Search Documents

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

T. E. Leontis (The Dow Chemical Co., Midland, Mich.)—This paper is of particular interest to me because of my own work with F. N. Rhines on the oxidation of magnesium and magnesium alloys a few years ago. The authors are to be complimented on their development of an accurate and reproducible technique for measuring ignition temperatures and on their comprehensive study of the many variables that affect the ignition temperature of magnesium. It is indeed gratifying to see that they have obtained a good correlation between ignition temperatures and the oxidation rates reported by us. The correlation is valid not only with composition within one alloy system but also between alloy systems; that is, alloying elements which effect the greatest increase in oxidation rate also produce the greatest decrease in ignition temperature. There are a few points upon which I would like to comment. In attempting to correlate ignition-temperature data, one must be sure that the same definition of this quantity is used by all investigators. It does not appear to me that such is the case in the authors' comparison of their data with the theoretically calculated values of Eyring and Zwolinski. The equation derived by these investigators defines the ignition temperature, To, as the temperature at the gadoxide interface, whereas the present authors use the metal temperature as the criterion for ignition. The contradiction in the effect of oxide-scale thickness on ignition temperature between the predictions of the Eyring-Zwolinski equation and the observations reported in this paper indicate that some variable has not been taken into consideration. Could that be the geometry and size of the specimen? There is a marked difference in the type of specimen used in this investigation and that used in our work which formed the basis of Eyring and Zwol-inski's theoretical treatment. Another factor which plays an important role in ignition is the vapor pressure or the rate of vaporization. Combustion can safely be assumed to take place in the vapor phase by the reaction between vaporized magnesium and oxygen. Thus, a more accurate theoretical analysis may be made on the basis of the rate of vaporization which may be the controlling rate of the process. The effect of a large number of alloying elements on the ignition temperature has been reported in this paper, but beryllium was not included. Practical experience dictates that beryllium markedly decreases the burning tendency of magnesium. I was wondering if the authors plan to study the effect of beryllium in their future work. The authors predict that concentrations of sulphur dioxide in the furnace atmosphere greater than 5.8 pct would be expected to increase the ignition temperature to values still higher than those they measured. I would like to mention that large concentrations of sulphur dioxide markedly increase the rate of combustion of magnesium once ignition has started. Although it has been shown in the paper that the ignition temperature of magnesium in oxygen increases with increasing sulphur dioxide content up to about 1 to 2 pct, in practice relatively low-melting commercial cast alloys (AZ63A and AZ92A) are being continuously heat treated at temperatures just below the melting point in air containing 0.5 to 0.75 pct SO*. In regard to the change in color of the oxide scale observed on magnesium and magnesium alloys just prior to ignition, I would like to mention that in our work alloying elements were found to color the usually white magnesium oxide even though ignition did not occur. For example, the oxide formed on Mg-A1 alloys was gray, increasing in intensity with aluminum content in the alloy. Finally, I might suggest that the authors indicate their source of the value of 0.8 g per cc for the density of MgO as it is formed on magnesium upon oxidation at elevated temperatures. W. M. Fassell, Jr. (authors' reply)—The comments by Dr. Leontis are very excellent ones and I will attempt to answer them in order. First, the problem of ignition of magnesium is a rather difficult one since many factors are involved. Concerning the comparison of the To in the Eyring-Zwolinski equation, eq 4, with the experimentally determined values, it will be noted that the calculated and experimental values of the ignition temperature in Table I are not self-consistent. In the case of the 1.78 pct A1-Mg alloy the calculated value is 49°C below the experimental value; for the 3.81 pct A1-Mg alloy, 122°C below the experimental value; for Mg with 5x10-' cm film, 19°C above the experimental value; for Mg with 2x10-I cm film, 28 °C below the experimental value. Thus, if it were merely a matter of difference of location of temperature measurement the calculated ignition temperature would always be below the experimental value, the difference being due to the thermal gradient through the oxide film. The possibility of a thermal gradient in the magnesium metal must be considered. From Carslaw and Jaeger,'Y t can be shown that the maximum temperature gradient that could exist between the oxide-metal interface and the center of the sample is of the order of O.Ol°C. The geometry and size of the specimen could certainly have some effect on the ignition temperature. The equation for ignition that has been proposed in reference 14 is of the following type containing terms to account for this and other factors: M dT AHv(T) =Cp--------------\-J(.T—TB) + ZAHl-M A dx where AH is the heat of reaction, v(T) is the velocity of the reaction at temperature, Cp is the heat capacity of sample, M is the mass of sample, A is the area of sample, t is time, J is the total coefficient of heat transfer outward from the reaction zone, TR is the temperature of the bath or furnace, and AH,, is the heat associated with any phase change involved. Prior to the instant of ignition, the vapor pressure of magnesium is of no special significance. After ignition, neither eq 4 nor the above equation is applicable. The actual combination of magnesium cannot safely be assumed to take place in the vapor phase. While experimental data is lacking to support a hypothesis that ignition does or does not occur in the vapor phase, some observation on the pressure ignition experiments may be of interest. At high oxygen pressures, once ignition has occurred, the reaction of magnesium with oxygen approaches near explosive violence, the entire sample being consumed in probably less than 1 sec. At atmospheric pressure it usually requires 15 to 20 sec. Thus it appears that the oxygen concentration becomes the rate determining factor. Further, if burning magnesium is observed through darkened glass (Lincoln Super-visibility Shade No. 12) the magnesium sample is very much hotter than the "smoke" and the outline of the sample is retained perfectly. No "flame" is visible above the metal. No work was done on Mg-Be alloys. We do, however, intend to study this problem in the near future.

Jan 1, 1952

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By Lyman Taylor, Alexander R. Troiano

STUDIES of the transformation of austenite at constant subcritical temperatures have been numerous since the work of Davenport and Bain.1 Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of austenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. EXPERIMENTAL PROCEDURE Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8-in. round bars. Bars were softened at 650° to 700°C. before the specimens were cut. [ ] Metallographic Method Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examination of partially reacted specimens. Thees specimens were approximately ½ by ¼ by 1/8 in. in size. Specimens of the 9 per cent Cr steel were held 10 to 12 hr. at 1200° to I225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 ½ hr. at 1200°C. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. No. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed in Table I. X-ray Methods Constituents were identified and martensite axial ratios determined from Debye

Jan 1, 1945

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.' Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650' to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By H. A. Doerner

The process for smelting zinc developed several centuries ago is still in use. Through the experience accumulated over this long period of time, details of the process have been perfected until there is little opportunity to make any further improvement except by a radical change in method. Such a change was accomplished by the process recently developed by the New Jersey Zinc Co. The process to be herein discussed is a still more radical departure, which has been developed to large-scale laboratory operation by the Metallurgical Division of the U. 5. Bureau of Minesl. † The reduction of zinc oxide by carbon is a highly endothermic reaction, which requires temperatures in the range 1200° to 1400' C. for even a slow reaction rate. The transfer of the heat of reaction through thick fire-clay walls, the high radiation loss in the type of furnace used, and the practical impossibility of recovering or using the combustible products of the reduction (CO) cause a deplorable waste of fuel. With the one exception mentioned, all zinc smelting is done in small retorts manually charged and discharged. Attempts to mechanize these operations have been only partly successful, and there seems to be no way to avoid or improve the uncomfortable conditions in which the work is done. The reduction of zinc oxide by methane has a relatively high reaction rate at 1000' C. At this temperature most ore residues do not sinter, and it is possible to use metal retorts. These factors make gaseous reduction especially adapted to a continuous operation and compared to reduction by carbon make possible: (1) higher rate of reaction at lower temperature, (2) more nearly complete extraction of the zinc, and (3) much better utilization of fuel and reagent. Although the reaction between methane and zinc oxide requires 105,900 calories per mole, compared to 86,860 cal. in the carbon reduction, it is obvious that much less fuel will be required to supply 105,900 cal. through 36 in. of metal at 1000' C. than to transfer 86,860 cal. through 1 in. of fire clay at 1300° C. Moreover, the gaseous products of gaseous reduction (CO and H2) can supply 183,430 cal. by complete combustion.

Jan 1, 1937

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929

By H. D. Kynor

By the term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal and Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal and Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910" is as follows: Penna. Coal Co. D. L. & W.. ScRanton Temple Hudson YeaR and Hill- Tons Coal Co., Coal Co., Coal Co., Total, side Coal Tons Tons Tons Tons and Iron. Tons 1920................ 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919................ 950,786 no record 306,616 81,575 319,356 1,658,333 1918................ 917,778 744,966 24,880 44,756 288,781 2,021,161 1917................ 757,940 838,800 5,050 57,279 164,180 1,823,249 1916................ 286,780 860,663 13,960 114,173 101,475 1,377,051 1915................ 428,819 592,169 8,253 1,029,241 1914................ 219,188 153,896 373,084 1913................ 171,505 1912................ 124,267 124,267 1911................ 40,319 40,319 1910................ 1,184 1,184 a A slightly greater production was obtained than here indicated, as the tonnage from individual operations is not shown. b Decrease due to strike conditions in 1920. c Does not include tonnage of D., L., & W. d D., L., & W. decrease in 1920 due to having fewer mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 1, 1922

By A. H. Geisler, R. F. Mehl, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

By R. F. Mehl, A. H. Geisler, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

By Charles Fulton

EXPERIMENTAL work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such, a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc lead ores, since the residue from the distillation is held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet

Jan 9, 1919

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By A. M. Gaudin

The study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified: 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a substantially definite size which depends upon the ball size. 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with all the crushers tested. 7. Different methods of crushing produce grains of different shapes. 8. The importance of sizing the — 200-mesh portion of a crushed product, in crushing-efficiency investigations, has been greatly under-

Jan 1, 1926

By J. Sharshall Grasty, Thomas L. Watson

The users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the material in that region. The domestic production is derived from Missouri .and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral. General Character Barite, known commercially as barytes or heavy spar, is barium sulphate (Baso4), containing when pure BaO, 65.7 per cent., and S03, 34.3 per cent. The specific gravity is 4.3 to 4.6, and the hardness 2.5

Jan 1, 1915

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934