Search Documents

By Ross T. J

Renison Limited operates an underground tin mine employing both cut and fill and open stope methods, at Renison Bell on the west coast of Tasmania. Mining in the region commenced in the 1890's. Development of the current mining operation commenced in 1965. The ventilation system used at Renison in its present configuration is a function of current mining methods, orebody characteristics and prevailing Tasmanian Department of Mines Inspection Regulations.

Jan 1, 1988

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

By Yokozawa K, Yamamoto T, Kameoka Y

Japan Construction Method and Machinery Research Institute has been conducting various field surveys of tunnel works and other excavation works, and the cost and efficiency of these two excavation methods have been studied. Based on these data, the costs of blasting excavation and mechanical excavation represented by roadheaders were calculated. The costs were calculated and compared for rocks of various hardness. When the total construction cost is considered, the degree of overbreak becomes one of the most influencial factors, because the overbreak area must be filled up with expensive shotcrete in NATM. So, in the next step, the relation between the excavation costs considering overbreak and the rock hardness was studied using the data on overbreak obtained by the field survey.

Jan 1, 1987

Experimentation with new methods, materials and machines to improve primary drilling and blasting is a continuing practice in the hard rock quarry operations of the BMI Group. These experiments will continue in the remote hope that one day we may produce a perfect feed for the primary crusher. As this day is still a long way off, the necessity to break oversize boulders will be a problem to be faced for the foreseeable future. To gauge the efficiency of primary blasting from this point of view, BMI monitor the tonnes of material crushed in the primary crusher for each boulder requiring secondary breaking. Over a period of about 10 years, this figure has improved from 30 tonnes througi the primary crusher per boulder, to 100 tonnes per boulder at our largest operation, which produces in excess of 2 million tonnes per year. Evan with this improvement, 25,000 boulders require secondary breaking each year This paper does not provide the solution to this problem, as like primary blasting, it will have to be constantly reviewed as new products and techniques become available. The paper sets out all of the methods tested or considered for test by BMI and our nnnn1iicinnq nn Chair PffPr.tivPness . Economic

Jan 1, 1978

By Hayashida O, Numata Y

Ultraviolet and infrared spectroscopic analyses and the extended lluckel molecular orbital method were applied to determine the electronic and binding states of 2-mercaptobenzothiazole and the adsorption system of 2-mercaptobenzothiazole on pyrite. 2-mercaptobenzothiazole exists rather in thione form than in thiol forru and the two adsorption peaks in solution were assigned to both 7t--?rt* transitions. 2-mercaptobenzothiazole chemically adsorbs on pyrite mainly due to forming the bond between iron (pyrite) and sulphur (2-mercaptobenzothiazole).

Jan 1, 1993

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

By N Ozawa, R Kaneko, M Arimit

The Mitsubishi Higashitani limestone mine is a ten million tonne per annum operation located near the city of Kitakyushu on JapanÆs western island of Kyushu. Higashitani is one of the largest limestone mines in Japan and accounts for about five per cent of national production. Blasting practices at the Higashitani mine involve the use of bagged ANFO, dynamite primers and non-electric detonators. Regulations in Japan prohibit the use of site mixed bulk explosives. Blast size is usually around 17 000 tonnes with 20 holes in a single row, two or three blasts are fired per day at a powder factor of between 0.25 and 0.32 kg/m3. As part of a program looking at oversize reduction Mitsubishi, Asahi and Orica agreed to conduct a joint project at the Higashitani mine to investigate the relationship between the powder factor and fragmentation. The first stage of the project was to benchmark the current blasting performance. Five blasts were monitored in each of the 210 (hard rock) and 220 (soft rock) areas of the mine. OricaÆs Powersieve« software was used to measure fragmentation and total rock breaker hours were also recorded for each blast. OricaÆs computer blasting simulation model Sabrex« was used to prepare revised blast designs with a higher powder factor and predict their performance. The performance of these blasts was monitored using the same methods.

Jan 1, 2004

By Molloy GR, Eaton RA

The crusher development programme for 7ft Super Extra Heavy Duty (SXHD) Symons cone crushers commenced in 1984. The main objective of the programme was to run the crushers at maxi- mum power for the full life of the liners. This would give a finer product sizing enabling grinding and flotation plant throughput to be maximised. The study was conducted along two basic lines of attack, the first main- taining an effective profile through the life of the liners, the second improv- ing the properties of the liners. It has been found that crusher liner life can be extended and crushing efficiency improved by modification of liner composition and profile.

Jan 1, 1988

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

Mining projects draw together stakeholders with various degrees of experience in managing and assessing financial risk. When this risk is not fully appreciated or quantified, the potential for making decisions not suited to investor requirements is significantly increased. A feasibility study provides key information on project development potential, requiring detailed technical investigations with thorough financial analysis. Centaur Mining and Exploration (CME) owned and operated Cawse Nickel Operations (CNO), one of three Australian projects to develop and process vast amounts of near surface nickel resources. A technical ædue-diligenceÆ and æbankable feasibility studyÆ confirmed the large resource base, newly applied yet tested technology and relatively low unit costs would produce nickel in the lower half of industry operating costs. A number of production variables including capital requirements, delayed start-up, nickel grade, processing, maintenance and product output were outside the feasibility estimate. This was combined with exchange rate fluctuations and lower Ni prices. The inability to generate adequate cash flow and service debt repayments ultimately led to receivership and liquidation of all assets. Following the sale of CentaurÆs gold and nickel divisions, $A 784 million remained outstanding to creditors. This paper aims to define key issues leading to CNOÆs collapse by reviewing feasibility parameters, valuation methodology and project development. Some methods of assessing project viability are discussed with the aim of increasing stakeholder risk awareness.

Jan 1, 2003

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

By Carter LC

Following the perception by the Groote Eylandt Mining Company of a need to further beneficiate a fines product, and preliminary metallurgical testing to demonstrate the feasibility of such beneficiation, a comparison was made of the various configurations of cyclonic heavy medium separators available. This comparison consisted of (i) a pilot plant test in which a dynawhirlpool (DWP) and a pump fed cyclone were compared, and (ii) a survey of operating plants using the systems under consideration. Little metallurgical difference was found-between the different systems. The gravity fed cyclone configuration was finally chosen based on a particular need to minimise degradation of ore and on a desire, in so isolated a location, to use established and locally supported technology.

Jan 1, 1987

By W Dodson

Major ions, d18O and d2H and Carbon-13 concentrations in groundwater from 30 bores near an open pit iron ore mine were used to better understand the chemical evolution of groundwater in the aquifer. The relatively depleted d18O and d2H isotopes of groundwater from various depths suggest that groundwater is recharged from intense rainfall events, with little evaporative effect. The 300 to 500 mg/L increase of major ions relative to that of rainfall is due to evapotranspiration of rainfall during recharge. Geochemical mass balance modelling suggests that the evapotranspiration of rainfall during infiltration through the unsaturated zone varies over six fold from 20 to 130. This coupled with the dissolution of CO2 from the unsaturated zone and partial dissolution of carbonates and gypsum from Tertiary sediments and carbonates from the Wittenoom Formation accounts for the current major ion, d18O and d2H distribution in groundwater. Despite the relatively dissected morphology and steep hydraulic gradient the results of this study highlight the dominance of vertical flow relative to horizontal flow. The study also shows the dominance of rapid recharge by significant rainfall events as an important component of the water budget for east Pilbara aquifers.

Jan 1, 2009

By Mahoney M

For gas content analysis in recent years, it has been standard procedure to report results on a 'dry ash free' (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and sas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types.

Jan 1, 1995

By M Chappell

This paper describes the design of the steel fibre reinforced precast concrete (SFRC) segmental lining for the intake and discharge tunnels for the Gold Coast desalination plant in Queensland. In addition, the key design requirements and design methods for the lining of these 2 km long, 2.8 m internal diameter tunnels, including structural, durability and maintenance requirements are discussed. Details of the segment configuration and erection process are presented along with information on the manufacture and trial testing of the concrete for the segments. The paper also gives a brief introduction to steel fibre reinforced concrete behaviour. Construction of the tunnels commenced in April 2007, and the authors believe this is the first application of this technology in Australia.

Jan 1, 2008

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

Diversification has characterised the mining industry in this country and globally in recent decades, and in Western Australia in particular. One of the most obvious aspects of diversification is technological change which continues at a rapid and sometimes bewildering pace. A function of technological advances is the increased capacity to further diversify the range of minerals which can be identified in economic concentrations and profitably extracted. This broadening of the total base of the industry has a synergistic effect on its further development by extending its geographical spread and increasing scope for decentralised infrastructure. Another aspect of diversification is the corporate thrust towards establishing overseas mining bases for a variety of reasons. Off-shore (sea bed) mining is a further manifestation of increasing diversity, although very much in its infancy.

Jan 1, 1996

By Linkson PB

The presence of residual cyanide in mine tailings and fill sands may, under specific circumstances, lead to acute and/or chronic cyanide poisoning of the environment and individuals. In this paper, the nature of cyanide contained in mine tailings is discussed, along with the circumstances under which such cyanide would become a hazard. A number of methods for cyanide degradation are reviewed in the paper, with special emphasis being placed on biological degradation (due to its low costs and the non toxic nature of the degradation process itself). Recommendations are made as to the best methods of setting up a biological degradation system, for use in mining Situations.

Jan 1, 1987

During the course of an investigation into the fundamental chemistry of the cyanide process, it became evident that the usual method of determining protective alkalinity was not completely satisfactory. T.he routine method for the determination of protective alkali by first removing free cyanide by the addition of silver nitrate, followed by titration of alkali with dilute acid using. phenolphthalein as indicator, can be shown to give correct results only when the alkali is a strong base. For other sUbstances, the alkali so determined is not the protective alkali. In view of the complications associated with the presence of zinc in cyanide solutions the discussion will be restricted in the first place to solutions free from zinc. Until the chemistry of simple cyanide solutions is placed on a quantitative basis it will be difficult to elucidate the behaviour of complex mill solutions.By the use of physico-chemical theory, it is possible to treat certain aspects of 'the chemistry of cyanide solutions in a manner which not only illustrates the important variables involved, but which also shows the need for care in interpretIng results obtained by conventional methods.In the following, comparatively simple systems are discussed; the principles established should be of use in interpreting the behaviour of more complex solutions. The methods described are not intended for routine work, but may be regarded as supplementary to the usual analysis carried out for the control of plant solutions, or as alternatives to be used when the latter do not appear to be satisfactory.

Jan 1, 1948