Search Documents

By M. H. Pilkuhn, H. Rupprecht

p layers on n-type substrates of GaAs were prepared by difhsion of zinc into these substrates. Experimental details about the diffusion technique will be presented. It will be shown that inhomogeneity in the substrate doping level and crystal shucture defects cause nonplanarity in the junction plane. These nonplanarities give rise to high threshold current densities. From incremental sheet-conductivity measurements the zinc profile is derived. Data about surface concentration and gradient of the zinc concentration at the junction are presented. Finally, some results of laser diodes, which were made of wafers with extremely planar diffusion fronts, are discussed. ThE investigations reported here are part of a program concerned with the materials aspect in the fabrication of GaAs laser diodes. This includes studies of the influence of crystal defects introduced both during the growth of the crystal and as a consequence of subsequent diffusion. Compared with the progress made in the investigation of structure defects, for instance by X-ray microscopy in materials like silicon, no similar results are known so far for the case of GaAs. The further progress in laser diodes will depend very much upon our knowledge of these structure defects and subsequently upon our ability to avoid them. Laser diodes of GaAs had been made mostly by diffusing an acceptor impurity, normally zinc, into an n-type substrate. This procedure was found more convenient than the inverse one for various technical reasons. We will follow this line and restrict ourselves to zinc diffusion only in this paper. DIFFUSION TECHNIQUES AND EXPERIMENTAL DETAIL In order to set a refgrence for our experiments, we used a standard procedure for the diffusion runs. The diffusions were carried out in a sealed quartz tube for 2-1/2 hr at 850°C. One milligram zinc arsenide (ZnAsz) per cu cm of the tube volume served as zinc source. Under these conditions the junction depth was between 25 and 30 p. It is assumed, according to the investigations of the zinc arsenide system by V. Lyons and V. ilvestri,' that ZnAs2 dissociates completely at 850°C into ZnsAsz and Asg. Since there is a condensed phase of ZnsAs2 in the tube at 850°C, the partial pressure of zinc is controlled by the pressure of the arsenic formed by the dissociation of ZnAs2. Due to the fact that the zinc partial pressure resulting from the dissociation of ZnsAsz is only a weak function of the partial pressure of arsenic, the amount of the initial ZnAs2 is not very critical. Experimentally, we found that the junction depth, as well as the surface concentration, was practically the same, if the ingots of ZnAs2 varied between 0.2 and 5.0 mg per cu cm. The wafers were oriented with the main faces in (100). Surface damage due to cutting and lapping was removed by a chemical-etch treatment in a rotating beaker (etch solution: HzSOr, H202, and HzO in a ratio 3:l:l). The GaAs substrate material was n type and doped with tellurium, selenium, silicon, or germanium. It was grown by means of horizontal or Czochralski techniques. After the diffusion process, junction depth and planarity were checked either by grooving with a

Jan 1, 1964

By W. A. Backofen, B. B. Hundy

THE pole figure interpretation in a recent paper' on the torsion texture of copper was questioned in discussion,2 nd a simpler alternative interpretation was proposed. In the hope of reaching a positive decision in favor of one or the other, further studies were undertaken with 70-30 brass and Armco iron. This additional work has not answered all the questions about torsion textures, but the new pole figures do offer support for the original interpretation and show that the texture is more complicated than the alternative suggests. From the previous paper,' the appropriate method of describing the texture in a twisted bar is known to be a pole figure plotted on a plane tangent to the surface of the bar. The axes of the pole figure are chosen to coincide with directions in the tangent plane which are parallel and at right angles to the bar axis (the longitudinal direction, L.D., and the transverse direction, T.D.), for these directions define symmetry axes of the texture. Therefore any ideal orientation that might be selected to represent the texture gives the crystallographic plane parallel to the tangent plane and the crystallographic direction parallel to the axis of the torsion specimen. A unique texture was assumed in the original interpretation, and the four ideal orientations, (112) [111], (111) [112], (110) [001], and (112) [131], were used in its description. Of the four orientations, the first three provide possible slip directions along the direction labeled T.D. in the pole figure, which is one of maximum shear stress in a specimen being twisted. The alternative, however, simply considered the texture to be made up of two components, one a [Ill] alignment along the specimen axis with a random orientation about the axis as in the wire texture, and the other a superimposed orientation (110) [0011. Experimental evidence for this simpler interpretation was derived from two observations: 1—twisting did not alter the orientation of a single-crystal torsion specimen of a brass in which an octahedral plane was perpendicular (and a [Ill] direction parallel) to the axis, and 2—deformation bands with approximately the (110) [001] orientation were seen to develop in the crystal during the test. The new pole figures were obtained with a brass and an iron torsion specimen of 3/4 and 1 in. gage length diameter, respectively. After annealing, polishing, and twisting, seven rods, about 0.030 in. in diameter and with different orientations, were prepared from material near the surface of each specimen; these were required for the method of constructing pole figures by using a Geiger counter as developed by Norton.5 Since the shear strain gradient in plastic torsion is linear, it was readily computed that the material supplying the brass rods had been subjected to a shear strain of about 3.2, and that supplying the iron rods had received a shear strain of about 2. All details concerning specimen design, testing procedure, rod preparation, and use of the Norton technique can be found in ref. 1. Only this procedure was followed in working out the (111) and (100) pole figures for brass, Figs. 1 and 2. However, X-ray photograms were also involved in the construction of the (110) pole figure for Armco iron, Fig. 3. The photograms were made according to the conventional transmission diffraction technique using a small sheet taken parallel to the specimen surface and etched to a thickness of about 0.0025 in. They were especially important in locating the boundaries

Jan 1, 1954

By Charles C. Templeton

Any explanation of the nature of multiphase fluid flow through porous media must ultimately involve a knowledge of the mechanism of such flow through the individual pores of the medium. To provide quantitative information of the latter type, a study was made of gas-liquid and liquid-liquid displacements in single uniform Pyrex capillaries with diameters as small as 4 microns. Quantitative observation of air-liquid displacements with zero contact. angle indicates the adequacy of a model based on Poiseuille's Law and the independence of capillary pressure and interfacial velocity. Consequently, this work discounts previous claims that flow is abnormally retarded in very small capillaries. For the displacement of a very viscous oil by water in a capillary initially filled with water, flow is faster than predicted by the above model. This behavior is probably due to the existence of a thin annular film of water between the oil column and the capi1lary wall as postulated by Yuster. INTRODUCTION The need for experimental observation of the microscopic nature of multiphase fluid flow, to further the understanding of the results of macroscopic flow investigations, has been previously recognized. Chatenever and Calhoun1 in connection with the API Project 47B have extensively studied the flow of fluids through layers of glass or lucite spheres between glass or lucite plates. Lowman2 prepared an interesting film concerning flow in a single capillary, using an apparatus which made a moving interface appear stationary in the field of a microscope. The purpose of the present investigation was to deter- mine what contribution might be made to this field by comprehensive quantitative observation of gas-liquid and liquid-liquid displacements in single capillaries of uniform, very small diameter. The techniques used are similar to those of Lowman but incorporate improvements necessary for quantitative work. Quantitative observations must begin with fluids of simple chemical composition to provide a basis for analyzing the more complex behavior that may be expected with natural reservoir fluids. However, some qualitative observations on systems involving crude oils are presented. Experiments of this sort involve the observation of the velocity of the interface separating two fluids, and have been performed in horizontal or vertical capillaries by several investigators.3,4,5,6,7,8 The most general treatment of their mechanics, by Brittin,9 involves forces due to capillarity, viscous resistance, gravity, an "end-drag" effect, and the rate of change of momentum of the capillary contents. Since the range of pore diameters of interest in petroleum reservoirs is about 0.1 to 100 microns, it was desired to perform these experiments in the smallest capillaries possible, to ascertain whether capillary diameter had any effect on the existing theory based on data from larger capillaries.* It was also important to be able more systematically to vary the direction and rate of displacement than was done by previous investigators. Finally, to concentrate attention on viscous and capillary forces by eliminating gravity as a parameter, this study involves only horizontal capillaries. The work of Eley and Pepper' with a "large" (0.766-mm diameter) horizontal capillary is the previous investigation which is most similar to the present method of quantitative observation. Here capillaries with diameters as small as 4 microns will be studied.

Jan 1, 1955

By I. W. Alcorn

The cost of drilling in the past few years of proration and ever decreasing allowables has received increasing thought and study. It seems to parallel the strides made with respect to pumping problems in 1932 and 1933. Low profit margins stimulate the search for economies. Any discussion of slim-hole drilling involves a multitude of abstract values, and the problem can be attacked only by a study of records and rational thinking. In a measure, traditional methods must be studied with a questioning attitude. The words "slim hole" may be somewhat misleading, as the term is entirely relative. For that reason I wish to define it as used in this discussion. On the Gulf Coast, I would define a normal hole as one in which 10 3/4-in. surface casing has been set and below which a 9 7/8-in. hole is dug. With this as a datum, holes of larger diameter below surface would be called "large holes," with 121/4 in. as the "extra large" class and holes of smaller diameter classed in the slim-hole range, 6 1/4 in. representing about the minimum size. The optimum size has not been definitely determined, but the preference is for a program that would call for setting 8 5/8 -in. surface casing and digging a 7 3/4 - in. hole. Different sections of the country might very properly deviate from this practice because of differences in depth, formations, regulations, or other factors. This paper will be confined to a discussion of the drilling of exploratory wells, as the drilling of this class of wells is quite a different problem from that of drilling a proven field, although many of the same considerations apply in both cases, as will be apparent. Although for many years shallow slim-hole and core-test holes of small diameter had been dug, it was not, I believe, until the fall of 1937 that serious consideration was given to its application in drilling wells 7000 ft., 8000 ft. and 9000 ft. deep on the Gulf Coast. This does not mean that nearly all such wells drilled on the Gulf Coast now are of the slim-hole variety, but only that efforts have been aimed in that direction with very encouraging results and there has been a very definite trend to reduce the size of holes, a trend that probably will continue. As to exploration policy, there appear to be two distinct and opposite views. The one usually followed in the past was more or less designed to "shoot the works" on one well. Generally on the Gulf Coast, the depth at which production might be obtained is limited by the drilling equipment and economics. With this thought in mind, wildcat wells are often planned with the idea of carrying the depth to 10,000 It., or even 15,000 ft. All of the possible hazards are anticipated and the general drilling and casing programs are so predicated. Such wells contemplate the drilling of large-diameter holes; the setting of at least one protective string of casing and an extensive coring policy, all of which finally adds up to an expensive well. AS opposed to this general policy is the slim hole. This, on the Gulf Coast, recognizes that new discoveries represent gam-

Jan 1, 1941

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By R. C. Edwards, Will Mitchell, T. G. Kirkland

THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.1 The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5 ° to 35º from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180° apart. Each successive set is mounted 90º from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, 1x1 ½ x9 in. long, which is attached about 1/ 2 in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1952

By C. M. Wayman, G. R. Srinivasan

A metallographic study of the isothermal products formed between 750° and 285°C was made in an Fe-7.9 wt pct Cr-1.11 wt pct C alloy, and a time-temperature-transformation diagram was determined. The study shows that the austenite decomposes into three different products: pearlite above 540°C, ferrite and carbide between 540° and 300°C, and lenticular bainite below 300°C. No upper bainite forms in this alloy. The results are discussed in terms of carbon diffusion models for upper bainite formation. AUSTENITE transforms into several products depending on the temperature, composition, and rate of cooling, and the various transformation products have been a source of controversy for a long time. Since the classical study of Davenport and ~ain' extensive work has been carried out. The present study concerns the isothermal transformations in an alloy which was used for a detailed investigation of bainite crystallography and provides information supplementary to the work of Lyman and Troiano who studied austenite decomposition in steels containing 1 pct C and varying amounts of chromium. Their work showed that increasing the amount of chromium in high-carbon steels had the effect of depressing the B, temperature and of shifting the TTT curves to longer times and lower temperatures. They further found that if the chromium content is increased in a 1 pct steel to about 9 pct no bainite would form even after a period of 100 days. However, a preliminary investigation by the present authors showed that bainite plates do form in steels containing about 8 pct Cr and 1 pct C. In view of this and some results from a thin-foil electron microscope investigation of the bainite formed in the present alloy: it was considered desirable to investigate the other isothermal products as well. EXPERIMENTAL PROCEDURE The alloy used in the present investigation was obtained from a triply vacuum-melted ingot prepared from high-purity materials. Chemical analysis for the alloy verified the composition to be Fe-7.9 wt pct Cr-1.11 wt pct C. Metallographic observations were made on i by i by « in. specimens which were aus-tenitized at 12 50°C for 50 to 60 hr in evacuated quartz capsules and then water-quenched. Since the M, temperature for this alloy is below room temperature, the homogenizing treatment produced a completely austenitic structure consisting of very coarse austenite grains (ASTM #0-1). Several samples of the austenitized specimens were metallographically prepared and observed for any proeutectoid carbide separation. It was found that all the carbon was in solution. The water-quenched specimens were upquenched and given isothermal treatments at temperatures between 285" and 750°C for varying periods in molten salt or lead baths. The specimens were then water-quenched, and those showing less than 5 pct transformation were used for plotting the beginning of the austenite decomposition. To ensure the removal of the disturbed layer, the mechanically prepared specimens were electropolished in a 1:6 HzS04, CHSOH solution for 10 to 15 sec at 20 v. Final polishing was done with a vibratory polisher using 0.05-p alumina. Various etchants including nital, ferric chloride, and hot ferricyanide (Murakami's reagent) were used to bring out details in the different transformation products. The ferricyanide etch was used whenever the preferential etching of carbides was desired.

Jan 1, 1969

By Albert S. Trube

Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of reservoir fluids well in advance of more accurate laboratory data. One such factor is the isothermal coefficient of expansion of an undersaturated hydrocarbon liquid which may be contained in a particular reservoir. This coefficient, or liquid "compressibility", has often been assumed to be relatively insensitive and nearly constant. Although this assumption may be nearly correct in the case of high specific gravity liquids, it cannot apply in the case of medium to low specific gravity liquids. Any treatment of the nature of liquid compressibilities must give consideration to the variable nature of the isothermal expansion coefficient and the fact that it can be both pressure sensitive and temperature sensitive. The isothermal coefficient of expansion, or compressibility, of a substance is defined as -c = 1/V (?V/?p)T......(1) The value of Eq. 1 may be approximated for a finite pressure change by using the well-known relation, c = V1 - V1/Ve (p2-p1), ........(2) in which p1 > p1 and V2 > V2 and V1 + V2/2. The instantaneous compressibility may also be estimated from the slope of a curve on which log V is plotted vs pa. In this instance, it has been shown that c = In V1/V2/p2-p1 ...........(3) Eq. 3 may be used for variable compressibilities by plot-ting V vs p on semi-log paper. In this case, the instan-taneous or point compressibility is c = 2.303 m.......... . (4) in which m is the slope of the curve at a point in log cycles per psi. ISOTHERMAL COMPRESSIBILITY OF UNDERSATURATED LIQUID In the case of gases, the compressibility has been defined by Muskat' and others as Co = 1/p - ?z/z?p ..........(5) This was later generalized through application of the theorem of corresponding states' to co = 1/pr - (?z/z?pr) T8 ........(6) in which c, is defined as the pseudo-reduced compres-sibility and is numerically equal to (c.p,) and the sign is arbitrarily changed for mathematical convenience. Eq. 6 is general and applies to gases and liquids. In the case of liquids, c. = c1,pe, but if Eq. 6 is used, values of z and ?z/?p, must be determined for the liquid in question. The difficulty of obtaining accurate values of ?z/?p,, particularly in the region where T, is approaching 1.00, was pointed out in the previous paper'. This method of approach is unreliable for extension into computations of liquid compressibilities. On the other hand, c, can also be defined as follows: - Cr = 1/Vr (?Vr/?pr) Tr ......(7) and from which, Cr = 1/pr (?pr/?pr) Tr .....(8) In accordance with the theorem of corresponding states, Vr = V/Vr, p, = p/pr and pr = p/pr. Ref. 2 pro-vides an excellent source of reduced density, reduced pressure and reduced temperature data for a wide variety of fluids. For the purpose of this investigation, the set of fluids2 having ze = 0.27 was chosen because it in-cludes most of the heavier hydrocarbons usually found in those complex mixtures loosely defined as "reservoir oils". Data on undersaturated liquids in Ref. 2 were rearranged to conform with Eq. 8. To simplify the computation of cr, the isothermal p, data were plotted vs the log of pr, in which case for any straight line or tangent cr = 1/M pr pr .....(9)

Jan 1, 1958

By S. C. Sun

With the aid of emulsifiers, intense high-frequency sound waves are capable of emulsifying any collector in water. The data show also that ultrasonically emulsified collectors are more effective in floating minerals than the nonemulsified collectors. THE use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and OstrawskyV escribed the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanaka3 employed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets In the other. The dispersed liquld is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses, 5a, B proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft 7, 8 deduced that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids. This film has two interfacial tensions, one with the water and the other with the oil, which are not necessarily equal. The difference in interfacial tension between the two surfaces of the film is chiefly responsible for forming different types of emulsions. For example, if the interfacial tension between water and film is less than that between oil and film, the film will become convex on the water side, thereby tending to form an oil-in-water emulsion. On the other hand, if the interfacial tension between water and film is greater than that between oil and film, the film will become concave on the water side, thereby tending to make a water-in-oil emulsion. In line with this theory, emulsifying agents soluble in water have the tendency to form oil-in-water emulsions, while those soluble in oil form emulsions of the reverse type. Apparatus and Experimental Procedure: The ultrasonic apparatus shown in Fig. 1 consisted of a hypersonic generator (A), Brush Development Co. model Bu-204; a hypersonic transducer bowl (B) whose resonant frequency is 400 kc per sec; and a round-bottomed glass tube (C) of 2.2 cm ID and 21 cm in length. The acoustical output power of the hypersonic transducer bowl was standardized with a Hewlett Packard vacuum tube voltmeter, model 41 0B, across the hypersonic generator output. The glass tube, containing the materials to be emulsified, was placed 1 cm above the central surface of the transducer bowl, which was filled with water as shown in Fig. 2. Ultrasonic emulsification was performed in three steps, although a one-step method has been used: 1) emulsifying the predetermined amounts of col-

Jan 1, 1956

By R. E. Maringer, B. A. Wilcox, A. H. Clauer, J. H. Sovik

Internal friction measurements from 25° to 1100°C have been made on specimens machined from TD nickel bar. The use of miniature torsional pendulum specimens alloived damping measurements to be made on specimens whose axes were parallel to the original bar axis, at 45 deg to the bar axis, and at 90 deg to the bar axis. There was a marked difference in damping with varying specimen orientation, and this was related to the pronounced micro structural anisotropy of this material. Varying the microstructure by cold working plus re crystallization annealing also greatly affected the damping behavior. Recrystallization essentially removed the broad peak found at 400° to 650°C in as-received TD nickel, and in addition greatly lowered the background damping. DlSPERSION hardened metals such as SAP-type alloys (Al + AI2O3) and TD nickel (Ni + 2 pet ThO2) have been developed primarily to improve high temperature strength properties. There have been numerous damping studies on SAP-type alloys,1"9 and one of these6 showed that the damping capacity was greater than that of 99.5 pet pure Al from 25° to 600°C. Several preliminary observations on TD nickel10 and an experimental Ni-ThO2 alloy11 indicated that here, too, the damping capacity was quite high. A high damping capacity in TD nickel, combined with its relatively good high temperature creep strength, could provide an additional benefit for some high temperature structural applications. This work was undertaken to study the internal friction behavior of TD nickel bar over the temperature range 25° to 1100°C. In Ni-ThO2 and Ni-Cr-ThOz alloys, other properties such as steady-state creep rate,12 creep rupture life,12'13 modulus of elasticity,14 and ultimate tensile strength,14 are sensitive to orientation with respect to the primary working direction. Thus, in order to examine anisotropy effects in damping, studies were made on specimens machined with their axes parallel, at 45 deg, and transverse to the original bar axis. MATERIAL DESCRIPTION AND EXPERIMENTAL PROCEDURES The material used in this investigation was from the same £ in. diam TD nickel bar that has been studied previously.13'15 The structure typical of the as-received TD nickel is shown in Fig. 1, and additional details of the structure can be found in Refs. 13 and 15. Elongated grains are parallel to the bar axis and are about 10 to 15 u long and about 1 u in diam. This structure is very stable, since no recrys-tallization or grain growth occurred after annealing for 3 hr at 1300°C.13 The total ThO2 content was 2.3 vol pct and the particles ranged in diameter from 100 to 1000. The average particle diameter was 370Å and the mean planar center-to-center particle spacing was 2340Å. To examine the influence of grain and subgrain structure on damping, a section of TD nickel bar was swaged and drawn at room temperature from 1/2 in. diam bar to 0.040 in. diam wire (99.3 pct re-duction in area). The structure in Fig. 2 resulted after the wire was annealed for 3 hr at 1250°C. The recrystallized grains were much larger than the grains in as-received bar, but still showed considerable elongation in the direction of working. A high

Jan 1, 1970

By D. F. Stoneburner

The thermoelectric power and electrical conductivity of a series of liquid alloys of thallium were determined in order to study the relation of chemical bonding to semiconduction in liquids. The results indicate metallic behavior for the alloys of thallium with arsenic, antimony, and bismuth, while the sulfides, selenides, and tellurides indicate semiconduction. The results are compared with the Properties of the same alloys in the solid state. This work supports the observation that long-range order is not a necessary requirement for semiconduction. PREVIOUS work1,5 has shown that some sulfides and oxides behave as semiconductors in the liquid state. Although the band theory has been of great help in understanding the properties of solid semiconductors, its quantitative application to liquids is difficult. The very existence of liquid electronic semiconductors shows that ascribing the discrete structure of the energy spectrum to strict lattice periodicity, or long-range order, is not always satisfactory. Rather, the short-range order determines the structure of energy levels and the width of the forbidden gap and, consequently, the concentration of free holes and electrons. This is borne out by the analysis of data accumulated by Regel and coworkers.6 The similarity of electronic structure of liquid and solid phases of certain liquid metals was pointed out by Knight et a1.,7 who examined nuclear resonance in solid and liquid Li, Na, Rb, Cs, Mg, Al, Ga, Sn, and Bi. They found noticeable changes in the electronic structure upon melting only in the cases of bismuth and gallium. They concluded that "a liquid metal possesses a band structure which is very like that of the solid, provided the short-range structure is not altered during melting." In semiconductors in which the near-neighbor arrangement remains the same on fusion, the material would be expected to retain its semiconducting properties. The quantum theory of semiconductors, with its band structure of energy levels, is linked exclusively to long-range order. Furthermore, it has limited usefulness in predicting new semiconductors. Many sulfide8-12 have made comparisons of properties on the basis of crystal structure or the position in the periodic table, both methods involving the same factors as chemical bonding. Mooser and Pearson8"10 have pointed out that crystal structure depends on chemical bonding, and that this bonding is a property of the atoms themselves. As the periodic arrangement of the atoms offers an easy comparison of such factors as atomic weight and number of valence electrons it provides clues to expected similarities of bonding for various elements or groups of elements. This approach has led Mooser and Pearson to formulate their valence-bond theory of semiconduction, in which they define a semiconducting bond. These authors state that "semiconductivity is the result of the presence in a solid of predominantly covalent bonds. These lead, through the process of electron sharing, to completely filled s and p orbi-tals in the valence shells of all atoms of elemental semiconductors while in semiconducting compounds only one atom of any two bonded together need acquire closed s and p orbitals. The presence of empty 'metallic' orbitals in some atoms of a compound does not destroy the semiconductivity provided that these atoms are not bonded together; it may, however, give rise to pivoting resonance in

Jan 1, 1965

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By W. O. Philbrook, K. Natesan

A mathematical model was derived for the temperature change in a particle undergoing heterogeneous chemical reaction and heal exchange with a stream of fluid. The model has been applied specifically to the exothermic oxidation of spherical particles of zinc sulfide. Very good agreement was obtained between the theoretical prediclion and experimental observation. It was found that at no stage of the reaction was the particle subjected to a state of thermal instability. In studies of gas-solid reactions, it is generally assumed that the gaseous and the solid phases are at the same temperature throughout the reaction period. This is not strictly true since most of the reactions are either exothermic or endothermic in nature. This paper deals only with heterogeneous gas-solid reactions of noncatalytic type. In the case of exothermic reactions (e.g., roasting of sulfides), there may result an increase in temperature of the particle due to the release of the heat of reaction, and this increase in temperature may enhance the reaction rate and thus cause further release of heat. Such a "spiralling" effect may lead to a thermally unstable situation within the particle. On the other hand, in the case of endothermic reactions (e.g., calcination of limestone), there may occur a decrease in temperature of the particle as the reaction proceeds, leading to a virtual "quenching" of the reaction front. A general discussion of autothermic processes with emphasis on properties and reactor design is given by Van Heerden. 1 Levesque and cubicciotti 2 observed self heating of the sample in the oxidation of thorium. Anous et al. 3 observed self cooling of the sample in their dehydration studies on chrome alum. Cannon and Denbigh, 4 and Ong et al.5 reported self heating of the sample in their studies of the kinetics of oxidation of zinc sulfide. A typical plot of heat generation and heat loss rates with reaction temperature is shown in Fig. 1.'14 The Sigmoid curve represents the heat generation rate while the straight lines represent the heat loss rate. The main objectives of this analysis are to estimate the temperature increase of a single particle undergoing an exothermic reaction and to study the possibility of a thermally unstable situation within the particle. Also, a study of the dependence of the tempera- ture increase on different process variables has been attempted. A "she ll-by-shell" method has been proposed to analyze the problem. The shells may be made as small as necessary, and equations may be set up for heat transfer by various mechanisms. Such equations will have to be solved for each shell, with the boundary conditions for ith shell being obtained from the (i - 1)th shell, using a high speed digital computer. The oxidation of spherical particles of zinc sulfide is considered for this analysis, but the treatment is general enough to be applicable to other reactions and particle shapes. The oxidation reaction can be written as AH =« -115 kcal/mole ZnS [1] Such a reaction has been found to proceed in a topo-chemical manner; i.e., as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,4-6 that the particle retains its original dimensions. Therefore, at any given time, the particle may be

Jan 1, 1970

By G. R. Fitterer

Trends in slag composition in acid open hearth practice, particularly the variation in iron and manganese oxides during refining, are reviewed. A procedure which is currently being used to control the refining reactions is described and partially explained through slag phase diagram considerations. In addition, the ionic nature of these slags is considered and it is proposed that silica combines with the oxide ion and forms a series of complex silicate ions. The effect of basic oxides such as FeO, MnO, and CaO is apparently additive in furnishing the oxide ion for this purpose. IT is now possible to control192 the refining of steel in an acid open hearth furnace to a surprising degree. This control has been brought about through the knowledge and use of several facts and tests. These are: 1—A planned charge analysis based on a knowledge of the type of fuel, the bath depth, etc. 2—Knowledge and control of rate of fuel input as well as its method of atomization, if any. 3—Determination of the slag fluidity. 4—Bath temperatures (use of the Pt-Pt-Rh thermocouple). 5—Periodic determination of carbon content (use of the Carb-analyzer or Carbometer). Through the use of these control methods, a heat may be made to "melt-in" with or without residual manganese and silicon. The rate of refining or carbon elimination may be controlled accurately, and the desired tapping (or "go-ahead") carbon may be approached at a rapid or slow rate according to preference and type of steel being made. Thus operating time may be predetermined and greatly reduced. Further, all of the refining can be done without any ore or other oxidizing additions, and the heat may be brought to the desired tapping temperature simultaneously with the attainment of the desired carbon analysis. This control procedure is being used in most acid plants in the United States today and has been de- scribed.', ' Although the slag metal relations are sufficiently well known to control the heat as stated, yet it is possible to account for only about two-thirds' of the 0, which must have been used for the elimination of the carbon and other metalloids. Phase diagram studies' of the slags, slag weights, the metal particle theory,' ore additions, limestone additions, etc., may all be taken into consideration; yet, the mechanism of oxidation and source of all the oxygen remain to be explained. This paper reviews some of the principles upon which the control methods were based and proposes other possibilities regarding the unexplained phenomena. Old and New Acid Open Hearth Practice Some of the recent statements in the literature regarding acid open hearth operation are based on old heat data which are not typical of modern American practice. These old heat logs have been responsible for many misconceptions regarding the acid hearth practice and represent heats which do not coincide with modern methods. In recent years, American practice has been altered materially and these changes will be briefly described. Modern American Practice: A typical log of a modern American acid open hearth heat' is shown in Fig. 1 which indicates that the refining time was only two hours, during which the carbon was eliminated rapidly and the bath temperature increased at a fast rate. The manganese and silicon contents of the metal were essentially eliminated and their oxides had become constituent parts of the slag at the "melt-down" period. During the course of the heat, the MnO content of the slag remained practi-

Jan 1, 1954

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well's drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well's limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well's cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well's drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By W. R. Foster, J. M. McMillen, A. S. Odeh

The complete equations of average linear momentum balance for a single-phase fluid in an incompreisible, homogeneous, porous medium are derived. The derivation begins with Euler's equation of motion for a continuum and uses an integral transform recently developed by Slattery. 7 For steady flow of a compressible, Newtonian fluid, the usual equations of motion result. For transient flow, the space-time description of the pressure is determined in the lowest approximation by the telegrapher's equation. From the analysis a new phenomenological coefficient results which connects the viscous traction to the deriv ative of the linear momentum density. The magnitude of this coefficient determines the velocity of sound through the pore structure in this approximation to the pressure field. INTRODUCTION The modification of Darcy's law of momentum balance for steady, single-phase flow through porous media has been discussed for many years. The first modification was suggested by Forcheimerl who added terms of higher order in the velocity. These can be expected to appear because the underlying microscopic equations of momentum balance are themselves nonlinear in the point velocity field. The Reynolds tensor pvv, which represents the convective flux of momentum density, appears in the momentum balance equation. Only in rectilinear flow (parallel stream lines) does the divergence of this tensor vanish. Since the steady flow stream lines in most porous media are not parallel, nonlinear dependence of the pressure gradient on the velocity should naturally appear. This nonlinearity has nothing to do with turbulence in the ordinary sense of random fluctuations in the pressure and velocity fields. It arises simply because the stream lines converge and diverge, even for steady flows. Klinkenberg2 demonstrated that the permeability coefficient in Darcy's law depends on the absolute pressure or, alternatively, on the density field. However, because he neglected inertial terms of the Forcheimer type, his correction coefficient could not be represented by a constant but tended toward a constant as the velocity decreased. Forcheimer's and Klinkenberg's modifications can be combined in a rigorous way to account for both inertia and slip during steady flow. This will be shown in a future paper. The transient change of pressure in porous media has been described by the diffusion equation.3 This form results from eliminating the velocity and density fields from a combination of the equations of motion in the form of Darcy's law, the continuity equation and an equation of state. Fatt4 suggested that the cause of deviations from the prediction of the diffusion equation for pressure transients lies not in the choice of Darcy's law as the equation of motion but on the existence of dead-end pores which might invalidate the averaged equation of continuity. On the other hand, Oroveanu and Pascal5 noted chat the time derivative of the momentum density must be included in the equations of motion since this measures the local rate of change of momentum density. Their differential equation for pressure is the telegrapher's equation (neglecting gravity). However, their form of this equation predicts that the speed of pressure propagation through the pore structure is the same as that through the bulk fluid. M. K. Hubbert6 attempted a derivation of Darcy's law by volume averaging the Navier-Stokes equations. Since these equations represent momentum balance at a point within an open set of points containing the fluid itself, Hubbert's volume averaging cannot lead to tenns involving transfer of momentum between the fluid and the walls of the pores. Once these viscous tractions are lost by choosing a control volume containing only fluid, they cannot

By R. A. Swalin, L. A. Neimark

The research work presented in this paper had initially a two-fold goal. First, further data concerning the low-temperature recovery of cold work was desired. Recovery phenomena have been extensively studied in face-centered-cubic metals but at the time of initiation of this research, no investigation concerning the low-temperature recovery in body-centered-cubic metals had been made. During the course of the investigation a paper by Martin on the recovery of point defects in molybdenum appeared.&apos; Comparison of our results on tungsten with Martin&apos;s results on molybdenum will be made. Secondly, knowledge concerning the influence of a particular type of impurity addition on the recovery kinetics was desired. It has been known for a long time that extremely small amounts of certain impurity additions exert a profound influence on the recrystallization behavior and the resulting microstructure of tungsten. Small amounts of potassium silicate and aluminum chloride added prior to the reduction of tungsten oxide to the metal have been found by Smithells to raise the recrystallization temperature markedly,2 and yield an ultimate microstructure in which grains several millimeters long are produced in fine wires of say 10 mil diam. If the impurities are added singly, ordinary secondary recrystallization results with none of the spectacular properties of the wire to which special additions were made. Swalin and Geisler3 and Rieck4 have studied the recrystallization behavior of such doped wire in some detail. The former workers found that small amounts of these impurities raised the recrystallization temperature over 400°C and electron microscopic examination revealed no obvious inclusions in the microstructures. In fact. chemical analysis showed that there was <0.001 pct K, <0.002 pct Al, trace of Si, and <0.0003 pct 0 in the wire studied. The possibility that the role of the special impurities is to keep the structure open by void formation and that submicroscopic porosity acts as the inhibiting agent has been discussed.2&apos;3 Meijering and Rieck5 have suggested that the impurities are strung out as second-phase particles in a direction parallel to the drawing direction. It was thought that a kinetic study of recovery could perhaps elucidate the role of the impurities to some extent. When a metal is deformed by cold work three basic types of defects are thought to be introduced into the crystal lattice, namely, interstitials, vacancies, and dislocations. Van Bueren6 has proposed that recovery of cold-worked metal is a four-stage process, each step being the result of the annealing of a primary defect or a combination of defects and having a unique activation energy. The steps in order of increasing activation energy are attributed to a) the diffusion of interstitials recombining with vacancies, b) diffusion of vacancy pairs, c) the diffusion of single vacancies, and d) climb of dislocations. In metals with relatively low- or medium-range melting points the temperatures for recovery are low enough so that the first three steps may occur during room-temperature deformation. For tungsten, because of the high melting point and subsequently high recovery temperature, it was calculated, using Nowick&apos;s approach7 that this recovery would occur in the temperature range 200" to 600°C. It is also known that recovery of X-ray line broadening, presumably due to dislocation climb, occurs at about 600°C.8 EXPERIMENTAL METHOD Two types of cold-rolled 10-mil-diam tungsten wire were used in the investigation; a) pure tungsten, (called undoped) and b) G. E. No. 218 wire (called

Jan 1, 1961

By R. L. Hadley, G. Derge

The amounts of oxygen in liquid iron-titanium alloys up to 50 pct Ti were measured and the oxide phases in equilibrium with these alloys were determined by using TiO² crucibles. A minimum of about 0.003 pct 0 occurs at less than 1 pct Ti. The various liquid and solid oxide phases can be arranged on a ternary isotherm. THREE characteristics of titanium contribute to the interesting aspects of its reaction with oxygen in liquid iron: 1—It forms a number of stable oxides. 2—All oxides have large negative free energies of formation. 3—The pure metal exhibits high solubility for oxygen. In addition, the use of titanium as a stabilizing and strengthening element in alloys suggests a need for investigation of its reactions in amounts greater than those normally required for deoxidation. These higher compositions are also of interest because they occur during the addition of ferroalloys and produce deoxidation products before dilution is achieved. Titanium Deoxidation in the Literature While the use of titanium as an alloying element and deoxidizer has been common for several decades, the first detailed study of its deoxidizing characteristics was carried out by Wentrup and Hieber&apos; in 1939. These authors determined the extent of deoxidation possible with titanium and identified, by microscopic examination, the products formed. They found that titanium in excess of 0.2 pct did not reduce the oxygen content of iron below 0.004 pct at 1600°C. They identified the spinel FeO-TiO² at low titanium concentrations and Ti2O³ in melts containing more than 0.2 pct Ti. A portion of the area surveyed by Wentrup and Hieber has been investigated recently by Evans and Sloman² using X-ray diffraction for inclusion identification. They concurred in general with the findings of Wentrup and Hieber, but reported the existence of Ti³O5 as a deoxidation product in the range near 0.1 pct Ti. Comstock, Urban, and Cohen³ discussed the deoxidation of iron with titanium, correlating the data of Wentrup and Hieber with free-energy data for the titanium oxides. Scatter at high titanium values was considered attributable either to the formation of an oxide exhibiting high solubility in liquid iron or to the entrainment of solid oxide particles leading to high apparent solubility. Chipman&apos; has calculated the deoxidation curves for titanium based on free-energy data for titanium oxides. These calculations (Fig. 1) and those of Comstock, Urban, and Cohen involve assumptions as to the activity coefficients of oxygen and titanium in liquid iron, since such data have not been determined. Investigation of the deoxidizing characteristics of chromium" and vanadium0 have shown that these elements decrease the activity coefficient of oxygen in liquid iron, leading to a tendency toward relatively high oxygen values and experimental scatter in highly alloyed melts. Experimental This investigation involved two major objectives: 1—determination of the composition of the oxide phases in equilibrium with liquid Fe-Ti alloys, and 2—establishing the pattern of oxygen solubility in liquid Fe-Ti alloys at titanium concentrations in excess of that required for attainment of minimum oxygen content. Raw Materials Ingot iron was used having the following composition: 0.02 pct C, 0.017 pct Mn, 0.01 pct Si, 0.02 pct S, 0.006 pct P, and 0.03 pct 0. The titanium used

Jan 1, 1956

By H. R. Brannon, F. M. Perkins, Weldon O. Winsauer

Both the abnormal resistivity exhibited by shaly reservoir materials and their potential are due to adsorption of ions. Interrelationships between the two have been derived and verified by laboratory results. These relations which have resulted from this work may be used in a qualitative manner to estimate whether or not a particular shaly reservoir contains hydrocarbons, and also to estimate the porosity of shaly sands. INTRODUCTION In spite of the progress which has been made in the last decade toward a better understanding and utilization of the electric log, there remain a number of problems in the interpretation of the log. One of these which is often troublesome is that of divining the nature of the fluids in sandstones or carbonate rocks which contain appreciable amounts of shale. It was shown by Patnode and Wylliel in 1949 that shaly rocks exhibit an abnormally low resistivity when saturated with solutions of low ionic concentrations. This phenomenon has been demonstrated to be due to the adsorptive properties of shale or clay in the rock.&apos; In estimating the fluid content of shaly sands or carbonates from the electric log, it is desirable and sometimes necessary to correct for the abnormally low resistivity. A similar correction is likewise often necessary if attempts are made to estimate the porosity of a stratum from resistivity measurements. The correction may be made from data obtained on core samples and from information on salinity of interstitial water. Cores, however, are not always available. Moreover, even if cores are at hand, their examination is time-consuming. It would be most desirable, therefore, to make corrections of this nature from the log itself. Since both the abnormal resistivity and the potential&apos; are consequences of the adsorption of ions on shale, it should be possible to utilize the potential curve to give better interpretation of resistivity data obtained in logging shaly materials. The work described in following sections was directed toward this end. THEORY Relation of Resistivity of Shaly Reservoir Rock to Adsorpttve Properties In discussing the effect which the presence of shale or clay exerts on the resistivity of a reservoir rock, it is convenient to make use of the resistivity factor.4,5 This quantity has been defined as the ratio of the resistivity of the rock when it is completely saturated with an electrolyte to the resistivity of the electrolyte itself. When the rock, such as a clean sand or carbonate, is free of shale the resistivity factor is virtually independent of the ionic concentration of the electrolyte used to saturate the sample, so that F = R0/Rw = constant for a clean rock . . (1) where F is the resistivity factor, R0 is the resistivity of the rock saturated with electrolyte, and Rw is the resistivity of the electrolyte. When the rock contains argillaceous material, the resistivity factor as defined above is no longer independent of the concentration of the electrolyte used to saturate the rock, but decreases as the ionic concentration of the electrolyte decreases. In explanation of this behavior, it is instructive to consider a sample of shaly porous rock placed in contact with a large volume of a dilute electrolyte. The sample is considered to become saturated with the electrolyte, and to attain equilibrium with it. As a result of adsorption by the shale surfaces within the rock, there is a greater concentration of ions in the solution adjacent to the shale particles in the interstices of the sample than there is in the external solution with which the

Jan 1, 1955