Search Documents

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Cryolite, sodium aluminum fluoride, Na3AlF6, is a rare mineral which has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. History Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in sixteenth century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open-hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and II. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940s were outstanding technological advances that facilitated increased production. Recently, pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. Uses of Fluorspar Fluorspar is used to make hydrogen fluoride, also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride (HF) is produced by reacting acid grade (97% CaF2) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation, the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, which is an ingredient in high-octane fuel for aircraft and automobiles, in steel pickling, enamel stripping, glass etching and polishing, and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 50 to 60 lb of fluorine content in synthetic cryolite and alumnium fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly.

Jan 1, 1983

By C. P. Heiner, C. S. Westerberg

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders' wealth). This value or wealth is represented by the market price of the firm's common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm's common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market's perception of the company's progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm's stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company's stockholders and will have an effect on the market value or price of the firm's common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

By Frederick M. Becket, Russell Franks

In a recent article,l which described the softening effect of columbium in plain high-chromium steels, the authors stated that their investigations had shown columbium to be also a particularly valuable inhibitor of intergranular corrosion in steels of the 18 per cent chromium, 8 per cent nickel type. It is the purpose of the present paper to record some of the results obtained through the introduction of columbium to the austenitic chromium-nickel steels. The damaging effects of this type of corrosion have become so widely known as to restrict considerably the applications of the steels under consideration, and therefore there is little question of the importance of the goal to be attained. Numerous contributions concerning the susceptibility of the austenitic chromium-nickel steels to intergranular corrosion have appeared during the past few years, and among others who have dealt constructively with the subject are such well-known authors as Strauss and Houdremont of Germany, Hatfield of England, and Bain in the United States. Different theories have been propounded as to the cause of intergranular corrosion, and various remedial measures have been proposed, the majority of which involve the use of addition agents. Titanium is the addition agent at present most generally employed, as suggested by Houdremont and modified as described by Bain, Aborn and Rutherford. Little has been published on the effects of holding these steels for long periods at the relatively lower temperatures in the presence of corroding media, and the effects have mot been fully realized by producer and consumer.

Jan 1, 1934

By W. A. Forbes

PAGE Introductory............357 ReasoNs for Gas Cleaning.........358 First Methods of Separation of Dust.......359 Amount of Dust Produced by the Blast Furnaces of the United States Steel Corporation During 1912.....359 Dust Content in Blast-Furnace Gas.......360 Primary Cleaning. Dry Cleaning: General Remarks..........360 Braasert- Witting Whirler........362 Brassert Modifications of Brassert-Witting Whirler....363 Dyblie Whirler..........363 Remarks on Efficiency of Dry Cleaning......366 Wet Cleaning: Zschocke System..........367 Duquesne Tower..........367 Bian Gas Washer..........369 Final Cleaning. Wet Cleaning: Theisen Gas Washer.........371 Theisen Disintegrator Gas Washer.......372 Schwerz-Bayer Disintegrator Gas Washer..... 374 Fowler & Medley Vertical Gas Washer......376 Feld Gas Washer..........377 Reco Centrifugal Gas Washer........379 Sepulchre Gas Washer.........381 Dry Cleaning: Halberger-Beth Gas-Cleaning System......382 Smith.Bagley Gas-Cleaning System,......384 Howard Dust Separator.........387 Possible Separation of Dust by Electrical Precipitation ... 389 KapnOGraph............389 Methods of Determining DUst in Gas.......389 Advantages of Clean Gas.........393 Introductory. During the early stages of blast-furnace practice. the gas formed in the furnaces by the combustion of the coke used in smelting the ores was allowed to escape into the atmosphere. The light furnished

Jan 1, 1914

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

By Paul Foote

The temperature of a material may be ascertained by measurement of the intensity of the radiant energy it emits. This measurement may refer to the radiation of all wave lengths emitted by the material, or, if the material is glowing, the measurement may refer to the visible light emitted, or to the radiation in n very restricted portion of the visible spectrum. In general, the intensity of radiation depends not alone upon the temperature of the source, but, also upon its nature. Thus, glowing carbon appears to the eye about three times as bright as glowing platinum, at the same temperature. This is technically expressed by saying that the emissive power or emissivity of carbon is about three times that of platinum. A material having the highest theoretically possible emissivity is known as a "black body;" it is customary to assign a numerical value of 1 to the emissivity of a black body. A black body is experimentally realized by uniformly heating a hollow enclosure and observing the radiation coming from a small opening in the wall. The intensity of radiation emitted from this opening depends only on the temperature of the walls, and not on the material of which they are constructed. If E is the emissivity of any non-transparent material and R is its reflection coefficient, it can be shown that E + R, = 1. If a material having an emissivity of, say, 0.40, and hence a reflection coefficient of 0.60, is placed inside a black body it becomes indistinguishable from its Surroundings, because the total intensity of radiation leaving the material is the same as that emitted by the black body. While the material actually emits only 40 per cent of the intensity of a black body at the same temperature, 60 per cent. of the radiation falling upon it from the walls of the enclosure is reflected. However, if the material is removed from the black body and placed in the open air, the reflected intensity is no longer present and the object appears but 40 per cent. as bright as a black body at the same temperature.

Jan 8, 1919

By W. D. Keller

THE high-alumina clays of Missouri are interesting for several reasons. They are the only sedimentary deposits in North America of first grade (over 70 pct A1,0,) diaspore and boehmite sufficiently large to be mined commercially. Mineralogically, they are composed of diaspore and boehmite in intimate coexistence, but gibbsite, the common hydrated alumina mineral in bauxite and laterite, is absent, or is exceedingly scanty if present.* Therefore, the Missouri high-alumina clays do not represent typical laterization. The physical chemistry leading to their mineral genesis, and the geolbgical setting for their formation, present important problems for scientific study. The origin of the Missouri high-alumina clays has been discussed in earlier reports by Allen1 (1935) and McQueen 8, 9 (1929, 1943). These investigations were made under difficult conditions, however, because no diaspore deposit had been opened where a Paleozoic (Pennsylvanian) rock cover lay undisturbed over the high-alumina clay. The relationship of the clay to only the underlying rocks could actually be observed. Lacking the guidance of critical postdepositional geologic evidence, undue and erroneous emphasis was placed on the postdepositional leaching of the deposits in the theories on the origin of diaspore and boehmite from clay (hydrous aluminosilicates) . With new geologic evidence at hand, a clearer picture can be made for the origin of the Missouri high-alumina deposits. In this paper the geology of a diaspore deposit whose original Paleozoic cover had not been eroded will be described and interpreted genetically. The close relationship of boehmite and diaspore (also with kaolinite and a chloritic mineral), will be established. A theory of origin for the high-alumina clays, consistent with the new data, will be postulated.

Jan 1, 1952

By John Drew Ridge

For the early conservationists before the first decade of the twentieth century, conservation meant largely the planned preservation of water, forest, soil, and wildlife resources-renewable natural resources-through efficient use. Water was primarily thought of as a resource that must be kept available for humans to enjoy in a recreational sense and as a habitat for wild animals, birds, and fish. Little thought was given to conserving water for actual human or industrial needs. If industry entered the picture it was as an actual or potential polluter of water, which was the basic necessity for drinking and bathing and for outdoor recreation. Even the forests were only held worthy of conservation largely because they were areas in which wildlife could, or should, abound and in which human beings might find relief from the cares and problems of everyday life. Finally, the soil was to be preserved in its natural fertility through proper fertilization, cultivation, and crop rotation; in this the conservation program did enter the realm of the practical. For through soil conservation, the world was to be able to raise increasingly large crops of constantly improved organic foods which the steadily growing population of the earth was to need to survive and improve. Relatively little time, however, was spent on considering what profit the farmers of the world were to make from the scientific farming on which they were to embark. In short, the appeal of the early conservationist program was much the same as that of the entire era of Theodore Roosevelt of which it was a part; it was to the heart rather than to the mind; it was to emotion rather than to reason. Because of the way in which the problem was approached, conservation took on the character of a crusade rather than that of a practical plan for the betterment of man through economically sound methods of improving his environment and the uses he makes of it. Conservation had, then, all the advantages of a stirring appeal to the emotions, but it did not have the lasting results that would have been achieved by a program with a sound economic basis.

Jan 1, 1959

By M. H. Loveman

The orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°201, about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Syrnes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 anually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The . closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 1, 1917

R. F. McELVENNY.- The next item is: "Center and other methods, vs. side charging." That was all discussed in the Carson case, and I do not know but what many of the plants are still using center charging. Some are using side charging. Did I understand that where you use the wet charge it is all side charging on the wet ore? B.-G. C. HONEYMAN.- We were on center charging for about a year with wet ore. R. F. McELVENNY.- Then you went to side charging. Has anyone any remarks to make on side versus center charging? E. A. BARNARD.- We have one side and one center, both on deep bath. It is an experimental proposition so far, but the side charge looks very favorable.. R. F. McELVENNY.- This is with calcine? E. A. BARNARD.- This is with calcine on a floating charge proposition.. They are both water jacket. The charge acts very similar on both center and side charging. The calcine spreads much the same as it does on the center charge. It will run down 75 ft. on the furnace side as well as the center. The advantage is in taking care of secondaries and things of that nature. C. BARDWELL.- Do you get any side wall protection from it? E. A. BARNARD.- No. R. F. McKENZIE.- Do you not project the side wall up to protect the skewback? E. A. BARNARD.- There is a slot projection down around the top of the bath; but the repairs on the side wall have been practically the same; that is, they, have been practically the same as they have on the center charge. A. H. RICHARDS.- A point I would like to make is that if you have any doubt about the center charging, we feel that we get better tonnages and lower fuel ratios and better slags with center charging than we ever got with side. Different kinds of charges would, of course, vary, and I could readily see that if you had the same advantage with deep bath smelting that you mention you would probably get just as good a slag and as good fuel ratios. E. A. BARNARD.- In fact, I think the calcine charge spreads more on the side than on the center charge. A. H. RICHARDS.- If you maintain a deep bath. E. A. BARNARD.- That is one thing we have to be careful about, to hold the charge back.

Jan 1, 1930

By J. Volney Lewis

The following paper is based chiefly on work done for the North Carolina Geological Survey, and is presented here by permission of Professor J. A. Holmes, State Geologist. It represents, in a very general way, the field-results obtained during the summer months of 1893, and 1894, and part of 1895; and the portions pertaining to North Carolina are, to a certain extent, abstracts of a report shortly to be published as Bulletin No. 11 of the State Survey. Less emphasis, however, is here laid on the petrographic descriptions of the peridotites, and more detailed treatment is given to subjects pertaining to methods of mining, cleaning, and utilization of the commercial product, corundum. Some of the most extensive fields for investigation which this subject presents have been scarcely more than suggested.

Jan 1, 1896

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi- [ ] fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By W. A. Dickinson, H. F. Hendershot

THIS paper is a brief discussion of the past and present methods employed by the Huntington Works of The International Nickel Co., Inc., in the production of nickel and high nickel alloy seamless tubing. The various operations for both hot and cold processing will be considered in their natural sequence, together with the processing characteristics of the high nickel alloys and some descriptions of the equipment used. The tools and lubricants currently in use will be described. This discussion will relate primarily to nickel, Monel,† and Inconel,† since these are the most common of the many alloys processed into tubing at the Huntington Works. The nominal compositions of the materials are shown in Table I. CONVERSION FROM SOLID BILLETS TO TUBE SHELLS History The commercial production of seamless nickel and high nickel alloy tube shells is a comparatively recent development, the first nickel shells having been produced in 1922, Monel in 1930, and Inconel in 1931 on rotary-type piercing mills. Rolled or forged billets, ranging from 3 ½ - to 7 ½ in. diam, were pierced to produce shells ranging' in size from 4 3/8 in. OD X 0.180 in. wall to 8 3/8 in. OD X 1.0 in. wall. After piercing, the shells. were further processed by hot rolling, reeling, and sizing. Subsequent to these operations the shells were either supplied to the trade as "hot finished" tubes, or were processed by cold drawing to smaller sizes at the Huntington Works of the International Nickel Co. The extrusion of nickel and high nickel alloys also may be classed as a relative newcomer to the field of hot-forming methods, for it was not until 1928 that the commercial extrusion of these alloys was begun on a 600 long ton vertical extrusion press installed at Zenith Works of Henry Wiggin and Co., Ltd., Glasgow, Scotland. This press did considerable pioneer work and the results were so favorable that in 1937 a -2200 long ton horizontal press was installed. The quality of the inside surface of the tubing produced on this press was superior to that produced by piercing on a rotary-type mill and, as a result of this experience, a 4000 ton horizontal extrusion press was installed at the Huntington Works in 1943. Billet Preparation The first step in the extrusion, process is the selection of ingots with good hot malleability, as indicated by the test described by Martin and Bieber.1 Ingots then are forged into rough rounds which are machined to the desired billet diameter on a "bar peeler." This machine consists of a rotary head which carries the cutting tools and is driven by a 200 hp, dc motor. The feed mechanism consists of hydraulically driven input and output carriages on the respective sides of the cutter head. The diameter of the forgings used and the machined size or "billet diameter" that corresponds to the four different sizes of

Jan 1, 1951

By Harold V. Pearce

(Chattanooga Meeting, October, 1908.) THE fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant; and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the " Pearce " method for the separation of gold. At all events, it removes the business reasons which have prevented hitherto the publication of the principles involved. At the suggestion of Dr. Raymond, Secretary of the Institute, my father, Richard Pearce, the former manager of these works, has requested me to prepare a brief description of this process for the benefit of our members. Since I severed my connection with the Boston & Colorado Smelting Co. some time ago, I am indebted for some practical details to the present superintendent, Charles Rees, whose friendly assistance I would gratefully acknowledge. With regard to the history of the inception and development of this process by its inventor, Richard Pearce, I cannot do better than quote freely from his own notes and papers. HISTORY OF THE PEARCE PROCESS.' "In 1874 my entire time was directed to the improvements and additions to the plant at Black Hawk. The changes which I had made in the construction of the furnaces at Black Hawk proved so beneficial that I was requested to introduce the improvements at the branch works at Alma. These changes were carried out as speedily as possible, and proved of great advantage as compared with the old system. "The separation and refining of the gold from the matte now engaged my attention, and since previous experience in the treatment of gold-bearing matte and

Feb 1, 1909

By C.A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By Scott Howard

MANGANESE being perhaps the least expensive of the metallic alloying elements that can be advantageously added to iron in considerable quantities, the basic characteristics of its alloys with iron are properly receiving much attention at present. In the course of a dilatometric investigation of this system several years ago, the writer observed certain transformation phenomena not found in other iron-base alloys. The interpretation of those effects was not evident from the information then available, but recent X-ray studies clear up at least one anomaly and permit a more satisfactory description of the results than would have been possible otherwise. Aside from the new phenomena observed, the effect of manganese on the Ar3 transformation is of timely interest because of its bearing on the critical compositions of austenitic alloys, the applications of which are now being greatly extended. It is known that the properties of these alloys are unstable unless the Ar3 transformation occurs at a temperature considerably below atmospheric and that manganese is very effective in depressing the temperature of this transformation. The writer aims to establish a simple general relation which expresses the location of Ar3 quantitatively in terms of the content of the common alloying elements used in steel. A step in that direction is taken here. Early dilatometric investigations1 indicated that only one transformation other than the eutectoid A1 occurs in the high-iron alloys of the iron-manganese system. Dejean represents the Ar3 point as falling to 0° C. with a manganese content of 11 per cent and carbon content of between 0.30 and 0.40 per cent. Esser and Oberhoffer,2 using alloys low in carbon (under 0.03 per cent), arrived by extrapolation at 14 percent for the manganese content at which Ar3 is depressed to 0° C. Not until both low carbon contents and alloys having a manganese content

Jan 1, 1931

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946