Search Documents

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By John H. Fowler

"Most of the aggregate used in Nova Scotia is produced from numerous glaciofluvial and ice-contact deposits scattered throughout the province. Production from bedrock sources is increasing, with most of the coarse aggregate used in the Halifax-Dartmouth area coming from quarries operating within the metro area.A recently completed provincial sand and gravel inventory mapping program has identified some ""resource-poor"" areas where comprehensive aggregate evaluation programs are underway. Although some areas of the province are experiencing aggregate supply problems, large volumes are exported to markets as far away as Bermuda.IntroductionThe Nova Scotia Department of Mines and Energy has been involved with aggregate resource studies for several years, although sand, gravel and crushed stone are not designated as minerals under the Mineral Resources Act of Nova Scotia. Our role has been to provide the aggregate industry with resource data as well as provide similar information to governmental agencies involved with municipal planning, water resource studies and environmental protection regulations. Several private consulting firms use the information in many of their site development studies.We became involved with aggregates in a rather roundabout way. Several years ago, an outcry from inhabitants of a small coastal community over the removal of sand and gravel from a local beach moved the provincial Department of Lands and Forests to take action to protect provincial beaches. We were asked by the Department to provide information and to suggest alternative sources here operators extracting sand and gravel from beaches could relocate. This request initiated an aggregate inventory survey in southeastern Cape Breton, which was later extended to cover the entire province. The initial provincial sand z and gravel inventory survey provided a series of 1:50,000 maps showing the distribution of sand and gravel deposits in the province."

Jan 1, 1982

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By Stephen Se

Geological assessment of active mine faces enables ore grade control, geological modelling and exploration planning. Monitoring of the mine advancement at every drill-blast-muck cycle allows for effective production management. However, geological assessments are performed infrequently due to the need to travel to active mine faces, and detailed surveys to map the mine progress are performed at the end of the month. Instant Mine Modeller (iMM) is a portable ruggedized stereo-vision system that creates photo-realistic three-dimensional models of underground mine faces on-site. The 3D models are generated automatically within minutes and can be viewed underground and annotated with geological information. The overall ore percentages of the face are calculated automatically for grade control. Annotated 3D models are located in the mine coordinate system and can be imported into mine management systems. iMM allows for daily monitoring of the mine progress and geology, and for re-visiting the mine virtually as it existed. iMM has been deployed in an underground hard rock mine for 18 months, and it effectively brings the underground work face into mine management offices enabling the right decisions at the right time. iMM has demonstrated benefits to various mine processes including grade control, geological mapping, 3D photo-realistic as-built and production volume.

Oct 1, 2009

By E. Pribonic

Failure of a mine material hoist can cause injuries, fatalities and significant infrastructure damage, along with an associated loss of production. Principal causes of hoist accidents are overwind and underwind. Past and present means of arresting hoisting equipment are marginally effective and utilize destructive systems that are not reusable following an arrest. The use of permanent magnet eddy current arrestor technology is proposed; the history and fundamental science of the technology are presented, followed by real world examples and calculations of performance for failsafe, friction-free, instantly reusable eddy current arrestors as applied to stopping a 30-ton ore skip traveling at 16 metres per second. A comparison of existing arrestor types with the eddy current arrestor is included and limitations of the ECA are also discussed.

Jan 1, 2008

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By G. A. Kosick, G. S. Dobby

"This paper presents the principles and application of a recently developed control system for flotation columns and column circuits. The control system uses triple pressure sensors to directly sense zone densities and level, and to help in characterizing the operating behaviour of individual columns. A complete expert system development tool is incorporated within the system to provide the facility for full operator training, an on-line help facility, and a means for incorporating the column behavioural patterns into decision making rules. The system is configurable to any number of columns and can be run in either supervisory mode or direct control through Minnovex PIO software. Additional process signals can be interfaced with the system if desired. Operating experience with the control system on the Minnovex column flotation pilot plant is described.I: INTRODUCTIONColumn flotation cells have been more difficult to control and are more sensitive to circuit changes than conventional mechanical flotation cells. This susceptibility encouraged investigation into various types of control strategies ranging from inexpensive single pressure measurements for level control, to highly instrumented and expensive systems using a variety of control methods.Flotation operators, in many cases, do not understand the column control philosophy or have not been trained to deal with this new type of cell. Some operators have subsequently absolved themselves of the column operating responsibility. Some column cells, for example, have run for hours with slurry pouring over the top or no froth coming off at all.ColumnEX is a column flotation control system which was developed from the viewpoint of an operating shift foreman who wishes to:1. control the column or column circuit through a genuine understanding of what is happening inside the columns, and2. to share this knowledge with his flotation operators and be available to guide them through times of circuit upsets."

Jan 1, 1990

By Eric Konigsmann, Doug Spence, Scott Jones

"The Williams Gold Mine is located in the Hemlo camp of Northwestern Ontario and is one of Canada’s largest gold producers with annual gold production of 400,000 ounces. The operation is owned and operated as a 50:50 joint venture between Teck Cominco Limited and Barrick Gold Corporation.In July 2002, the decision was made to introduce paste backfill produced from mill tailings as the primary backfilling method in the mine and to decommission the existing cemented rock fill system. This required a fast track design to be completed for both a surface paste backfill plant and an underground paste distribution system followed by an intensive construction phase through the fall and winter of 2002/2003. The paste system was commissioned on schedule in late April 2003 and was in full production within 4 weeks of the initial start up. Overall, the project duration was only 42 weeks from initial project release to commissioning and it was completed $2 million under the budget of $14 million.This paper presents an overview of the lab testwork and process flowsheet design, process control methodology and describes the construction and commissioning phases of the project. Preliminary paste plant performance and operating cost data is also presented.IntroductionThe Williams Gold Mine is located in Northwestern Ontario adjacent to the Trans Canada Highway in the Hemlo Gold Camp as shown in figure 1. The mine currently produces approximately 400,000 ounces of gold annually and is owned and operated as a 50:50 joint venture between Teck Cominco and Barrick.The deposit was discovered as part of the Hemlo gold discovery in 1981 which led to the development of three mining operations within a 2 kilometre radius. The neighboring operations are the Golden Giant Mine, currently owned and operated by Newmont Gold, and the David Bell Mine, currently owned and operated by the same joint venture which is running Williams. David Bell ore is blended and milled in the Williams concentrator."

Jan 1, 2004

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By Ronald L. Bruening

IBC has developed a cost effective MRT process for the selective extraction and recovery of gold, copper, and a mixture of other base metals from mine leach cyanide solutions. This is a two-stage system in which the gold is first recovered selectively as a high purity salt. The copper is then recovered separately as a sulfate salt. The other base metals are then collected as a cyano anion concentrate. Three different SuperLig® materials are used. The first stage can be used alone on gold leach solutions where copper and other base metals are not a problem. The two or three stage system is used when the base metals build up in the leach solution, resulting in increased costs. The cyanide or cyanide/cyano anion concentrate can be recycled back to the leach solution until the build-up of other salts, etc. becomes too high, or this too can be controlled with a percentage bleed stream.

Oct 1, 2003

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992

?Why TSM in Canada ?How it was developed ?Architecture and Goverance ?COI panel ?Performance indicators and how they work ?External Verification ?Reporting ?The national organization of the Canadian mining industry ?Mining, smelting and refining of base and precious metals ?Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ?Many associate members ?www.mining.ca

May 1, 2011

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005