Search Documents

By F. Mallozzi

"With the requirements of air pollution codes becoming more and more critical, the role of the ventilation engineer in industry has become an extremely important one. The ventilation engineer must provide the expertise for the selection of equipment and the design of systems which will reduce pollution to an acceptable level. Because pollution control systems involve considerable capital and operating expense, he must have the ability to select, from a wide range of products, the collector which will provide the required performance with a minimum of down time for maintenance. This paper discusses the principles of wet collection and the forces used to separate particulate matter from a gas stream. Important factors in the selection of equipment, such as collection efficiency, horsepower requirements and water consumption for the various types of collectors, are discussed in detail, as well as the construction features normally incorporated to circumvent potential problems."

Jan 1, 1971

By L. Hacini, N. Van L ê, P. Bacher, D. Thibault

Manufacturer welded components may suffer from high level of residual stresses which can cause premature cracking and decrease the life of the components if they reach values close to the yield strength of the material. In the present work, a robotized hammer peening technique is simulated by an impact machine and the residual stresses generated by the indentation are measured. To better understand phenomena behind residual stresses relaxation by hammer peening, the impact energy level was changed. 304L steel plates were hammer peened with 10 impacts. The contact between the hammer and sample surface was always at the same location. The strains on the surface close to the impact location were recorded during the test using strain gauges to follow residual stresses variations. At the end of the test residual stresses were measured indepth using hole drilling technique at 8mm from the impact center. The micro-hardness was monitored to evaluate the affected zone by the hammer peening. This approach gave a good estimation of the energy and number of blows to be used for efficient relaxation of the manufactured parts.

Jan 1, 2006

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989

By J. P. Grieco, F. W. Grieco

"Manufacturing of Jaw CrushersOriginIn 1858 Eli Whitney Blake invented the first successful mechanical rock breaker-the Blake-type jaw crusher. Blake adapted a mechanical principal, the powerful toggle linkage system used to transform rotating motion and energy into oscillating mot ion and tremendous compressive forces. Today these same principals apply and the basic Blake-type jaw crusher is one of the leading machines of its class for heavy duty primary crushing service.In 1881 Philetus W. Gates patented a design for a crusher, the forerunner of the modern gyratory crusher which dominated the field from the late 1800s to the early 1900s. In 1910 the largest gyratory crushers built had 48-inch openings. However, about this time the jaw crusher came to life when the Power and Mining Machinery Co. built an even larger sized opening crusher-a giant 84-inch by 60-inch jaw crusher for a trap rock quarry in Pennsylvania. A 24-inch gyratory crusher became the ideal sized secondary machine for this size jaw. From that time on jaw crushers were looked on favourably as primary breakers and lines were brought up to date to parallel the already developed gyratory lines.FunctionMost heavy duty Blake-type jaw crushers work basically the same way. They are ruggedly designed and capable of crushing material in some cases in excess of 80, 000 p.s.i. compressive strength. They are very simple machines with few moving part s and, with the exception of replacement of renewable parts, are relatively maintenance free. It is quite common to have these machines in product ion for 20 to 30 years. The following will de scribe how these machines work. Large-diameter high-inertia flywheels which are connected to the main eccentric shaft, rotate inside a connecting rod type mechanism called a Pitman. It transforms rotating motion into vertical oscillating motion. This vertical motion is in turn transformed into reciprocating mot ion by means of a system of 2 toggles, each connected to the Pitman. The rear toggle is connected to the fixed rear head, and the front toggle is connected to the swing jaw which is hinged at the top of the crusher. With each rotation of the eccentric shaft the swing jaw opens and closes on rock which is fed into the crusher chamber, crushing the rock in a series of bites. These bites, or strokes as the y are called, usually vary between 1/2 inch to 1 1/2 inch at speeds of 120 to 200 strokes per minute. The reduction ratio of feed input to discharge is usually about 8 to I. Output capacities can vary from 100 tons/hour to 1200 tons/hour depending on the size of machine and its discharge opening. Horsepower requirements can vary from 75 hp to 400 hp.The entire crusher chamber is lined with replaceable 14070 manganese steel liner plates. This material is ideally suited for the job since it hardens as it wears during crusher operation. Manganese is also used in the high wear areas at each end of the toggle plates."

Jan 1, 1985

By G. H. Blackwell, A. J. Sinclair

"The main components of a ""PC” -based mineral inventory system are described in a sequence common to many real reserve/ resource estimation projects and in the practical context of problems and decision-making typically encountered in such studies. Some components are designed particuarly to improve the geostatistical instructional capability of the package. An important part of this approach involves the use of widely available software for data manipulation and evaluation in the design of a mineral inventory study progressing to mine design and feasibility. A variety of more or- less fixed routines written in high level languages provide acceptable computational speeds on a personal computer. These critical segments are linked by simple, short, compiled Basic programs easily adjustable to various data configurations and needs. IntroductionGeostatistical mineral inventory estimation has progressed greatly since its slow dissemination during the 1960s. The mining industry generally has accepted the benefits of the technique, notably the quantification of grade and geology, an indication of error in grade estimation, and of the mined volume / grade variance relationship (Clark, 1979, Isaacs and Srivastava, 1989).Acceptance has been slowed, first by complexities of geostatistical theory and second by a bewildering variety of computer systems and applications programs. Continuing improvements in education will facilitate a better understanding of the underlying theory.The purpose of this paper is to describe, in a practical context, the development of a geostatistical-based approach to reserve/resource estimation. The approach integrates various existing commercial software packages with a wide selection of programs developed by the authors for personal computers which estimate mineral inventories and educate users in the techniques applied; that is, the QMIN system.It is hoped that the approach presented here will convince mining and geological engineers concerned with resource estimation, of the soundness of geostatistical methods and its broad potential to their problems."

Jan 1, 1992

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By H. Utsunomiya, Mehdi Sanjari, Abu Kabir, Steve Yue, Jing Su, L. Kestens, In-ho Jung

The microstructure and texture evolution of low temperature rolled AZ31 magnesium alloy during annealing were investigated. The specimens were rolled at the temperature of 100? at a high rolling speed of 1000m/min with a reduction of 30% in one pass. Annealing was conducted at various temperatures ranging from 200? to 500? for different time. To study the effect of fast speed rolling, the same annealing procedures have been applied for the specimens rolled at a significantly lower speed of 15m/min. The microstructure was characterized by optical microscopy and scanning electron microscopy, while the texture was analyzed by X-ray diffraction analysis and electron backscattered diffraction analysis. Texture weakening occurred during annealing at both fast and slow rolling speeds. However, at the same annealing condition, fast rolled specimens always had weaker intensity of basal texture than slow rolled ones.

Jan 1, 2014

By R. B. Casault, J. D. Boyd, D. R. Bell

"Full-scale sections of three different types of Grade 483 line pipe have been evaluated extensively. The variations in chemical composition, optical microstructure, tensile properties, hardness and Charpy impact toughness with specimen orientation and location were determined. Significant variations in several properties, notably Charpy shelf energy, impact transition temperature, inclusion content and ferrite grain size, were observed for different locations in the pipes. The results indicate that current specifications call for test samples for the most conservative locations, except for impact tests. Minimum Charpy impact values generally occur at the II2-width location, which may be a more appropriate specified test location than the present I/4-width location. The anisotropy of impact toughness, and the importance of low sulphur content and inclusion shape control for adequate toughness in the transverse/rolling-direction orientation were demonstrated. The orientation of impact specimens is critical for spiral-weld pipe, and the current specification test is non-conservative in that it can give results which are two to three times higher than the minimum value for the steel.IntroductionThis report presents the results of an extensive metallurgical evaluation of three different Grade 483 line-pipe steels. The sample material came from full-scale sections of line pipe, which represented current commercial practice at the time of manufacture (1975-1977). Since then, significant improvements have been made in the manufacturers' procedures for producing skelp and pipe, and the line-pipe specifications have been revised. Hence, the information in this report is dated in terms of current design, but it is unique and significant in several respects:"

Jan 1, 1982

By M. J. Medd, G. A. Speirs

"This paper describes the simultaneous sinking and equipping of a 4.9 m diameter concrete-lined shaft to a projected depth of 1660 m. The shaft blast design utilizes the full face method using a parallel hole burn cut. Hydraulic drilling and a totally redesigned Cryderman-type mucking unit were integrated into the four deck sinking stage to provide for drilling, mucking, concreting and shaft steel equipping operations. A safety program was tailored and implemented specifically for this shaft sinking project.IntroductionIn July 1988, Falconbridge Limited commenced development of its Thayer Lindsley exploration site located some four km north of Sudbury on Regional Road 80.The first phase of this project was awarded to J .S. Redpath Mining Consultants Limited and the scope of work included the engineering and project management to construct a surface plant capable of supporting a shaft sinking and exploration program for potential future mine development. This initial phase of the project was completed on schedule and under budget on December 23, 1988, and is the subject of an independent paper.In November 1988, J.S. Redpath Limited was awarded the shaft sinking and exploration phase of this project. The scope of work consisted of sinking and equipping a 4.9 m diameter shaft to a depth of 1660 m and carrying out the development and diamond drilling on two levels. This work was scheduled to be completed by November 1991.The T .L. Exploration Project is located toward the eastern end of the south range of the Sudbury basin, north of Sudbury. Figure 1 details the projected mining area and the shaft location on the geological complex. Figure 2 is a section showing the exploration shaft that is located in the Norite. Two levels will be developed from this shaft, on the 1310m and 1588 m levels, to provide access for further geological examination of the ore bodies."

Jan 1, 1991

By I. Stefanou, J. Sulem

"In the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface. Multiphysics couplings play a major role in earthquake nucleation and seismic slip. The effect of shear heating and thermal pressurization may be of prime importance in the control of the stability of shear deformation inside the slipping zone. Other mechanisms in relation with thermal decomposition of minerals affect the pore pressure and the temperature evolution of the system, and can play a significant role in the extreme strain localization observed in field. The actual width of the localized zone is a key parameter for understanding fault weakening mechanisms. On the basis of field observations, laboratory experiments and recent advanced modeling, these phenomena are analyzed and discussed in order to bring some new insights in the understanding of earthquakes nucleation.INTRODUCTIONIn the last thirty years, the study of earthquake mechanisms has emphasized the major role of rock friction. Earthquakes appear to be the result of a frictional instability and occur by sudden slippage along a pre-existing fault or a plate interface (Scholz, 1998; Sykes, 1978). The conceptual model of spring slider system is commonly used to represent the interaction between an elastic crustal block and a fault zone. Stick-slip instability is possible if the softening rate of the shear resistance of the fault zone is high enough as compared to the stiffness of the crustal block. Therefore, weakening mechanisms that can explain how the frictional resistance of a fault decreases with slip and/or slip rate is of prime importance to understand how an earthquake nucleates. In recent years, several drilling programs in active faults (e.g. the Nojima fault in Japan, Boullier, 2011; the Aigion Fault in Greece, Cornet et al. 2004, the Chelungpu fault in Taiwan, Ma et al. 2006, and the San Andreas fault in the U.S.A. Ellsworth et al. 2000) as well as high velocity friction experiments (e.g. Tanikawa et al 2012a; Tanikawa et al. 2012b) have highlighted the physico-chemical processes involved in the nucleation of seismic slip (see for the example the review paper of Niemeijer et al. 2012)."

Jan 1, 2015

By J. A. Finch, R. R. Cunningham

The amount of foam volume generated in relation to the gas flowrate has long been used to define the foaminess of a solution and to characterize surfactants. The vessel geometry and gas flowrate range can affect the foam volume results. A fixed area column was tested alongside a variable area conical vessel with two surfactants. It was found that the fixed area vessel will cause foam volume to expand or contract which masks the effect of the surfactant. The conical vessel showed two regimes of foam volume production dependant on gas flowrate. The low gas flowrate regime revealed the physiochemical nature of the surfactant while a high gas flowrate revealed kinematic properties. Foaming properties of a surfactant is best determined with a variable area vessel at low gas flowrate.

Jan 1, 2009

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By Amyn S. Dahya, David J. King

"The object of the paper is to discuss the developments in Carbon-In-Pulp (C.I.P.) technology for gold recovery. The CIP process is comprised of four major operations:(a) adsorption of precious metals onto activated carbon;(b) elution (stripping) of precious metals from the loaded carbon;(c) electrowinning of the precious metals from the concentrated eluate;(d) regeneration of the eluted carbon before recycle to the adsorption process.A detailed review of the technological developments in each of the above operations is presented together with a brief theoretical background of the underlying processes. The advantages and disadvantages of the CIP process are discussed in comparison with conventional zinc precipitation. IntroductionThe carbon-in-pulp (CIP) process involves the use of activated carbon for treatment of pulps containing dissolved precious metals, and provide s an alternative to the conventional gold recover y processes using filtration or counter-current decantation in conjunction with the Merrill-Crowe zinc precipitation process. The commercial application o f the CIP process in gold processing technology is a fairly recent development and it is of growing importance around the world.The fact that activated carbon ha s the property of adsorbing precious metals from solution was first published in 1847. In the following years , a great deal of work was carried out to develop an over-all recover y process using carbon, but all attempts were uneconomical because the loaded carbon had to be smelted to recover the gold.It was not until 1950 that Zadra, at the United States Bureau of Mines Research Centre in Reno, Nevada, developed a technique for stripping the loaded carbon using sodium sulphite-sodium hydroxide mixtures and then recovering the gold from the stripping solution by electrolysis. However, this process was not effective for stripping silver and further testwork was carried out on alternative stripping techniques. In 1952, Zadra published a paper describing the use of a hot sodium hydroxide- sodium cyanide stripping technique, which was effective in stripping both gold and silver. This paper included a description and flowsheet for the CIP process which is essentially the same as we know it today. This technique was used in the first major CIP plant, constructed and commissioned in 1973 by Hornestake Gold Mining Company. Since then there have been numerous CIP plants built in the U.S A., South Africa and Australia."

Jan 1, 1983

By D. Seo, P. Au, S. Yandt, N. Tsuno, A. Sato

Nickel-base single-crystal superalloys are used for gas turbine airfoil applications due to their excellent high temperature properties. A good understanding of the mechanical response of these alloys under different temperature and loading conditions is essential for modeling their behavior. In this study, the low cycle fatigue behavior of CMSX 2 oriented with the loading axis along [001] was investigated under zero-compression strain-controlled loading at 1100°C. The experiments were performed with or without a two-minute dwell (hold) in compression. The microstructure before and after testing was analyzed to understand the deformation characteristics including the effect of dwell.

Jan 1, 2010

By R. Neumann, O. Gomes, S. Gaydardzhiev

"Phosphorus in iron ores is considered as a deleterious component to iron making reflecting in cold shortness of the produced steel. The present study investigates the phosphorus migration pattern resulting from thermal treatment of an oolitic-type iron concentrate with and without additives. To this end focused mineralogical and microscopic observations were performed. The results have shown that roasting with alkaline additive drives phosphorus outside the hematite hosting mineral, however it remains evenly distributed inside the volume of the oolites. It penetrates inside the newly formed cementing phases of Al- Na-Si-Fe-type and also fills the interstices between the crystals. Other than phosphorus, aluminum, calcium and iron tend also to migrate towards the amorphous-type cementing phase. Finally, the possibilities for P removal by means of magnetic separation and acid leaching of the roasted concentrate were evaluated. The obtained final product presents a standard iron concentrate suitable for steelmaking with its phosphorous being dropped from 0.71% to 0.05% and iron grade of a nearly 66% being reached. INTRODUCTIONSignificant proven reserves of iron ores are still not exploitable due to lack of an economically viable and efficient technology for removal of phosphorus. Among them are the oolitic iron ores with high phosphorus which are estimated to nearly 377 billion tons (Hernandez et al., 2012). Phosphorus is a deleterious component giving a cold shortness to steel and often is penalized if exceeding 0.07%. Most of the high-P iron ores are considered refractory since phosphorus is finely disseminated and is evenly met as phosphate groups inclusions inside the limonite structure. Studies on inclusion of phosphorus in artificially synthesized goethite have shown that it is adsorbed as [HPO4]2- groups bridging the adjacent iron ions (Parfit et al., 1975). The high-phos iron ore originating from Lisakovsk deposit, Kazakhstan presents a similar mineralogical issue because the quantity of P, met as solid solution, is substantially higher than the one in P-containing minerals. A potential reason for that is the ore body formation process from the slow deposition of iron-rich precipitates together with clastic erosional sediments in rivers. There is significant quartz and clays inside and around the oolites. The deposit contains about 1.7 billion tons of measured and indicated reserves at 35–41% iron and 1.1 billion tons of inferred ore have been delineated possessing nearly the same chemical composition (Golubovskaya, 2003; Kokal et al., 2003)."

Jan 1, 2016

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003