Search Documents

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

By Nagai K, Moriyama K

Toyo smelter has been making s veral efforts to reduce and diversify energy for dealing successfully with such :n:;rgy problems as the first and second oil crises. ::,specially it is one of th:; most important subjects to substitute oil by alternative: energy source, because oil is expensive and unstable with respect to its supply. t _'hercfore i was decided to propel tnC ezhstitution of coal *jr oil. in the first place, the supple- mental fuel oil in the reaction shaft was replaced by oil to coal in 1981, and then th, fuel substitution of pulverized coal was achieved in the steam superheater in 1984. 3y these fuel substitutions about 7u,' of the total fuel energy at 2oyo smelter has been replaced by coal. in this paper the fuel substitu- tions at loyo smelter are described in detail.

Jan 1, 1987

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By B Siddall, A Gunstone

The use of a partial secondary crushing circuit provides a flexible way to optimise existing SAG comminution circuits limited by rock competency or enables optimal processing of an ore through second hand equipment not specifically selected for that ore. This paper details the process involved in designing a partial secondary crushing circuit using the recent installation at Mt Rawdon Gold Mine in Queensland as an example.

Jan 1, 2004

Selective open pit mining for gold has been in progress at Harbour Lights since the onset of mining in March 1985. Selective mining techniques used are similar to those in other recently opened gold mines in Western Australia. However certain practices have been introduced to accommodate the irregular distribution of mineralisation and comparatively high mill tonnage throughput. These include selective mining with large bucket excavators, sequential waste stripping - ore mining normal to the strike of the orebody and sample line preparation and ripping on bench floors. Application of these selective mining practices at Harbour Lights enables the operation to maintain delivery of approximately forty by 50-tonne truck loads of ore to the mill crusher everyday, with limited rehandling of material through ore stockpiles.

Jan 1, 1986

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

Market forces, particularly iron ore prices, demand that plant operators achieve higher throughput in the worldÆs iron ore beneficiation plants without compromising yields or efficiency. This means that production cost per ton is of paramount importance and that all major pieces of Processing Equipment have come under close scrutiny to improve throughput at their most efficient performance levels and for the longest possible continuous running time. Without doubt the use of modern engineering standards and materials of construction has contributed to matching these throughput, efficiency and availability demands. However, often not enough attention is paid to the so called æinsignificant elementsÆ connecting this metallurgical equipment, such as chutes, pipes or other conveying systems, and particularly to the sufficient protection of their wearing surfaces. The result can be an unplanned and expensive outage caused by the wear related failure of such components. This paper will discuss:the theory of wear and the multiple factors of material and design that contribute to a reduction in wear; and the combinations of modern wear resistant materials available to todayÆs engineer and how, by intelligent selection and correct application, plant availability can be optimised. Examples outlining how these principles have been applied in South Africa showing some improvements leading to increased plant availability.

Jan 1, 2002

Palaeomagnetic work on the red beds of the Hervey Group from central N.S.W., and on the Mount Eclipse Sandstone from the Ngalia Basin, Central Australia, reveals a pre-deformational magnetization from the Hervey Group, which indicates a semi-equatorial palaeolatitude during the latest Devonian or earliest Carboniferous and a syn-deformational magnetization from the Mount Eclipse Sandstone which places Australia at a palaeolatitude of about 70¦ ¦ 20¦S during the early Late Carboniferous. By comparison with the existing data from Australia, the new results indicate that: (1) Australia (and thus eastern Gondwanaland) underwent a rapid southward movement of about 60¦ during the late Early and early Late Carboniferous, (2) the Lachlan Fold Belt has been part of cratonic Australia since at least latest Devonian or earliest Carboniferous, and (3) the New England region and cratonic Australia were at a similar palaeolatitude during earliest Carboniferous, but they may have undergone the rapid southward movement separately.

Jan 1, 1987

By Snowdowne J. B H

Rand Mines, Limited, located in Johannesburg, Republic of South Africa has recently completed feasibility studies which have lead to the initiation of two major coal strip mining ventures. A minicomputer based mine planning system was developed to perform the feasibility studies. The broad approach of this system is to utilise inter.-actively the specialist skills and interpretative abilities of mining engineers and geologists. This paper reports briefly on the outline of the system and at greater length upon certain aspects of its use.

Jan 1, 1977

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

By Marois R, Hauff P, Kowalyczk P, Lipton G, Bedell R, Neville R, Edmundo G, Ehling M, Kern R

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the Short Wave Infrared range of the solar spectrum from 1220 to 2420nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a Quartz- Sericite-Pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By Kurihara K, Tanimoto C

Construction and mining sites are often subject to unexpected flooding and extensive delays may occur in locating and installing emergency pumps. This particularly applies to sites located in remote areas. A simple and effective pump, called an air-lift pump, can be built from the equipment available at the working site. The basic req- uirements are a compressed air supply, air hose and conventional water pipes. The air-lift pump is comparatively in- efficient but approximately 35 per cent of the available compressed air power at the site can be applied to pumping. Suprisingly high liquid discharge rates may be obtained in suitable applications. The theoretical and practical consider- ations of the air-lift pump are evaluated and a suggested procedure for the emergency design and construction is outlined. INTRODUCTION. Sudden inundations of water into mine and development excavations require the immediate removal of the water if extensive and often irrepairable damage is to be avoided. Pumps installed in shafts or tunnels may become un- servicable due to being totally submerged during the flooding. The emphasis is on rapid

Jan 1, 1976

By Gray J, Krouse HR, Changkakoti A, Kwak TAP

The Dachang tin field with more than one hundred million tonnes of ore at 1% tin and 3% Zn is one of the largest tin fields in the world. It comprises five carbonate replacement tin deposits, of which the Changpo deposit containing about 80 million tonnes of ore at about 1% tin is the largest deposit. The deposit, hosted by middle Devonian limestone, argillaceous limestone and black shale, is genetically related to the Longxianggei granite.The oxygen, hydrogen and carbon isotope data of minerals, rocks and fluids suggest a magmatic fluid which evolved during the crystallization of the Longxianggei granite. Mass balance calculations show that the depletions observed in 180 and 13C values of calcites from the ore bodies to the country rocks were due to continous isotopic exchange reactions between the magmatic fluid and the marine limestones at different W/R ratios and between 300 and 600¦C.

Jan 1, 1990

By Partridge A. C

Pinched Sluices, in a variety of guises, are used extensively for the separation of minerals according to density. In the authors' work a pilot-scale sluice has been constructed with provision for splitting the discharge stream into a number of layers. The composition and flowrate of the stream can thus be analysed as a function of depth and the results presented graphically. The effects of such parameters as total flowrate, pulp composition and particle size on overall performance can be clearly seen from such data.

Jan 1, 1979

By Aziz N. I

Examination of the geology and support performance at two site leads to development of an under tanding of the influence of caving on powered support rating. The two site represent the current extremes in support rating, i.e. 6/260 tonne supports operating in the Hirst seam at Solsgirth Colliery, Scotland, and 4/900 tonne supports operating in the Bulli seam, West Cliff Colliery, Australia.A conceptual model considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata.The caving mechanisms identified for the strata of the Hirst and Bulli seams, are different. These mechanisms being related to rock properties - the palaegeography and depositional conditions at each site-produce caved wastes with different yield characteristics.An analysis of the results obtained for convergence and support reaction during production cycles at both sites shows the manner in which support reaction is developed, indicating the importance of higher setting load densities in the Bulli seam.Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations the powered support and the caved waste immediately behind the powered support - further demonstrates the influence of caving mechanisms on support rating.

Jan 1, 1989

Results from current NERDDC funded research into the geotechnology of highwall trench mining methods have clear implications for mine planners in the areas of blast design, trench shape, location of the surcharge spoil and remnant coal pillar design.Adoption of successful smooth wall blasting techniques not only removes safety hazards from the trench face, but limits development of bedding partings at the seam contacts that interrupt the smooth transition of stress across the coal seam.

Jan 1, 1992

By D Thornton

Geologists use large data sets and spend many hours and much computing time modelling the distribution of minerals throughout a rock mass. Significant investments in drilling, assaying and quality assurance and quality control (QA/QC) are made before sophisticated geostatistical techniques are applied to the collected data. A large amount of research has been done in this field such that the ore control model is a reasonably accurate reflection of the mineral that is actually in the ground. However, after all this effort, the mining engineers then work just as diligently to blast the in situ rock mass to a particle size that can be efficiently handled and further reduced by downstream comminution processes. In open cut mines, this invariably requires large amounts of explosive energy that displaces the ore boundaries from where the geologists originally defined them. Failure to accurately account for blast movement will result in misclassification, whether that is ore to waste; low grade to high grade; sulfide to oxide; or other contaminates û collectively referred to as ore loss and dilution. The financial consequence of getting this wrong is substantial and not well quantified. This diminishes all of the good geological QA/QC done in defining the ore. This paper discusses various technologies used to physically measure blast-induced orebody movement and the difficulties in modelling this with a purely theoretical approach. Rock mass structure, blast energy, design and timing contours all have significant and interrelated effects on blast movement vectors. Measured blast movement has a large variance due to the uncertainly of many of the controlling parameters û arguably dominated by the heterogeneous nature of the rock mass. Although there have been significant advances in blast movement modelling capability in recent years, this unpredictable blast movement limits their use in the context of production ore control. Certainly, without physical field measurements, accurate predictions of movement are near impossible.Limitations of traditional surface markers in determining three-dimensional (3D) blast movement within the orebody are also reviewed, and advancements in accurately measuring these vectors within blasted ore discussed

Sep 26, 2011

By Polthier K

A short discussion of the salient aspects of a dispersed flow model in relation to the gas flow in blast furnaces is given. The use of the theory in assessing vessel performance is mentioned. Tracer results of a blast furnace (688 m3) from three furnace levels and different radial positions are analysed and results presented as D/ud values. The significance of the shapes of experimental tracer curves are included and comparison is made with results obtained on other furnaces.

Jan 1, 1975