Search Documents

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

IN this paper the author's intention is to convey a brief resume of the lead flotation treatment and lead flotation machines, which have replaced the May jigs and Wilfley tables at the plant of the North Broken Hill Ltd., and converted this mill into an all-flotation plant.Attention is directed to the fact that this drastic change from semi-gravity to all-flotation treatment, has been successfully accomplished without resorting to finer grinding than that previously in vogue for Wilfley table concentration, viz.: 10% to 16% plus 40-mesh I.M.M. screen.From the figures now available it is manifest that the scheme of all-flotation concentration-new as regards its successful application to Broken Hill ores is resulting in considerably higher-grade lead concentrates, and is substantially decreasing charges for labour, stores, and maintenance.The new treatment is far-reaching in its simplification of plant, as evidenced by the idle jigs and tables, and the results being obtained by North Broken Hill Ltd. may possibly influence metallurgical practice generally in Broken Hill.The outstanding features of the treatment are:(1) The coarseness, and high grade of lead concentrates obtainable.(2) The low time factor required for flotation.(3) The plant capacity, and the simplicity of its operation.(4) The low horse-power consumption.(5) The small cost for reagents used (not exceeding 3d. per ton of ore).

Jan 1, 1930

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

By Slater R

The initial planning and detail design phase leading to the development of a 7.5 m internal shaft to service the deep 3000 and 3500 copper orebodies at Mount Isa, Queensland is well advanced. The choice of internal shaft access was made over alternative methods such as a decline from existing levels and borehole hoisting. The resulting access development requirements and shaft configuration for production have been determined. Several techniques are being studied for shaft development. These include the application of blind shaft drilling and large hole reaming methods as well as conventional sinking techniques. As the 3000/3500 Orebodies extend from 1000 metres to more than 1800 metres below the surface, high stress conditions and ground temperatures ranging from 45CC to 62CC are anticipated. The effect of these on the methods being investigated to create a favourable working environment will influence the final choice. Exploration diamond drilling is in progress to confirm the geology of the orebodies so that planning for their extraction including refrigerated ventilation concepts can proceed.

Jan 1, 1982

By M Battersby, F Parra, S Sanchez-Pino

Pneumatic flotation, as developed by Dr Rainer Imhof, has been applied in commercial beneficiation operations since 1987. Over 85 flotation cells have been installed in more than 30 operations, successfully beneficiating a wide range of minerals. Pneumatic flotation is however still considered as a non-conventional flotation process. Due to its highly selective nature in operation it has generally found its market in difficult applications where conventional flotation equipment has struggled. Compa±fa Minera Huasco (CMH) operates an iron ore pellet plant in central Chile. CMH desired to produce a low silica pellet for the export market where the SiO2 grade should not exceed 1.5 per cent. It is common practice in other countries to float quartz from hematite with relative ease. However, the silicates contained in the magnetite ore of CMH are only present as quartz in small quantities and the major undesirable silicates are difficult to float. CMH spent considerable time on developing a reverse flotation process and a reagent suite to try and reduce the silica content to acceptable levels. However, extensive laboratory and pilot plant tests with conventional mechanical tank type cells and with column cells failed to produce the required reduction in impurities. A series of tests with pneumatic flotation cells indicated that this type of flotation technology could achieve the required silica target. A 500 tph Imhoflot pneumatic flotation plant was subsequently constructed and successfully commissioned by CMH, making it one of the largest iron ore flotation plants in the world. This paper details the background and testing that was undertaken by CMH which led them to choose pneumatic flotation as the preferred process and compares the test results with that achieved in the industrial plant.

Jan 1, 2005

INCREASE OF CATASTROPHE FREQUENCY AND SEVERITYIn the last couple of decades the frequency of natural catastrophes has increased dramatically. This realization results from the statistical analysis of the comprehensive loss data that we have been collecting constantly over the last 30 years and have evaluated in connec-tion with the preparation of our "World Map of Natural Hazards", which is now in its second edition (Munich Re, 1988). Each month brings data on between 30 and 50 new loss events. Fortunately, however, only a few of these have to be added to the list of major natural catastrophes, that is only those involv-ing damage that considerably exceeds what the country or region concerned can handle itself so that substantial na-tional or international aid is required. That is generally the case if the number of dead runs into the hundreds or thousands, if tens or hundreds of thousands of people are rendered home-less and if the total economic loss is in the region of US$ 100 million. These major catastrophes, about which we have fairly comprehensive data even in the case of those that occurred farther back in the past, numbered only 14 in the 1960s but 70 in the 1980s; they there-fore increased over a period of 30 years by a factor of 5. The trend is also very clear when we consider the total economic loss, which - adjusted for in-flation - increased during the same period from an average of US$ 3.7 bil-lion per year to US$ 11.4 billion, i.e. by a factor of 3.1. The insured losses, finally, increased by as much as a fac-tor of 4.8.

Jan 1, 1990

By Bradford NL

The Isa Mine of Mount Isa Mines Limited produces 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore from sublevel open stopes annually. Extraction of the narrow, steeply dipping silver-lead-zinc orebodies requires a strategy quite different to that used in the massive copper orebodies. A range of blasthole diameters, explosive types and initiation systems gives the flexibility needed to adapt open stoping to a variety of situations. Hole diameters from 70 mm to 200 mm are being used, with lengths of up to 100 m common for the latter.

Jan 1, 1982

By Real F, Carvalho P

During the development of the Neves-Corvo Underground Copper Mine, since 1981, inflow of water has been encountered in the mine workings, which consist of a ramp from surface 5 km long, a shaft 575 m deep and access crosscuts through the massive sulphide orebodies of Neves, Corvo and Graga, which are three of the four known deposits up today. Mine-hydrological studies have established the main characteristics of the hydrological system and its evolution in space and time. In a geological setting of low permeability rocks of Paleozoic age, tectonically affected by thrusts and faults, this has involved consideration of the relation with surface and ground water as a result of mine dewatering processes. The hydrological systems are described and summarized in this paper together with the techniques employed to study their origin and evolution, namely hydrochemistry, thermometry, piezometry and isotopic tracers.

Jan 1, 1988

By Campbell Brown G A

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some millions of tons of rich copper-gold ore, averaging about 45%to 50%silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux were required. Unlimited quantities of cheap limestone were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting Operations started with one furnace in January, 1906, using as flux low-grade sulphide ore from the mine, containing very little silica. When the second furnace was blown in this was supplemented by ironstone from small deposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Kabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required-viz., 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1911

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

In 1997, the Australian coal industry through Standards Australia committee MN-001 Coal and Coke recognised the need to produce a Standard giving some instruction on how to inspect and audit mechanical sampling systems. A Guide was developed by sampling subcommittee MN-001-04 and in 1999 the Standard was released as AS4264.5 æGuide to the Inspection of mechanical sampling systemsÆ Coal and Coke. Since that time the author has assisted with other committees in developing the Guide for other commodities such as concentrates and a generic standard for particulate materials. (AS4433.6 released 2000). The Coal and Coke guide is also currently a work item for ISO Standards. This paper is focused primarily on auditing and inspection procedures for coal mechanical sampling systems. It highlights the need for at least a three level inspection protocol where the operators manning the system maintain operational checks, the operators are regularly supervised by the company managing the system and once per year an independent auditor inspects the whole system to ensure compliance with design and standards. It does not cover short- and long-term maintenance of individual systems. With companies already certified to the ISO9000 series, this guide forms the framework to bring the operation and inspection of their mechanical sampling systems into line with these principles.

Jan 1, 2005

INDEX OF CONTENTS.1. Historical.2. Manufacture.3. Heat Treatment.4. Fatigue, Failures.5. Consideration of the Establishment o£ a Central Testing or Proving Station.HISTORICAL.Since the introduction of improved high air pressure drilling machines in the early part of the century, efforts have been made to develop the quality of the rock drill bit, in order to take advantage of the greater increase of power output per unit weight of the machines (1). This resulted in the change from solid to hollow steel in the second decade of the present century (2).As the greatest sufferers from the dread disease of silicosis (3), it seemed appropriate that the South African gold mines should be the first to use hollow drill steel. Since then solid drills have become practically obsolete for mining purposes.Water is used with hollow steel drills not only to keep the cutting end cool, but also to assist in preventing the formation of undue dust during drilling. It is of interest to note, however, that water fed through hollow steel or sprayed into the air is only partially effective in removing fine dust particles a few microns in diameter, which particles are said to be the most potent in producing silicosis (3a).So far as the composition of "straight" carbon steel drills is concerned, a commission appointed by the Johannesburg mines carried out a very exhaustive series of tests on drill steels.These drills were manufactured from steel made by all the standard methods, including Swedish, Bessemer, crucible, openhearth, and, to a limited extent, electric furnace steel. It should be remembered that the commissioners' report was issued in 1913, when hollow drill steel had not yet been introduced. Only solid steel drills were then in use.

Jan 1, 1947

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

By Gunn S. G, Wilson E. G

Studies by Telecom showed that the existing cable tunnel system in the Melbourne C.B.D. required expansion in order to meet the future telecommunications needs of the City. Due to physical locations of the various telephone exchanges in the CBD, together with a necessity to connect into existing ATC tunnels, a network of low cover small sized tunnels was proposed to maintain and extend the existing telephone cable network. This paper reviews the feasibility studies, design criteria and constructional aspects involved in building 5 tunnels (total length of 1850 m) and 13 chambers (4 open cut and 9 underground)-together with ancillary works, which form part of the new cable tunnel network.

Jan 1, 1981

By Schon RW, Stephens CJ

The Whitsunday Volcanics occupy most of the offshore islands from the Whitsunday Group, southeastwards through the Cumberland and Northumberland Groups, possibly extending to the mainland adjacent to Shoalwater Bay, a distance of 370 km. Some of the islands of this group are granitic, but preliminary Rb-Sr data indicate these to represent Permo-Triassic basement. Cretaceous volcanism is interpreted to have occurred during initial rifting prior to the continental breakup of northeastern Australia and subsequent development of the Tasman Basin.The volcanics comprise mainly lithic ignimbrites, with local development of inter-bedded surge and bedded tuff, accretionary lapilli tuffs, lithic concentration zones, and lag deposits. Isolated fluidual rhyolite and dacite domes occur. The deposits are considered subaerially emplaced. A Rb-Sr isochron age for volcanism of 110 Ma is determined from new data. The total thickness of the volcanics is unknown, but a minimum thickness of 4-5 km on Whitsunday Is. is suggested. Eruptive centres are inferred to be distributed throughout the volcanic zone. The volcanics are cut by numerous, dominantly near N-S, dykes ranging from dolerite through to rhyolite in composition.Chemically, the volcanics and dykes exhibit a continuous range of compositions from basaltic andesite, through andesite, dacite, to rhyolite, with minor more alkalic compositions. Phenocryst mineralogy in the silicic rocks is mainly plagioclase, augite, and Fe-Ti oxides, with less frequent quartz and hornblende occurrence. Sr and Nd isoptic compositions for volcanics and dykes are close to mantle values. These data are tentatively interpreted in terms of a lower crustal magma arc source separated from the mantle only a geologically short time prior to Cretaceous magmatism.

Jan 1, 1990

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By J McNee

Pike River Coal Limited (PRCL) is developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine is being developed to extract a coking coal deposit of the Brunner Seam, some 46 km northeast of Greymouth, using a combination of continuous miners, road-headers and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumped down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.   PRCL faces significant challenges to achieving the goal of cost effective production. The remoteness, high rainfall (greater then 6 metres per year on average), temperature variation and restrictions on access to this subalpine environment have driven the project to develop some distinctive solutions. These include the establishment of survey control in such a difficult environment with vertical and sub-vertical rock faces, significant vegetation and steep slopes by using helicopter survey, aerial photography and LIDAR (Light Detection And Ranging) aerial survey. PRCL has also commenced designing the placement of the main ventilation fans in an underground chamber in the stone drive.

Jan 1, 2007