many situations in order to stabilize slopes or to improve slope stability, and numerous methods have been developed for the analysis of piled slopes (Ito et al., 1981; Poulos, 1995; Chen and Poulos, 1997; Zeng and Liang, 2002; Won et al., 2005).The piles used in slope stabilization are usually subjected to lateral force through horizontal movements of the surrounding soil; hence they are considered to be passive piles. The interaction behavior between the piles and the soil is a complicated phenomenon due to its 3-dimensional nature and can be influenced by many factors, such as the characteristics of deformation and the strength parameters of both the pile and the soil. The interaction among piles installed in a slope is complex and depends on the pile and soil strength and stiffness properties, the length of the pile that is embedded in unstable (sliding) and stable soil layers, and the center-to-center pile spacing (S) in a row. Furthermore, the earth pressures applied to the piles are highly dependent upon the relative movement of the soil and the piles."

Jan 1, 2013

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009