Search Documents

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

By Scott SD

The 1986 PACLARK Expedition established that propagation of a seafloor spreading zone into continental crust has created a complex series of volcanic basins on the floor of the Western Woodlark Basin. In addition to abyssal basalts, felsic volcanic rocks were recovered - especially at the leading edge in the extreme west. A recent deposit of hydrothermal Fe-Mn oxides was discovered on an axial seamount of basaltic andesite, and seawater plume anomalies suggest current hydrothermal venting elsewhere. As a modern analogue for the settings in which ancient volcanogenic massive sulfide orebodies probably formed, the Western Woodlark Basin warrants further investigation.

Jan 1, 1987

The geology of an area in north-western New South Wales, bounded by the South Australian and Queensland borders, latitude 32° S. and longitude 14° E. is discussed.The area involved includes sixteen 1:250,000 standard military sheets and covers approximately 96,000 sq. miles.The geology of the Willyama Complex is not dealt with but a small area of metasediments previously included in this unit is separated and a possible correlation with Precambrian to the east is suggested. Torrowangee Group sediments are described and the problem of nomenclature using a glacial implication is raised.Nine areas of proven Lower Palaeozoic sediments are considered and their relationship to the boundaries of the Bancannia Trough outlined. It is possible that some exposures not yet substantiated by fossil evidence may prove to be Lower Palaeozoic rather than Precambrian in age.The sediments of the Lachlan Geosyncline in the area of the Cobar massif are described and new concepts on the age and distribution of some of the established stratigraphic units are introduced. The absence of rocks of Middle Silurian age probably indicates the time of a major orogeny in this area.Lithology, thickness, and distribution of the Upper Devonian sediments is considered and some of the more recently found fish plate localities are listed.Mesozoic sediments occur in isolated areas of Lower Jurassic age and in the Great Australian (Artesian) Basin. A four-fold subdivision of sediments of the basin has been possible in some areas but lack of sub-surface information at present, precludes the possibility of correlation with the type sections in Queensland.Units in the Cainozoic are subdivided and a five fold subdivision of the Quaternary, at present being used throughout western New South Wales, is described.

Jan 1, 1969

Among the various methods of thick-seam mining already well-tried in practice longwall caving with extraction of a single slice, as thick as possible, abandoning the top and/or the bottom coal, seems to be the most suitable one for the Australian coal mining industry. The production units of the future should be equipped with heavy double-drum shearer-loaders, wide armoured conveyors, (with one or two central chains) and shield support. Material of this type has been developed for seams up to 6 m thick. Output figures of more than 6,000 tROM/d from a single face can be looked upon as a quite realistic expectation. The problems of co-ordinating such large production units with the whole layout of the mine are discussed. The factors to be taken into account in the planning work and for preven- tion of mine fires caused by spon- taneous combustion are dealt with. For economic reasons the highest possible utilization factor of the very expensive equipment must be aimed at. Furthermore, the seams or parts of seams to be extracted should be carefully selected.

Jan 1, 1976

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

By Artone E

screening equipment installed in e Hamersley Iron operation is described, and tails of operating parameters and screening - Iia in use are given. Tests were carried out on full-size reens in the operating plants to study the Meets of mat aperture size, feed size distri 1,ution, feed rate, screen speed and throw, angle of inclination, and feed moisture content n screen performance. Sampling equipment was signed so that undersize samples could be htained from various locations along the length of the screen, thus providing information pout the quantity and size of particles passing òhro gh the screen at any point. Conclusions derived from the testwork and relevance of these to the Hamersley Iron aeration are discussed.

Jan 1, 1984

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

In the mid-1990s, after a long period of antipathy between the company and its detractors, Rio Tinto embarked upon an ambitious cultural change program that sought to transform the fundamental basis of its relationship with global, national and local stakeholders. This has evolved into a broader pursuit of positive cultural change within Rio Tinto as part of the mining industryÆs Sustainable Development initiative. Initially driven from the top down, the communities component of this program comprises an architecture of policies, value statements, social research and verification systems. The commitment to better community relationships is best exemplified in Australia by the scope and scale of the GroupÆs Aboriginal land access agreements, community development programs and the work of the Rio Tinto Aboriginal Foundation. While collectively these form the core elements of an evolving set of internal social competencies, development of second-tier competencies is required to organically embed a culture of sustainable relationships with local and regional communities. Second-tier competencies will include appreciation of social dynamics, social science and diversity at middle management level; rigorous social research that properly informs development options for companies and host communities; career paths and recognition within the mining industry for young professionals both generally and from stakeholder communities; proper community-needs assessments, research into such things as purchasing power and other economics data, and inventories of public goods such as land-carrying capacity and water availability. Without this information it is difficult to gain an appreciation of and to alert people to the consequences of change brought on by a mine. The next decade will see second-tier social competencies promoted within successful mining companies. Measures to achieve this include a range of Human Resource (HR) incentives such as recruitment and career advancement based on broad competencies rather than narrow technical proficiency, humanities training for mining professionals and performance rewards that recognise social competence. A sustainable future for mining in a globally connected social landscape requires selection of people who can listen, relate and act in an open social system. The challenge for the mining industry, its professional organisations and educational institutions is to acknowledge this and develop these new aspects of mining industry professionalism. This cannot be left to individual companies if the industry is to have a sustainable future.

Jan 1, 2002

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

By Hayes P. C

In commercial mineral processing operations it has been found that the conditions in the drier have a considerable effect on the subsequent electrostatic separation of nttile and zircon. Laboratory scale studies simulating these heat treatment processes have shown that the electrical conductivity of nitile varies markedly with treatment temperature, time and gas composition. The zircon on the other hand is unaffected. By increasing the electrical conductivity of the rutile, significant increases in separation efficiency can be achieved. Electron microscope investigations have shown the increase in electrical conductivity to be associated with the production of planar defects in the crystal lattice.

Jan 1, 1991

This is the second of a series of papers dealing with Geology in Exploration. The first, published by the Australasian Institute of Mining and Metallurgy, Proceedings Nos. 143-144, 1946, was written as an introduction to the subject and employed the exploration geology of the Cobar field to illustrate the prospect thinking. This paper will be concerned with the problem of ore repetition in depth and borrow its- example from the Mount Lyell copper field. The writing will be taken up altogether by the example. Nevertheless the intention remains to develop the subject in terms of its wide interest and application.The Mount Lyell field possesses large actual and prospective resources within, and in the vicinity of, the known deposits. This paper does not bear at all on these accessible ore reserves and tangible prospects. There is also in this area evidence of deep ore. The possibility is of little practical interest at present. But the picture of ore repetition, exemplified by the Mount Lyell field, does matter now to the outlook on exploration in this country. For once this essential feature of ore occurrence is widely understood there may develop, on the scale warranted, the search for major deposits which do not outcrop but which are still at shallow depths because of the part erosion plays in this story of concealment and exposure of ore. Also there is the chance in some fields (including Mount Lyell) of a second harvest of orebodies within mineable depths. This exploration goal, introduced in the first paper, will appear more clearly as the Geology in Exploration series is written up. Here the concern is to show the character of the geological evidence which points to the occurrence and recurrence of ore in the earth's crust, the picture at the foundation of this exploration scheme. There is considerable information in the Mount Lyell area of the structures...

Jan 1, 1947

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Jacobs M

After a methane explosion in a coal mine a pre-determined crisis management procedure is instigated. As the process rapidly evolves the inevitable question arises - are personnel trapped underground, are they alive and can they be rescued without putting the lives of the rescue crew at risk? This is a very emotive question with many sub-questions such as; could anybody have survived, is there the potential for a secondary explosion and is there a `window of opportunity' before that secondary explosion occurs?To determine if that window of opportunity exists two fundamental elements must be in place; a method of determining the atmosphere at key points in the mine and a method of predicting the course of change of that atmosphere with respect to time. The first element can be achieved if the tube bundle system is intact and drawing samples from known points, alternatively boreholes can be drilled from the surface. The second element can be realised by utilising a sequence of computer generated control charts which have a time axis, a percentage combustibles axis, the upper and lower explosive limits of the current atmosphere and a prediction option which allows the user to look at the potential changes in the atmosphere over a set period of time. These control charts would be part of the mines on-going crisis management system rather than a tool to be used after an explosion had occurred.

Jan 1, 1998

By Paine G. G

The measurement of the fragmentation size distribution of a blast muckpile can be achieved directly by screening the entire muckpile. Screening of muckpiles in a production operation is generally not practical due to the logistics and time involved moving large volumes of rock through a screening plant. An indirect technique to assess blast fragmentation size distributions has been developed. This technique uses photographs of the blast muckpile taken at intervals during the excavation cycle. The images from the photographs are input to desktop computer software via a digitiser tablet. The software compilates the rock fragment sizes and calculates a size distribution. This paper discusses the technique and subsequent data analysis. Examples of the application of this technique for the assessment of comparative blast performance are given.

Jan 1, 1990

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By Meunier G, Davis J, Koperski G

The dry processing of mineral sands concentrates can result in the generation of significant amounts of airborne dust. The radioactive component of this dust has implications within the context of work environment health codes. The last four years have seen considerable investment in dry plant equipment enclosure and dust extraction systems, with resultant reductions in plant ambient dust levels. Simultaneously, an industry wide program was started to examine the origin, nature, mineralogy and radioactivity of the airborne dust. The major findings of this study have been: ò confirmation that monazite was the only significant source of dust radioactivity. ò recognition of two sources of dust: - agglomerates of finely divided ilmenite-rutile alteration products, which are formed by the removal of surface coatings and particles. - abraded mineral fragments, which reflect the mineralogy of the parent particles.

Jan 1, 1991

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By Weining L

In-situ experiments were performed in a tunnel built in loess soil with the displace- ment components of the tunnel lining and the acceleration components of the tracks measured during the passing of trains. The measured parameters were then studied by the spectral method. As a result, the dynamic forces of trains was simulated numerically and a deter- ministic dynamic nonlinear analysis was carried out by means of finite element method. The results obtained by two different approaches were in fair coincidence. Results of the study indicate, that the low and medium frequency components of the dynamic train loading would be crucial for the dynamic responses of the tunnel lining and surrounding mass, and their effects would increase with the speed of passing trains within a certain range.

Jan 1, 1987