Search Documents

By L. V. Chugaev, Y. M. Shneerson, P. V. Zaytsev, I. V. Fomenko, M. A. Pleshkov

"Pressure oxidation (POX) is one of the most common and reliable methods of processing gold-bearing sulfide concentrates. However, when processing concentrates that contain natural carbonaceous matter, substantial gold losses occur due to autoclave preg-robbing. The latter involves formation of gold chloride complexes under typical POX conditions (high temperatures, high acidity and high ORP) and subsequent sorption of these complexes by carbonaceous matter. Naturally, chloride ion plays a significant role in the process of autoclave preg-robbing; its concentration in POX solution has a well-marked effect on subsequent gold recovery during cyanidation of POX residue. The previous research done by SRC Hydrometallurgy showed that autoclave preg-robbing of gold could be significantly inhibited by the addition of mercury(II) compounds to POX slurry. The positive effect of mercury(II) was well pronounced both at high (>20 mg/L) and low (<5 mg/L) Cl concentrations in POX solution. The successful bench-scale laboratory testing was followed by pilot plant trials at Ore Test Facility in Blagoveshchensk, Russia. The present paper provides the results of these trials. The bench-scale testing results were verified; the optimum oxidizing parameters and reagent dosage were specified. The behavior of mercury (II) at POX pilot plant was found to be in good consistency with industrial practice described in the literature.INTRODUCTION Pressure oxidation (POX) is one of the most common, reliable, and commercially proven methods of processing gold-bearing sulfide ores and concentrates. However, when processing double refractory materials that contain natural carbonaceous matter, POX technology advantages are compromised by autoclave preg-robbing of gold. The latter occurs when natural organic carbon and soluble halides are both present in autoclave feed. Strongly oxidizing conditions of POX (high temperature, oxidation-reduction potential or ORP, and acidity) favor formation of gold-halide (mostly, gold-chloride) complexes, which tend to bond with carbonaceous matter. The exact nature and mechanism of this bonding is unknown, but as the result of this, cyanide is unable to leach gold from POX residue and the precious metal is lost to the tails (Axenov et al., 2014; Dimov, Chryssoulis, & Sodhi, 2003; Fomenko, Zaytsev, Pleshkov, Chugaev, & Shneerson, 2013)."

Jan 1, 2017

"2.1. General Considerations and Properties2.1.1. IntroductionOur present knowledge of the platinum-group elements (POE) is extensive, the reason being two-fold. The elements have many uses and, moreover, they exhibit extremely varied chemical behaviour, depending on their state of oxidation and chemical environment. The present chapter reviews a selected body of material which is of particular relevance to mineralogy and geochemistry.Comprehensive treatises on the POE include those by Mellor (1956-1957), Gmelin (1938-1957) and Pascal (1958). The inorganic chemistry, particularly coordination chemistry, has been dealt with in works by Griffith (1967), Hartley (1973) and Livingstone (1975), and the analytical chemistry by Walsh and Hausman (1963), Beamish (1966) and Beamish and Van Loon (1972, 1977). Darling (1973) and Savitsky (1978) have reviewed the metallurgical properties and applications of the metals. Goldberg and Helper (1968) have reviewed the thermochemistry and oxidation potentials of POE systems, and Wagman et at. (1969) have also provided selected values of their thermodynamic properties. The geochemistry of the POE has been reviewed by Yushko-Zakharova et at. (1967), Cousins (1973), Cabri (1974), and Naldrett and Duke (1980).Platinum was used briefly as a coinage metal in ImperialRussia. Otherwise, the principal early use for platinum and its alloys was in the fabrication of chemically resistant apparatus. Subsequently, a large part of platinum production was utilized for catalysts in the sulphuric acid and ammonia industries. Platinum has been replaced by vanadium pentoxide in the manufacture of sulphuric acid, but, in recent times, catalytic upgrading of petroleum and emission control systems for automobiles have opened further huge markets for the metal. All of the POE find uses either as reagents or catalysts in the synthesis of organic compounds, e.g., in the Wacker process, which uses palladium chloride to catalyze the production of acetaldehyde from ethylene. There are, of course, a large number of specialized uses for the elements, particularly in alloys, temperature measurement devices, cancer therapy and so on."

Jan 1, 1979

By David Scott, Denis V. Lachance, Daniel Marcotie

"LocationThe Heath Steele mine is located 50 km northwest of Miramichi, New Brunswick.Brief DescriptionHeath Steele is a 2700 t/d, copper-lead-zinc operation which employs conventional crushing, grinding, and differential flotation.HistoryThe Heath Steele mine is located in northeastern New Brunswick approximately 50 km northwest of the city of Miramichi and 65 km southwest of Bathurst. The massive sulphides containing ore values in zinc, lead, copper and silver were discovered in 1953 as a result of a joint venture between the American Metal Company and the International Nickel Company of Canada. The discovery was named after Mr. Heath Steele, manager of exploration for Amco at the time of the discovery.Mill production began in February 1957; however, the mine was forced to shutdown in 1958 due to depressed metal prices and metallurgical problems. It was re-opened in 1962 and milling operations resumed at 725 t/d until 1968 when the milling capacity was boosted to 1450 t/d and then to 2700 t/d in 1969.OreThe main ore zones are massive sulphides with very fine mineral grain. The chalcopyrite, galena and marmatitesphalerite occurrences are finely disseminated.Liberation is accomplished by grinding to 68% to 72% <400 mesh. Average mill feed assays are 0.8% to 1.2% copper, 1.8% to 2.5% lead, and 5.5% to 6.5% zinc, with 60 to 75 g/t silver."

Jan 1, 2000

By Wignall. T. K., J. De Geoffroy

Statistical models are fitted to the observed distributions of eighteen characteristics of the population of commercial porphyry deposits of North and South America. The statistical base required for the formulation of the statistical models includes 58 commercial porphyry-copper-molybdenum deposits of the Cordilleran Belt from which geological, geometric and economic data were collected. Predictive and composite models are derived from the statistical study to assist explorat10n. planning, engineering studies and fmanc1al analyses as required for the development of new porphyry deposits in the Cordilleran Belt.

Jan 1, 1973

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

By Ben R. Bjorkman

The future is here ? or at least that?s what Mine Planners predicted some 15 years ago ? that by 2004 we would have man-less mines running themselves using space-aged technology. Truthfully, though, there hasn?t been much change in mining methods in the past decade, but thankfully that?s all about to change. The benefits of autonomous ? even Tele-operated mining (especially in narrow-vein ore bodies) are wellknown: increased production hours by eliminating travel time to and from the face, continuous production at the face while crews screen and bolt behind the working equipment, less liability for workers? safety in certain areas, etc. But when plans are put in place to accomplish this vision, things stagnate and production carries on as before. This paper examines the components necessary to make that vision a reality. First we?ll detail the technology required to enable Tele-operation ? even autonomous operation of mining machinery, then we?ll look at what?s wrong with the current way we?re mining, and finally conclude with a critique of the machinery itself.

Oct 1, 2004

By G. B. Harris, C. W. White

A study to investigate the recovery of base metals, notably copper, nickel, cobalt, zinc and manganese from iron-free concentrated chloride solutions using ion exchange was undertaken. In such solutions, apart from nickel and, to a lesser extent manganese, these metals are present predominantly as complex anions, and therefore conventional separation techniques based on cationic resins are not applicable. The results demonstrated that zinc, copper and cobalt can all be separately recovered leaving nickel and manganese behind. Specifically, zinc is a major nuisance element in nickel and cobalt processing, and the testwork showed that it can be preferentially removed prior to copper and cobalt. Selective resins for both copper and cobalt were identified, and it was demonstrated that the strength of the chloride background matrix has a significant effect on the efficiency of separation. An additional major advantage in such systems is that stripping can mostly be effected with water. Finally, some observations are made on the hurdles that must be overcome when attempting to introduce and commercialise new technologies.

Jan 1, 2015

By D. E. Deegan, P. M. Keeley, N. A. Rowson, T. Stachowski

An investigation into the use of Tetronics International’s thermal plasma technology based pyrometallurgical smelting process for the recovery of both platinum and rhenium was conducted. 1000 kg of Pt-Re catalysts containing 0.36 wt% Pt and 0.21 wt% Re was blended with fluxing agents, reducing agents and an iron based collector metal precursor and then fed into a plasma furnace over five individual trials at Tetronics International’s facility in Swindon, UK. Both platinum and rhenium partitioned to an iron rich collector metal phase in the furnace, which formed in-situ and accumulated beneath a less dense slag phase, derived from the inorganic substrate of the catalyst, and was easily separable. The levels of Pt and Re concentration achieved in the iron collector made it suitable for subsequent final refining. Technical recovery efficiencies of =98% for both platinum and rhenium were achieved and the concentrations of the metals in the recovered metal bullion were 2.23 wt% Pt and 1.35 wt% Re.

Jan 1, 2015

By A. H. Ransom, M. E. Robb

The Salmita Gold Mine is located 240 air kilometres northea t of Yellowknife on the east shore of Matthews Lake. Salmita is one of several gold showings which are regionally associated with the steep easterly dipping contact zone between mafic, intermediate and fe lsic volcanics to the west and overlying finely laminated argillaceous sediments to the east. The volcanic assemblage forms a narrow 2 m to 7 m wide north to northwesterly trend ing Belt of Yellowknife Supergroup Archaen greenstone rocks. The contact zone exhibits exhalite character and the increased sulphide content provides a di stinct VLF-EM , IP/Resisti vi ty and/or magnetic signature. Gold occurs at or near this contact in three main settings: associated with si liceous vein-like structures; with finely disseminated sulphides within ericitic altered upper fe lsic tuffaceous unit ; or with quartz in narrow shear zones within the overlying sediment . The B-Vein is of the former type with free mi ll ing gold occurring within a highly sil iceous zone having an average widtn of 1.69 m. Alteration is intense within the immediately su rrounding host lithologies and includes the development of si lica, carbonate, sulphide, sericite and chlorite with minor graphite, epidote. tourmaline and scheelite. The mineable zone above the 4th level (-200 m) ha an average strike of 160 m and is divided into three south plunging ore shoots separated by the regional Salmita Shear Zone in the south and by a low-grade structural hiatus in the north. Production from the B-Vein commenced in August 1983 based on a diluted in situ ore reserve of 140,000 t grading 26.6 git Au . As of December 31, 1985, a total of 131 ,537 t grading 27.8 git Au have been mined at a ra.te of 160 t per day and a 96.4 percent recovery, to produce 3,522 ,000 g (113,227 ounces) of gold . Current (January I, 1986) reserves total 45,500 t grading 37 g/t Au down to the 10th level (-500 m) .

Jan 1, 1986

By J. E. Gill

"The name 'Canadian Shield' is used for a vast area; largely in northeastern; Canada; underlain by Precambrian rocks. The part in Canada has an area; of about 1; 790; 000 square miles. Extensions in Greenland; Labrador; Newfoundland; and the United States bring the total area to around 2; 800; 000; square miles. The boundaries of the Canadian part are shown in Fig. 1.; At its margins; the Precambrian rocks can be seen at many places to; extend beneath a cover of flat-lying Palxozoic or later sediments. Information; from borings in the Plains and natural exposures in mountain-built belts; show that similar rocks form a large part of the continental platform. The; Shield; therefore; is a large exposure of what may be regarded as the foundation; of the continent."

Jan 1, 1954

By C. W. Langenberg, D. E. Macdonald, R. S. Strobl

"The successful marketing of Alberta coals will increasingly depend, to a large degree, on an extensive coal quality information base. This information, at present, is generally based on a deliverable, cleaned coaland is confined to existing mine sites. Coal quality information is not as well understood for raw in situ coal outside of mine sites and even less is known about the geological factors that control it.If new uses and markets for Alberta coal are to be developed, such as gasification, coprocessing, and exploiting high rank coals for combustion, it will be imperative that the coal quality parameters important for these utilizations be known. These parameters need to be known for existing deliverable coals and, just as important, for as yet unexploited in situ coal. Factors such as the Cl, No, K, Co, P and trace element contents should be addressed to meet the requirements of these new utilizations.The geological characterization and explanation of what factors control these coal quality parameters is part of research being done at the Alberta Geological Survey. In-seam vertical profiling has been undertaken within the plains and foothills/mountains coals to determine exactly where coal quality variations occur and why. In the Ardley coal zone at the Highvale Mine it has been found, for example, that the ash content of the mined coal is made up of discrete partings and of microsized particles associated with inertinite macerals. The in-seam characterization of coal seams will lead to a better understanding of in situ coal quality variations, leading to new uses and markets for Alberta coal."

Jan 1, 1993

By P. Kobylin, K. Haavanlammi, K. Valkama

"Base metals and precious metals can be recovered from a nickel matte or nickel concentrate using the Outotec nickel chloride leaching process. The raw material is leached with hydrochloric acid and the metals are recovered by solvent extraction, where ammonia is used to control the pH. Ammonium chloride is regenerated to ammonia and the side product of this step is calcium chloride solution. The regeneration utilizes either calcium oxide or calcium hydroxide. The calcium chloride solution is used to convert sulfuric acid into a hydrochloric acid solution while producing pure gypsum as a side product. The regeneration and reuse of ammonia and hydrochloric acid in this process will have a positive impact, from the point of view of both operating costs and environmental sustainability. This paper concentrates on the test work and technical concept development performed by Outotec to implement and develop chemical regeneration and recycling into a vital part of the nickel chloride leaching process.INTRODUCTION According to a nickel market analysis, the nickel market is expected to grow in the future. Main driver for this growth is the increase in stainless steel consumption as the living standards are equalizing globally. The expected increase in the amount of electrical cars and the need for nickel in the batteries of electrical cars also gives potential for the increased need for nickel in near future. At the moment the use of nickel in nickel-cobalt-manganese (NCM) and nickel-cobalt-aluminium (NCA) Li-ion batteries is in the range of 14 ktpa. It is estimated to increase to the level of 90 ktpa by 2025. In every era of the nickel industry, Outotec has been constantly developing new processes to create environmentally sustainable and economically viable processing routes. The Outotec® Nickel Matte Chloride Leaching process is a great example of a process that is flexible regarding raw material and could also treat nickel raw materials that are difficult for smelters. Outotec’s main options for pyrometallurgical nickel treatment include the Outotec® Direct Nickel Flash Smelting process (DON) and the Outotec® Ausmelt TSL process. The DON process is operated in Boliden Harjavalta Nickel Smelter in Finland. Ausmelt process is in use for example in Daye nonferrous plant in China. In the Outotec® Direct Nickel Flash Smelting Process, a sulphide nickel concentrate is processed in an Outotec Flash Smelting Furnace (FSF). Producing concentrates and processing them by Outotec Direct Nickel Flash Smelting to matte followed by hydrometallurgical refining offers a reliable route from concentrate to product. In the DON process, high-grade matte with low Fe content is produced in the FSF and the valuable metals in the slag are recovered in an electric furnace (EF). The Outotec® Ausmelt TSL process can use a large variety of raw materials (concentrates, secondary material and scrap metal) as feed. Fuel and oxygen are injected into the furnace through TSL (Top Submerged Lance) and this enables efficient smelting. Both Flash Smelting and TSL plants produce nickel mattes, which can be refined with Outotec hydrometallurgical processes."

Jan 1, 2017

By J. W. Kramers, R. A. S. Brown

"Samples from seven test wells distributed throughout the surface-mineable area of the Athabasca Oil Sands have been evaluated to determine the amounts of heavy minerals present and the titanium and zirconium contents. The samples were treated to yield the size distribution of the titanium and zirconium minerals as well as their spatial distribution. The study has shown that heavy minerals are found throughout the surface-mineable area; concentrations range from 0.24 to 2.29 per cent (by weight), with a mean of 1.02 per cent. Titanium and zirconium contents vary throughout the area, and are found preferentially in the finer size fractions. •on the basis of preliminary calculations, the tailings streams from an oil sands plant would provide sufficient feed for a large-scale titanium pigment plant, and the tailings from one plant would provide sufficient zircon feed to satisfy Canadian demand for. metallic zirconium. Variability of the heavy mineral content and composition is such that the heavy mineral potential must be evaluated in detail for each mine site."

Jan 1, 1976

Diverse and considerable energies are associated with mobile equipment operated and maintained on mine sites. Loss of control of these energies is a common cause of injury on mine sites and this is well recognised by the mining industry. In 2006, 4 multi-national mining companies formed the Earth Moving Equipment Safety Round Table (EMERST), with the aim of engaging collectively with the manufacturers of equipment to accelerate improvements in mining equipment design. Originally focused on surface mining equipment, and particularly haul trucks, the focus of EMESRT widened to include underground and exploration equipment. Since 2006, EMESRT has maintained a program of regular visits and other engagements with a steadily increasing number of manufacturers. The membership of EMESRT has also increased, with 15 companies being members in 2012. An initial step undertaken by the EMESRT members was the development of ?Design Philosophies? which drew of the collective experience of mining companies to identify potential unwanted events which cause equipment related injuries and illness. A technique for analysing risks associated with operation and maintenance tasks, the Operability and Maintainability Analysis Technique (OMAT), was subsequently developed and trialled. In 2011, the EMERST members resolved to propose a common form of safe design information to be requested by all members companies during procurement, and the resulting EMERST Design Evaluation for Equipment Procurement (EDEEP) process was launched at MINExpo in Las Vegas in September 2012. The outcomes of OMAT risk assessment and control activities are integrated during this process into a common ?Safe Design Information? template for communication to prospective purchasers. The aims of requesting manufacturers to follow this process are to provide equipment purchasers with a common way of assessing how well the issues in the EMESRT Design Philosophies are addressed in the equipment design; and to provide manufacturers with additional information for use during equipment design. The process involves identifying priority tasks based on frequency and the severity of the consequences of potential unwanted events identified in the EMESRT Design Philosophies; undertaking a task-based risk assessment of priority tasks in conjunction with site-based personnel; evaluating the effectiveness of control measures; and providing information about safe design features in a standardised format.

Aug 1, 2013

By N. J. Duncan

"Coal mining, whether surface or underground, has hazards that make it unique in the field of industrial safety and health. The often soft, faulted and folded sedimentary strata make wall or roof movement a risk to the safe and economic removal of the coal, while the extraction and handling of coal may create an explosion hazard even in surface operations, In Canada, these problems are compounded by the situation of the coal fields which range from deep undersea deposits in Nova Scotia to steeply pitching thick coal seams high in the Rocky Mountains. Climate too can create its own problems, particularly the effect of metals of minus 40°C temperatures, as crumpled dragline booms at prairie strip mines witness. Because of the difficult and sometimes hazardous conditions, Canada's underground colliery managers, in common with those of other Commonwealth coal-producing countries, must have a government ""certificate of competency"" before being appointed as mine managers. Certification of assistant managers (""under-managers"") and foremen (""fire-bosses"") is also a legal requirement for all of Canada's underground collieries, while the province of Alberta requires certification of surface management personnel. Electricians and mechanics who install and maintain the specially designed equipment underground and in hazardous areas of surface mines and processing plants, and mine surveyors who ensure accuracy of the location of underground workings, must also hold government certificates of competency. The requisites for all certification include a minimum work experience and knowledge of coal mining technology and mine safety and health legislation. Despite recognition of the hazards and increasing knowledge of methods of preventing explosions of flammable gas and coal dust in Canada's underground mines, there have been several disastrous explosions such as those at Springhill Colliery in Nova Scotia in 1891 with the loss of 125 lives, at Hillcrest Colliery in Alberta in 1914 with 189 dead, and more recently · explosions and fires in No. 20 and No. 26 Collieries in Cape Breton. Preventing explosions has required developing optimal ventilation techniques, reducing ignition potential, suppressing ignition at source, draining flammable gas before it can enter the air courses, and preventing, or sealing off, autogenous heatings with their associated carbon monoxide or explosion dangers."

Jan 1, 1985

By M. Nagamori, A. J. Plumpton

"Commercial HCl-leaching of magnesite and serpentine yields highly concentrated aqueous solutions containing 25 mass % to 33 mass % MgCl2. The partial molar enthalpies and heat capacities, the ionic activities of Mg2+ and Cl–, and the Raoultian activity of H2O have been assessed for the concentrated MgCl2-H2O solutions at temperatures of 348 to 373 K. These thermodynamic data are used to calculate the pH of aqueous MgCl2 solutions saturated with a Mg-bearing mineral such as magnesite, serpentine, brucite, forsterite, enstatite or talc. On the basis of these thermodynamic data, technico-economic aspects are discussed as to neutralization with pulverized MgCO3, water evaporation from the MgCl2 solutions, and ore composition including such minor constituents as CaCO3, FeCO3 and Fe3O4. IntroductionA major magnesium electrolytic reduction plant operates in Quebec, where another will begin its production in the year 2000. One uses imported magnesite ore as raw material, while the other will utilize local asbestos tailings (serpentine). Both processes produce a concentrated salt solution of 25 mass % to 33 mass % MgCl2 by leaching the ore with concentrated hydrochloric acid. Thus, the two processes differ mainly in the HCl-leach and related operations. After the HCl-leach of the ore, the serpentine process yields about 25 times more wet cake to filter and wash than the magnesite counterpart. A comparative cost-engineering study with respect to slurry filtration and cake washing has been published elsewhere (Blackburn and Nagamori, 1994). By contrast, the present study considers the thermodynamics and technicoeconomics of the HCl-leach itself for both ores."

Jan 1, 1999

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By J D. McDonald

This paper outlines the function of the Safety and Compensation Division of the Mining Association of British Columbia. After a general discussion of safety and the safety program now being followed in B.C., the author goes on to describe the wide-ranging aspects of compensation payments and company assessment rates. Special attention is also given to the problem of silicosis in mining operations. In appendices to the paper, the experience rating plan of the mining industry is compared to that recently adopted for the construction industry. Introduction The Mining Association of British Columbia consists of fifty-five member companies, including virtually all the producing mines as well as the larger exploration, contracting and development companies. On completion of an extensive study of safety and compensation in the mining industry, the Mining Association of British Columbia instituted a Safety and Compensation Division in 1954. The director of the Safety and Compensation Division reports to the Executive Committee of the Association. There are two main functions of this Division. First is the prevenion of accidents by encouraging

Jan 1, 1965

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013