Search Documents

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By D. C. Hilty, W. Crafts

L. S. Darken—Laboratory investigation of deoxidizing and other steelmaking reactions is usually centered, at least first, on the determination of the equilibrium or equilibria involved. This seems a reasonable procedure since equilibrium, if attained, depends only on composition, temperature, and pressure; hence conclusions derived from data on small experimental quantities are applicable to a heat of steel providing eauilibrium is attained in both cases. A knowledge of equilibrium serves as a useful framework even though we may know that practical conditions do not correspond to complete equilibrium. On the other hand, nonequilibrium or rate phenomena depend on a wider variety of conditions and are more difficult to interpret; conclusions applicable to laboratory conditions may or may not apply to larger scale phenomena. Hence the attainment or nonattainment of true equilibrium in the experiments here reported is of critical importance in evaluating their significance. Since some of the statements in this paper and in the closely related preceding one (on aluminum deoxidation) imply some doubt on this matter, I should first like to ask the authors whether their conditions are intended and believed to represent equilibrium. I should like to point out three considerations which seem to cast considerable doubt on the achievement of equilibrium, at least of the particular equilibrium under consideration. 1. In the experiments on manganese deoxidation the authors point out that they could not maintain the manganese-oxide slag on top of the metal in their rotating crucible, and hence they substantially dispensed with this slag. This leads to serious trouble in the interpretation of the results, for any equilibrium is, of course, a particular specific equilibrium—in this case Mn + O = MnO The experimental deletion of the upper layer of manganese oxide means that if equilibrium is attained at all it is attained between the metal and the MnO which has soaked into or adhered to the crucible (under the metal) and has dissolved substantial amounts of the crucible material including impurities. These impurities may constitute a significant portion of the slag by virtue of the small total amount of slag, even though the crucible is relatively pure. Hence there would seem to be a strong presumption that the equilibrium (if attained) involves not a pure MnO (or MnO — FeO) slag but one saturated with alumina and containing perhaps considerable impurities which substantially lower the concentration and activity of MnO, causing the above reaction to proceed to the right further than it would in the absence of alumina and impurities. Hence it is not surprising that manganese here appears as a better deoxidizer than found by other investigators. The present results may represent equilibrium with a slag of unknown composition which seems unlikely to be particularly related to plant experience. 2. The curves representing the observed silicon deoxidation (figs. 3, 4, and 5) are all drawn with a discontinuity in slope at about 0.02 pct oxygen. This point is interpreted as corresponding to the three-phase equilibrium, metal, slag, solid silica. The type of construction shown in these figures (though apparently fitting the data) is contrary to a fundamental principle of heterogeneous equilibrium as pertains to the construction of phase diagrams. According to this principle, the two solubility curves (each of the two portions of the curves in figs. 3, 4, and 5) must intersect in such manner that their (metastable) extensions must lie outside the homogeneous field rather than inside as in these figures. In other words, the "point" in these curves should be aimed in the opposite direction, if it is to be interpreted as corresponding to the three-phase equilibrium. The construction adopted is in violation of the second law of thermodynamics. This matter is discussed in detail in several texts and also by Lipson and Wilson.&apos;" The same criticism applies to the later figures representing conditions for manganese additions. The occurrence of this discontinuity or break at 0.02 pct oxygen casts further doubt on its interpretation. The earlier investigation of this system by Korber and Oelsen is in substantial agreement with the several recent findings of Chipman and coworkers that the oxygen content of iron in equilibrium with silica and silica-saturated iron oxide slag is about one third to one half that (0.24 pct at 1600") of iron saturated with pure iron oxide; thus there seems reliable evidence that iron saturated with silica and iron silicate slag at 1600" contains about 0.1 pct oxygen, or certainly much more than the 0.02 pct proposed in this paper. 3. In the quarternary system iron-silicon-manganese-oxygen one of the equilibria involved may be written 2 Mn + SiO2 (solid) = 2 MnO <slag> + Si The activity of SiO, is constant (if equilibrium is attained) by virtue of its presence as a substantially pure solid. At not too low metallic manganese content, the activity of MnO in the slag is constant by virtue of the fact that the slag is substantially pure manganese silicate saturated with silica and hence of constant composition. Thus the equilibrium constant for the above reaction is asi/a2Mn. Barring unanticipated large changes in the activity coefficients, the equilibrium constant may be adequately approximated for the composition range covered as [% Si]/[% Mn]2. Thus a plot of log [% Mn] against log [% Si] would be expected to be linear with a slope of one half as found by Kijrber and Oelsen. In the present investigation the slope (shown in fig. 15) is found to be one. It is difficult to believe that this finding represents a correct equilibrium determination, since it is at odds both with prior experimental investigation and with. theory. In view of the above points it seems that, although this paper reports many interesting findings, there is room for considerable skepticism as to the attainment of equilibrium and as to the conclusions drawn. N. A. Gokcen—The authors consider that Si% x O2% product is constant. This product is a function of the asi X a0 activity of Si02. The true constant is -------------. If the asio2 slags of this investigation were always saturated with SiO2 then Si% X O2% product would be constant,

Jan 1, 1951

By Walter C. Lawson

THE primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in&apos; the Morenci open pit. GENERAL MINING OPERATIONS Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months&apos; period (Fig I). Broken ore and waste, is loaded., into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high:. They are blasted- with churn drill holes, and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). PREPARATION OF PANEL GRADE In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many ties broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1947

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral rutile. United States consumption of titanium dioxide in concentrates for these applications in 1982 was as follows: pigments, 630,000 st; titanium metal, 31,000 st; and welding rod coatings, 5,000 st. The only commercially important titanium ore minerals at the present time are ilmenite and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) stated that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlined the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during that time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, VA, and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, FL, for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for low-grade sands, led to a return of activities in this area. The large deposits near Tahawus, NY. were brought into production in 1942 by National Lead Co. (now NL Industries, Inc.), and by 1949 this company was the leading producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec. The large Trail Ridge sand deposit in Florida was discovered by E. I. du Pont de Nemours & Co., Inc. geologists in cooperation with the US

Jan 1, 1983

On the following pages are abstracts of papers published by the Institute during the year 1932 as Technical Publications, Preprints, in bound volumes and in Mining and Metallurgy. For abstracts of papers that appear in bound volumes in 1932 but that were published as Technical Publications in 1930 or 1931, see the Transactions for those years. Papers that appear in this volume are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 309. Volume numbers are given as listed on page 3 and in the paragraph at the beginning of the index, page 315. The abstracts are grouped as follows: Page Page Metal Mining.................... 265 ferrous Alloys)................. 279 Milling and Concentration......... 268 Coal Division.................... 287 Iron and Steel Division............ 270 Petroleum Division............... 292 Nonferrous Metallurgy (Reduction Nonmetallic Minerals............. 299 of Ores)....................... 277 Mining Geology.................. 301 Rare Minerals and Metals......... 279 Mining Administration (Accounting, Institute of Metals Division (Found- Taxation, Industrial Relations). . 304 ing and Metallography of Non- Geophysical Prospecting........... 304 Metal Mining The Mineral Industry. By Scott Turner. (Min. & Met., June, 265. 3500 words.) Abstract of an address delivered before the Royal Canadian Institute, Toronto, April 16, briefly outlining the importance of mining in the United States, in Canada, and in the world. Comparison is made of the mineral production for 1886, 1900, 1910, 1920 and 1929, showing that in the 43 years from 1886 to 1929 that of the world increased nearly tenfold, of the United States over twelvefold and of Canada thirtyfold, but that Canada&apos;s output was equivalent to only 2 per cent of the world total and to 5 per cent of that of the United States in 1929. Statistical tables and graphs show value of production, percentage of world production contributed by Canada and the United States, etc. The mining situation in Canada is briefly reviewed: only those American engineers who have had occasion to examine the figures appreciate the rapidity of growth of Canadian mineral production. The treatment of minerals involves vast complex industries. When we are producing, say, 6 billion annually, the employment of 2 million workers provides indirect support to perhaps 10 million people. Exploiting mineral deposits is peculiar in certain ways, for the deposits are exhaustible, are of rare occurrence when measured in terms of outcrop area compared to total earth area, and may suddenly be handicapped or superseded by new discoveries; moreover, the economic position of the contained metals is &apos;affected by the use of scrap metal and the existence of invisible stocks. The largest and most valuable of the mineral deposits are not the metals, but rather the fuels. The record of the coal industry in recent years is one of brilliant technical achievement; its economic position is far from satisfactory. A so-called world fuel

Jan 1, 1932

By J. E. Burke

RECENT investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen, Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: [D=Ktn [11] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Walker4 finds that, in alpha brass, the rate of growth falls off more rapidly than indicated by Eq I after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker&apos;s data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: [t, Hr i &apos;_ III t„ = R \T, - ~) [2]] where t1 and t2 are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck.&apos; The results obtained by Beck, Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and Hu6 later demonstrated experimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,10 Making implicit use of this assumption, several authors14,15 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parker&apos; have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary, are on the average more surrounded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1948

By R. B. Hoy, Stanley J. LeFond, K. Reckling

Reported world production of natural diamonds approximates 40,000,000 carats a year (1980). The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, the Republic of South Africa third, and Botswana, fourth. Diamonds are also mined in South-West Africa (Namibia), Angola, Ghana, Sierra Leone, and other African countries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today it India, which was the first source of commercial production. In the US, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2,000 years ago, only about 260 tons have been mined. In order to obtain I g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential materials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamond in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (14/16 US mesh size). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite®, General Electric&apos;s Compax® and Stratapax® and Megadiamond&apos;s Megapax® have replaced natural diamond in turning tools, mining and oil drilling bits and dressing tool applications. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to modify light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem diamond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today.

Jan 1, 1983

By A. W. Dana, F. J. Shortsleeve, A. R. Troiano

The phenomenon of flake formation which may occur during cooling or room temperature aging of large steel sections is caused by a combination of hydrogen and stress. As such, the transformation characteristics of austenite in a particular section play a major role in the occurrence of flakes. Isothermal and continuous cooling studies demonstrated that flake formation is particularly sensitive to nature, distribution, and relative proportions of the microconstituents in the cooled sections. In the absence of transformation stresses, abnormally high hydrogen contents could be tolerated without flaking. Flakes were not found in the absence of transformation stresses. No correlation existed between average hydrogen content and flake formation where cooling stresses were low. Hydrogen in the steel was a necessary but not sufficient condition for flake formation. DESPITE a long history of laboratory and commercial investigations, the mechanics of hairline crack or flake formation in large steel sections remains unresolved. Recent publications1-5 emphasize that flaking is still a serious problem.* immediate cause of flaking is the pressure exerted by entrapped hydrogen gas that collects in small internal cavities or voids during cooling. When the temperature of steel is low enough to preclude extensive plastic flow, the cavity pressures cause local brittle fractures (flakes). 2—The microsegregation and transformation stress theory. According to this theory, flaking results from stresses arising from the volume changes accompanying the formation of martensite and/or low temperature bainite after a large portion of the section has transformed at elevated temperatures. The proponents of the hydrogen theory suggest that stresses from other sources may be additive to the stresses produced by hydrogen and may, in some cases, provide the increment of stress necessary to produce flakes. However, the critical aspect of this theory is that no stress, except that produced by hydrogen pressure, is believed to be sufficient in itself to produce flakes. For practical considerations, this means that the only safe thermal cycle is one that reduces the hydrogen content to some low critical level below which flaking will not occur regardless of the state of transformation. On the other hand, the transformation stress theory does not rule out the embrittling effect of hydrogen. This theory simply proposes that flaking does not occur in the absence of transformation stresses. With the transformation stress theory as a basis, commercial antiflaking cycles would be designed to complete the transformation of austenite prior to cooling to ambient temperatures. Both of these theories appear compatible with industrial experience. Antiflaking cycles, such as cooling at extremely conservative rates or soaking for periods of time in the upper subcritical temperature ranges prior to cooling to ambient temperatures, may allow the following: 1—diffusion of hydrogen out of the section and, as a consequence, reduction of the hydrogen content to some safe minimum value (hydrogen pressure theory) and 2—complete decomposition of the austenite at rela-

Jan 1, 1956

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months&apos; period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.&apos; A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By A. Raman

The Nb-Co system was nuestigated in the range 10 to SO at. pct Co with X-rays. A pt phase with the W6Fe.r-type structure occurs in the system between 46 and 52 at, pct Co. Its unit-cell dimensions are nearly identical to those of the p Phases found in the Nb-Fe and Nb-Ni systems. Two Laves phases, one having the MgZnz-type structure and the other the MgCuz-type structure, already t-eported in the literature, are found to exist in the system. The ,l.IgZnz-type phase occurs between 62 and 64 at. pct Co. A MgNi2-type Laves phase, reported in the literature, is no! obtained. A binalry phase is found to exist belozv I000C around 82 at. pct Co. THE cobalt-rich side of the system Nb-Co has been repeatedly investigated by previous inestiators" and the following intermediate phases are known to occur: NbCo, which crystallizes in the MgCu2-type structure and Nbc03,&apos; reported originally by Wall-bam, which has the MgNiz-type structre. Jordan and uwez&apos; as well as lliott&apos; were unable to find the MgNiz-type phase. Two phases, designated as x and y, were reported by Saito and eck.&apos; The phase x was inferred to have a narrow composition range near 77 at. pct Co. No published work is known to the author which reports the investigations in the niobium-rich portions of the system. This paper presents the results of an investigation in the Nb-Co system between 10 and 80 at. pct Co. EXPERIMENTAL PROCEDURE Two or three grams of the alloys under investigation were prepared using niobium (99.9 pct +) and cobalt (98.8 pct + with 0.14 pct Fe and and 0.03 pct C) in a tungsten-electrode arc furnace under commercial argon atmosphere. They were then wrapped in molybdenum sheets and annealed for a period between 5 days and 1 week at 1300°C in high vacuum (10-" orr) or in evacuated quartz amules for 2 weeks at 1000°C. Powders of -325 mesh size were prepared for X-ray work by crushing and grinding the specimens. Subsequent reannealing of the powders was not undertaken since most of the alloys were brittle and broke easily. X-ray powder patterns of the as-cast and annealed samples were prepared in a Siemens cylindrical camera (57.3 mm radius) with Cr-K, radiation. A Siemens diffrac to meter was used to get the X-ray patterns of some new phases. Metal log raphic examination of the alloys supplemented the X-ray findings. RESULTS The results of the X-ray and microstructural analysis Of the alloys are in in Table I. The lattice parameters of the phases are listed in Table 11 for quick reference. A set of micro photographs in Fig. l(n) to (j) show the microstructures of some alloys. A probable equilibrium diagram is drawn in Fig. 2

Jan 1, 1967

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By H. F. Silliman, Daniel R. Hull, John R. Freeman

In the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of cold-work and a considerable number of anneals. This condition has been disturbed by the preponderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2:r brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. Hot-rolled 2:1 Brass For illustration, therefore, a typical cake of hot-rolled 2:I brass has been chosen. This was rolled to a slab 36 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. I. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it would be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to 1706°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous days burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the day, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942