Search Documents

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By D. J. McAdam, R. W. Mebs

THE technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture, According to the prevalent view,8 the technical cohesive strength of a metal, in any particular state as regards prior mechanical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress.? In two previous papers by one of the authors,14,15 evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.8 In this paper, as in the previous papers,14,15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress." 14,15 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,"' however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average of the three principal stresses.* This influence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers, 14,15 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant conclusions are derived from experimental data obtained by other investigators. They are based chiefly on results of tension tests

Jan 1, 1943

By Hiram Brown

The problem of stress corrosion has been discussed a great deal recently, but many factors have as yet not been clarified. There are many interpretations of the definition of the word, different corrosive media are used, and numerous methods of stressing are utilized. Some quarters believe that the inherent strength of the material under test is the determining factor of its resistance to stress corrosion, while others think that the natural corrosion resistance of the material is the determining factor. This paper is intended merely to set forth the limited experience we have had and to discuss some of the other stress-corrosion tests which have been made with light alloys.

Jan 1, 1945

By Thomas O. Ziebold, Robert E. Ogilvie

Experimental analysis of diffusion samples covering the entire Cu-Ag-Au system at 725°C has been carried out. Experimental coefficients are computed at twenty-eight points in the lermary system. It is found that the direct coefficienl for copper is nearly independent of the silver, content for 1ow-silver alloys and that the cross coefficient for silver correlates with the ther-nzodynatnic properlies. This lalter observalion leads to the conclusion that the mobililies of copper and gold are nearly equal. Thermodynarmic actiuilies for Cu-Ag-Au were computed from binary data and adjusted to be consistent with neasured tie lines across the two-phase region which extends into the ternary diagram at 725°C. Application of these therknodynarnic calculaliorls to the dijftcsion data terifies the Onsager reciprocal relations to the extent that experimental uncertainlies will allow. It is jound that diffusion neav the critical point of the 1200-phase field in the isothermal section at 725°C causes the composition gradients for copper and silver to approach infinity while the direct and cross coeficients become equal. From the standpoint of experimental Procedures, it has been shown that microanalysis of ternary samples may be carried out using a simple expression for the conversion of X-ray zntensily to composilion. The accuracy of' this method has been demonstrated by the analysis of standard alloys and by the reproducibility of composition determinations using differed X-ray lines. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. When only two elements are present there is just one independent composition variable, and the diffusion profile of composition vs distance across a sample must change monotonically through all solid solutions bracketed by the terminal alloys. If two-phase regions are stable for compositions between the terminal values, these must appear as planar interfaces in the diffused sample, with the composition profile exhibiting sharp discontinuities. Adding a third element may alter this picture completely. Because of the additional degree of freedom in the composition, we may see composition profiles which do not change monotonically through solid-solution ranges, and stable, nonplanar phase interfaces. Even though two-phase regions may lie between the terminal compositions of a diffusion sample on the constitution diagram, they will not necessarily appear in the diffusion profiles. In binary diffusion only one coefficient is needed to describe the interdiffusion process. From Fick's law this coefficient relates the diffusive flux of one component to its own composition gradient. In ternary diffusion we must allow for cross interaction between the two independent species. By a linear extension of Fick's law we introduce "cross" or "off-diagonal" diffusion coefficients which relate the flux of one component to the composition gradient of the other independent constituent. Thus, we require four interdiffusion coefficients to describe the transport process in a ternary system. In its most general form,1,2 the rate equation for mass transport by isothermal diffusion in a system of s components states that the diffusive flux of component i, Ji, is a linear summation of all driving forces, Xk, each force being multiplied by an appropriate compliance coefficient:

Jan 1, 1968

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915; Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1983

By C. E. Sims, H. M. Banta, S. L. Hoyt

OVER the past few years, metallic arc welding has been extended to steels of the hardenable type. As compared with other methods of fabrication, production has been facilitated, service performance frequently has been improved, and the overall results have been so favorable that engineers and production men have placed great emphasis on this application of welding. The metallurgist and welding engineer, however, have been confronted with new problems, since, for one reason, the harder steels are more apt to crack and special precautions must be taken if sound joints are to be procured. Some of the factors that are pertinent to this problem are metallurgical, and it is an object of this contribution to discuss steel manufacture and processing methods and to show how their control assists in reducing the hazard of cracking. By this time, the problem of cracking specifically underbead cracking, or "hard cracks," or parent-metal cracks-is well known, and a large amount of work has been published, both here and abroad, dealing with this subject.1 The tests described are made under restraint to facilitate cracking and, are so designed that a semiquantitative, or at least a relative, value of the cracking tendency is obtained. As one would expect, it has been reported that the incidence of cracking increases with the carbon and alloy content of the steel. More specifically, the cracking tendency is said to increase with the hardenability of the steel, though it is now recognized that the situation is not so simple. The phenomenon itself, on the other hand, has been but loosely described, and it is in only broad generalizations that this cracking has been related to steel metallurgy. Thus, while it has been abundantly demonstrated that the hardenable aircraft steel, S.A.E. 4130, must tend to crack when arc-welded, the problem still remains of why two lots of the same composition and the same hardenability can vary so greatly in cracking tendency, or what it is about the prior metallurgical history that so strongly affects the results. Further, while the efficacy of preheating and postheating in preventing cracking is recognized and utilized in production, the mechanism by which they function seems not to have been described. These points are thought to be significant in the production of steel for fabrication by metallic arc welding and, hence, of interest to mill and process metallurgists and welding engineers. Consequently, it is another object of this paper to discuss the mechanism of parent-metal cracking, including the influence of the condition of the steel and the control of cracking by manipulation of the time-temperature conditions during and after welding. A new method of rating the cracking. tendency is also discussed, and the results of the test are related to steel composition and structure or prior history. The work to be described was the outgrowth of work in 1940-41 at Battelle Memorial Institute 0n two projects, one

Jan 1, 1945

By R. Van A. Mills

ONE of the most important problems facing the petroleum industry is the profitable recovery of oil that is left underground by the ordinary methods of production. It is true that vast quantities of oil are being recovered from fields previously considered depleted by the pressure restoration method, the most widely applicable -and most successful means of obtaining greater recoveries that has thus far been, developed. But notwithstanding the progress that is being made in the field applica¬tion of this method there is urgent need for a better understanding of the fundamental principles that are involved. To meet this need the Petro¬leum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., during the past two years has conducted a series of intensive laboratory and field investigations. The larger part of the work has been carried on in the laboratory to supply the much needed information upon fundamental principles, information which few if any of the oil companies are in a position to supply for themselves. In all of this work the Bureau is endeavoring to correlate the results of laboratory investigations with those in the field, using the results of one to guide or check the other. This paper is primarily a progress report, briefly outlining the Bureau's methods of study, the laboratory and equipment in use, the preliminary problems that had to be solved in order to attack the major problems at hand, the methods of attacking some of the major problems, and some of the results of the investigations to date.

Jan 1, 1928

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By M. P. Tixier

In several log interpretation methods, water saturation is evaluated by use of the ratio of the readings of a short spacing resistivity device and a long spacing resistivity device plus information on the mud filtrate and connate water resistivities, which is often derivable from the SP. These methods are valid over a certain range of conditions, usually specified by moderate invasion and R.. greater than R,. Since these methods involve no explicit evaluation of the formation factor, F, the saturafiion so found may be used in the standard Archie equation to derive a computed formation factor which, as a check, may be compared with the formation factor known from other independent measurements. Discrepancies in the two values of formation factor generally indicate that the ratio method is not within its range of applicability. If the computed F is too low, the corresponding S, is too low; if the computed F is too great, the corresponding S, is too great. By means of this "porosity balance" check, and some knowledge of the probable conditions of invasion, the interpretation can often be improved. The poqosity balance check is discussed for the cases of the Induction-Electrical Log Interpretation Method, the Rocky Mountain Method, and the R.,/R, Method. For the first method, a discussion is also given for the case of shaly sands. INTRODUCTION Al though many logging tools are available to obtain a practical value of porosity, the only logging method reflecting the water saturation is electrical logging. Water saturation is commonly computed from electrical log data by means of the basic Archie formula, Where F is the formation factor, R, the resistivity of the formation water, and R, the true resistivity of the formation. One difficulty in this procedure is a possible error in the evaluation of R, from the logs— for example, in the case of very deep invasion. There is no possibility, inherent in the procedure, which would provide a check of the accuracy of R, and, hence, of the computed saturation. Other approaches have been proposed which are based essentially on the ratio of the readings made with two dzerent devices: one device, with a short radius of investigation, provides a value close to the resistivity of the invaded zone; the second device, with a long radius of investigation, gives a value close to the true resistivity of the bed. By these methods, the determination of saturation is made independently of any direct knowledge of the formation factor. Therefore, if the formation factor (or porosity) is known from other sources (core analysis, neutron log, MicroLog . . .), it becomes possible to take advantage of this additional information in order to check the value of saturation derived from these latter methods. Inasmuch as this proposed check procedure relies on a knowledge of the value of formation factor or porosity, it has been deemed appropriate to call this verification a porosity balance. The purpose of this paper is to discuss the principle and the application of the porosity balance, depending on the method of interpretation being used. Basis of the Method There are in existence three interpretation methods by means of which the water saturation can bc found without a knowledge of the formation factor (or porosity). As just stated, they are based on the fact that the ratio of the two resistivities (one measuring the resistivity close to the hole, the other measuring the resistivity far from the hole) is independent of the formation factor since it affects the two resistivity measurements in the same way. Chronologically, the resistivity ratio methods are: (1) the Rocky Mountain Method, which has been used since 1943 and was explained in a paper in 1949;' (2) the R../R, Method or Shaly Sand Method, presented in 1954, which permits the calculation of the water saturation in both clean and shaly sands2; and (3) the Induction-Electrical Log Method, presented in 1957 for the interpretation of the induction-electrical log combination." Each method requires certain definite conditions in order for the interpretation to be reliable. The porosity balance method will let us know whether these conditions are fulfilled. In clean formations we know that the fundamental Archie relation (Eq. 1) must always be verified. This relation can be rewritten:

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company's Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By Y. S. Bonillas

Page I. Introduction.......................... 286 II. Physiography.......................... 286 : 111. Introductory Geology...................... 287 IV. Rocks of the District ...................... 288 (A) Sedimentary Rocks..................... 288 Pinal Schist ........................ 288 Bolsa Quarteite....................... 289 Abrigo Limestone...................... 290 Capping Quartzite..................... 291 Martin Limestone...................... 292 Escabrosa Limestone .................... 295 Naco Limestone....................... 296 Cretaceous Deposits..................... 296 Glance Conglomerate................... 296 Morita. Mural and Cintura Formations........... 297 (B) Igneous Rocks........................297. Pre-Cambrian Granite.................. 297 Pre-Cretaceous Granite Porphyry............. 298 Rhyolite........................301 Other Dikc Rocks.................... 301 V. Structural Geology........................ 304 General Structure of Mule Mountains............. 304 Fault Blocks and Other Divisions............. 304 Igneous Rocks...................... 312 Copper Queen Block..................... 313 Fault Blocks...................... 313 Intrusions....................... 315 Don Luis Block....................... 315 Intrusions and Orebodies................. 316 VI. Geologic History......................... 316 VII. Metamorphism and Mineralization................. 318 General Metamorphism.................... 318

Jan 1, 1917

By F. C. Langenberg

It is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy -and Cornu-Thenard justify the assumption that the precision obtained by this machine is comparable to that obtained by the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cofnu-Thenard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several years, and is now employed for both routine and experimental testing.

Jan 1, 1920

By E. C. Lee

THE safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. This fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossment in earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual-cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 10, 1917

By F. C. Bond

Since the Third Theory of Comminution was presented eight years ago (I) it has found increasing use in crushing and grinding problems. The practical utility of its wok index equation is quite generally acknowledged (2). However, its theoretical basis has been questioned in at least three technical articles (3) (4) ('). The purpose of this paper is to present experimental proof that it is scientifically correct. Particles under compressive stress are strained and deformed. They absorb strain energy, and when this locally exceeds the breaking strength, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends and splits the rock, releasing the strain energy as heat. The initial energy flow causes additional crack tips in highly strained areas. If the compression is rapidly applied by impact, crack tips may form before the strain energy has reached equilibrium in the particle, thus decreasing the total work input required for breakage. The energy necessary to break is essentially the energy necessary to produce crack tips, since the energy necessary to extend the cracks to breakage is already present as strain energy in the deformed particles. After breakage nearly all of this energy appears as heat. The crack length cannot be measured directly. However, in particles of regular and similar shape the crack tip length is considered as equal to the crack depth, or crack extension necessary to break, so that the crack length equals the square root of one-half of the surface area. The Third Theory states that the useful work done in crushing and grinding is directly proportional to the total length of the new cracks formed. It can be confirmed by showing that a constant work input produces a constant length of new cracks when reducing the same material to different product sizes. This is done in the present paper on a wide variety of material. The constant work input was supplied by one revolution of the 12" x 12" laboratory ball mill used in making grindability tests by the Allis-Chalmers method (12) (13) The new crack lengths produced per mill revolution were measured from all available grindability test results at 28, 35, 48, 65, and 100 mesh on fifteen different ores, and were found to remain substantially constant for each ore at all mesh sizes. A new technique is used for the measurement of crack lengths. Size distribution plots of the mill feed and product are made by the Third Theory method (9) and the crack lengths are obtained from these plots by the procedure described in the present paper. The energy input required to produce a unit length is of fundamental importance in the size reduction of brittle solids. The crack length Cr is expressed in centimeters per cubic centimeter of solid material. It bears a definite relationship to the external surface area of the crushed or ground solid. A uniform particle shape must be assumed before the surface area and crack length can be evaluated. In this paper it is assumed that the relationship between the surface area and the particle volume of a particle d microns in diameter is the same as that of cube d microns on a side. The external surface areas of particles with a cubical breakage probably agree approximately with this rule, and correction factors can be applied when physical measurements of the surface areas are available for comparison. However, the assumption of equivalent cubes has been found satisfactory for most calculation purposes. Assuming equivalent cubes, one cubic centimeter of particles d microns in diameter will have a crack length Cr of v30.000/d centimeters, and a surface area of 60,000/d square centimeters. The specific crack length is thus equal to the square root of one-half the specific surface area. Where Sa is the surface area in square centimeters per gram and Sg is the specific gravity of the ground solid, then Cr = vSg . Sa/2 = 173.2/ vd (1)

Jan 1, 1961

By P. D. Merica

ALUMINUM and its alloys have been the subject of much investigation, during recent years, in the course of which the principal features of the constitution of most of the binary alloy systems with aluminum have been determined. Except in the case of a few metals-silicon, bismuth, cadmium, lead, zinc, and tin-an aluminum-rich compound is formed in each binary system, which forms a eutectic with the aluminum or its solid solution with this compound. Thus such compounds as FeAl3, CuAl2, Mg4Al3, and NiAl3 are formed, which are found in aluminum-rich alloys of their respective series as eutectics with the aluminum solid solution. These compounds are, in all cases, hard and brittle and their presence affects profoundly the physical properties of the alloys in which they occur. Within the zinc-aluminum system a compound, Al2Zn3, is formed that decomposes at lower temperatures. Silicon and tin each form a simple eutectiferous series with aluminum; bismuth, lead, and cadmium are only partly miscible in the liquid state with it. The extent of the solubility in aluminum, in solid solution, of these compounds or of the elements themselves, in the case of those series

Jan 7, 1919

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By J. E. Nelson, R. J. Bonnis

Recent completion of Cyprus Bagdad's $240-million modernization and expansion program has registered a 700% increase in ore production with only a 50% increase in labor. Elements of this remarkable achievement include the application of large-scale mining equipment as well as the selection of the latest in processing hardware. Most important, however, was the early recognition that Bagdad's labor personnel is its most important asset.

Jan 4, 1978

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before break-age, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 8, 1950

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887

Jan 1, 1923