Search Documents

By E. W. Lithgow, E. G. Williams, R. R. Holbrook, B. R. Wilson

The mineralogy and geochemistry of Pennsylvanian shales and underclays were studied to determine their suitability for lightweight aggregate and refractory ladle brick. Eighty percent of the variation in bloating of shales and clays was explained by the variation of Si02, A1203, and fluxes (Fe203, MgO, CaO, Na20, and K20); 60% by variation in quartz, kaolinite, illite, and chlorite. The best bloating was exhibited by marine shales, whereas freshwater shales and underclays experienced little or no expansion. Regional paleogeographic maps o f Pottsville and Allegheny shales permit bloating to be geographically predicted. It was found that clays meeting the specifications for refractory ladle bricks were obtained from underclays having over 34.5% mica, over 40% kaolinite and less than 15% quartz. Underclays of this composition are confined to the lower Allegheney outcropping along the near-margins of the coal basin. The best clay is that underlying the Lower Kittanning coal. Porosity of the first fired brick was found to be inversely correlated with reheat expansion.

Jan 1, 1975

By R. E. Reed, R. D. Leggett, Paxton, H. W.

TECHNIQUES have been developed for growing monocrystals and bicrystals of Fe-20 Cr, Fe-20 Cr-20 Ni, and Fe-18 Cr-8 Ni alloys by both the strain-anneal and the Bridgeman techniques. None of the techniques are new but since they are simple and many people have expressed interest, they are described here quantitatively as they could be modified for other single-phase "commercial" materials of high melting point. CRYSTAL GROWTH BY STRAIN ANNEAL Flat tensile specimens with a tapered gage length were initially studied to deduce the approximate critical strain. Normal flat tensile specimens were then used. The optimum procedure for the austenitic steels (Fe-Cr-Ni) deduced from a variety of cold reductions, recrystallization treatments, tensile strain, and growth anneals was as follows: cold reduce 70 pct, recrystallize (after machining tensile specimens) at 1000°C for 1 hr, strain in tension 2.5 pct, and then heat to 1350°C as rapidly as possible. A time of 100 hr at 1350°C is usually sufficient to pro-

Jan 1, 1960

By R. A. Wyman

KYANITE schists in the Sudbury area have been generally described by Haw,' who has also given particuLar information on preliminary treatment of three large samples from Dryden township, Ontario.' Kyanite, garnet, biotite, quartz, and feldspar comprise the main ingredients of this ore. Kyanite is the valuable mineral. About 5½ tons of —35 +200 mesh product, made by dry rod milling, screening, and separation on the Exolon magnetic separator, were available for treatment by flotation. Magnetic separation had effectively reduced garnet and biotite so that flotation feed consisted essentially of kyanite, quartz, and feldspar, the kyanite content averaging 32 pct and representing about 86 pct of the kyanite in the original ore. Earlier work on kyanite at the Mines Branch, Ottawa, s-c employed an acid circuit, but to avoid production difficulties in the use of acids and at the same time take advantage of the fact that industrial minerals respond somewhat to soap flotation, it was decided first to investigate the higher pH levels. Exploratory tests using —65 +200 mesh feed ended with production of 96.6 pct kyanite concentrate rep-

Jan 1, 1959

By G. Sandoz

A simple diffusion-couple experiment was carried out for the purpose of determining whether chromium in sufficient amounts would cause the cementite phase in cast irons to become thermodynamically stable with respect to graphite and austenite at 1750°F. The implications of the results to some current theories on graphitization mechanisms are discussed. The literature abounds with evidence that chromium retards the decomposition of cementite to graphite and austenite or ferrite, for example during first-stage and second-stage graphitization in malleabilizing white cast irons and the subcritical graphitization of steels. Efforts to explain this retarding action of chromium have been conjectural, however, because the mechanisms controlling graphitization kinetics in the absence of chromium have never been clearly established. Concerning rate control, there are basically two schools of thought: 1) that graphitization rates are limited by diffusion potential (the stability of cementite relative to graphite, and 2) that graphitization rates are limited by diffusivity of Fe, C, Si, vacancies, and so forth.5'10 Chromium then, is thought either to increase the stability of cementite or to retard some critical diffusion process.

Jan 1, 1960

By P. D. Merica, A. N. Finn, R. G. Waltenberg

CeRtain compositions of the light, i.e., aluminum-rich, alloys of aluminum with magnesium and copper have become quite well known within the past ten years under the name of duralumin. These alloys are used for rolling and forging and can be so treated as to develop quite remarkable mechanical properties. Thus a properly heat-treated alloy containing about 4 per cent. of copper and about 0.5 per cent. of magnesium, rolled into sheet or rod, will have a tensile strength of approximately 55,000 1b. per sq. in. (3866 kg. per sq. cm.) with an elongation in 2 in. (50.8 mm.) of about 15 per cent. This alloy, duralumin, was developed by Wilm,1 and its properties more fully described by Cohn.2, The authors considered it worth while to investigate the mechanical possibilities of the light alloys of two somewhat analogous ternary series; namely, of aluminum-magnesium-nickel and aluminum-magnesium-manganese, to study the effect of variation of composition upon mechanical properties within the alumimum-rich group of the aluminum-magne-

Jan 1, 1921

By Marshall B. Standing, Donald L. Katz

DENSITY data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- [ ] carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. INTRODUCTION The densities of naturally occurring liquid hydrocarbon mixtures are important [ ] in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katz1 has indicated a method based on the principle of additive

Jan 1, 1941

By N. F. Dyson, T. R. Scott, M. R. Thornber, W. E. Ewers, M. Bussell

Leach liquors derived from the processing of nickel ores are generally highly contaminated and contain appreciable free acid. Methods are described for obtaining a commercial grade of concentrate from such solutions using pyrrhotite as the seed material to abstract nick- el, cobalt, etc. from solution. At temperatures in excess of 160° C., recoveries of 99% can be obtained from contaminated solutions where the free acidity is as high as 0.5 M in sulphuric acid. At lower temperatures down to 80° C., high recoveries can also be obtained either by adding H2S to the system with appropriate adjustment of the free acidity or by using "activated" pyrrhotite or artificial FeS in the system without prior addition of H2S. The methods are applicable to liquors derived from either oxide or sulphide ores, and the products are suitable for smelting or other known processes used to obtain pure metals. The mechanism of the reaction appears to vary with the operating temperature, and the results ye therefore discussed in the light of electron probe and optical microscopic studies.

Jan 1, 1973

By H. L. Ames, P. H. Jennings, R. W. Stanley

A process has been developed for leaching copper, lead and calcium from molybdenite concentrate. The leachant is a solution containing an oxidizing chloride (e. g., CuC12, FeC13) and an alkaline earth metal chloride (e. g., CaC12). Cupric chloride and ferric chloride, in the presence of 20-30% calcium chloride, are effective oxidants for chalcopyrite and galena. Calcium chloride, in addition to promoting the rate of leaching, serves to lower the solution pH and raise the boiling point. Leaching for two hours at 110'~ with a 1 % CuC12-10% FeC13- 30% CaC12 solution results in the extraction of up to 98% of the copper in molybdenite, 98% of the lead, and 79% of the calcium. Less than 0. 5% of the molybdenum is dissolved. The leach solution can be rapidly and effectively regenerated with gaseous chlorine and recycled. Build-up of copper and lead in the leach solution is controlled by discarding about 30% of the leach solution each cycle.

Jan 1, 1973

By T. D. Yensen, N. A. Ziegler

The elements aluminum,' arsenic,2 silicon,3 tin2 and vanadium,~.~ when used in relatively small amounts as alloying elements, seem to have a beneficial effect on the magnetic properties of iron—i. e., they increase the maximum permeability and decrease the coercive force—whereas there are definite indications that boron,5 carbon,6 nitrogen: oxygen," phosphorus16 sulfur6 and titaninum,~ as well as the metals of and adjacent to the ferromagnetic group, nickel,~ cobalt,1° copper," and manganese,% have a detrimental effect on these properties. The effects of calcium4 and magnesium4 are small, if any, while the effect of chromium12 in small amounts is unknown and in large amounts is generally detrimental. WeveR's Classification13 All chemical elements may be divided into three classes based on their effect on the allotropic transformation points of iron. Class 1 contains the nonmetallic elements (except phosphorus) and these lower the A3 point and raise the A4 point. Class 2 contains the common metals and

Jan 1, 1931

By R. S. Shoemaker, F. W. McQuiston

BENGUET EXPLORATION, Inc. Tuba, Benguet, Philippines 1970 Operating Data ORE DESCRIPTION: Complex ore mostly sulfides and composed mainly of sphalerite and pyrite with minor amounts of chalcopyrite, galena, arsenopyrite, hematite, magnetite, chlorite, calcite, garnet and quartz. TYPE OF MINE: Underground, cut and fill method ORE HAULAGE TO MILL: Mine rail cars with electric locomotives. CAPACITY in TONS/24 HRS: 130 ASSAYS: Mill Heads Mill Tails Au = 0.65 oz per ton Au = 0.096 oz per ton Cu = 0.75% CU = 0.27 % Zn = 10.50 % Zn = 0.64 % Ag = 3.20 oz per ton Ag = 0.33 oz per ton Cd = 0.01 % PRODUCT: Au, Ag, Cu, Zn and Cd RECOVERIES: = 90% ~g = 89% Cu = 60% Zn = 94% SCREEN ANALYSIS OF MILL FEED: 90% -200 mesh POWER: Grinding 25.4 Kwh/T Copper Flotation 14.5 Zinc Flotation 13.3 Cyanidation 20.4 Others 25.0 TOTAL POWER: 98.6 KwH/T WATER: Pumped from riverside and underground 50 to 100 meters distance. Consumption of about 700 gallons per ton of new water.

Jan 1, 1975

By P. D. Merica

Certain compositions of the light, i:e., aluminum-rich, alloys of aluminum with magnesium and copper have become quite well known within the past ten years under the name of duralumin. These alloys are used for rolling and forging and can be so treated as to develop quite remarkable mechanical properties. Thus a properly heat-treated alloy containing about 4 per cent. of copper and about 0.5 per cent. of magnesium, rolled into sheet or rod, will have a tensile strength of approximately 55,000 lb. per sq. in. (3866 kg. per sq. cm.) with an elongation in 2 in. (50.8 mm:) of about 15 per cent. This alloy, duralumin, was developed by Wilm,1 and its properties more fully described by Cohn.2 The authors considered it worth while to investigate the mechanical possibilities of the light alloys of two somewhat analogous ternary series; namely, of aluminum-magnesium-nickel and of aluminum-magnesium-manganese, to study the effect of variation of composition upon mechanical properties within the alumimum-rich group of the aluminum-magne-

Jan 7, 1919

By G. P. Hulst

THE Parkes process lead refinery of the International Lead Refining Co., at East Chicago, was built by the International Smelting & Refining Co. to treat the lead bullion produced by its Tooele plant, at Tooele, Utah. The plant was designed and constructed under the direction of the writer. Ground was broken Apr. 16, 1912, and exactly six months later the plant was in operation and lead was being cast. The capacity of the plant, running 25 days per month, is 5,000 tons. The four products of the plant are common lead, corroding lead, antimonial lead, and Doré bullion. The site is an area, 64 acres in extent, lying north of 151st Street, between McCook Avenue and the Canal. The Indiana Harbor Belt Railroad, Baltimore & Ohio Chicago Terminal, and Pennsylvania Railroad enter, the yard at the plant. There are five, storage tracks and space for storing 100 cars in the yard. The main lead to the storage tracks passes over a 100-ton track scale on entering the yard...

Jan 8, 1914

By H. R. Hanley

IN AS MUCH as the interesting changes in the economics of the zinc industry are covered nowhere else in this issue, and they are related to technological progress in the metallurgy of zinc, some reference to prices and production will first be made. The latter part of 1939 is outstanding in the large war demand for metals including zinc, whereas in the first eight months the demand for zinc was subnormal. The cause of the rapid in- crease in demand was the European war and hence the future is problematical. When the year began zinc was in the doldrums, with low prices, and continued thus until August when an advance in price started, reaching 6.5. per pound early in October. (Prime Western, St. Louis.) Rapid changes in the price of any metal are viewed adversely by the metal industry. The persistent low price for zinc of 4 to 49512 for about two years curtailed production and in one instance closed one large plant for a brief period.

Jan 1, 1940

IN the extra-mural service being built up by the Engineer-ing Societies Library as its finances permit, an occasional large total charge is incurred for exceptionally protracted services. A western steel company, for example; was charged the unusual fee of $500. They wanted complete informa-tion on transverse tests of steel, and asked the library to compile copies of all accessible records. Weeks -of search-ing and photoprinting produced three volumes of data. Two years afterward the company's chief engineer told the director of the library that the cost seemed high when the bill was paid but that the volumes had been in constant use. The information had been worth thousands of dollars. A client who wishes to pay no more than a moderate fee for services can state to what limit he is willing to go. Thus he may specify that he would like searches made on a particular subject but that he does not wish to exceed $5 or $30- for the information. The library is as willing to perform a small service as a large one.

Jan 3, 1928

By Strathmore R. B. Cooke, Iwao Iwasaki

RECENTLY spectrophotometry has been reported to provide a convenient technique for the rapid and reproducible determination of xanthate concentration in pulp solution 1,2 and for a kinetic study of xanthate decomposition in acid solutions." Since the application of this analytical technique is feasible for those compounds showing pronounced light absorption maxima in the near ultraviolet region, it was deemed advisable to investigate the absorption spectra of some of the organic compounds that are used in flotation. It is known empirically that certain groups of atoms in an organic compound cause characteristic light absorption in the ultraviolet and near ultraviolet range, and the wavelengths and intensities of the corresponding absorption maxima are relatively independent of the nature of the remainder of the compound. The characteristic values of such groups, which are known as chromophores, are given in the literature. 4,5 According to this information, many of the sulphydryl compounds are expected to show absorption maxima in the near or long wavelength ultraviolet region, whereas the saturated fatty acids and the saturated alkylamines do not.

Jan 11, 1957

By M. L. Fuller

THE fundamental mechanism of the deformation of zinc has been thoroughly described by several prominent investigators, particularly Mark, Polanyi, and Schmid,1 Mathewson and Phillips,2 and Schmid and Wasserman.3 The deformation of zinc occurs primarily through slip along basal planes {00. 1 }, and secondarily through twinning on pyramidal planes of the form { 10.2). In addition to these basic studies on single crystals, there have been a number of determinations4,5 of preferred orientations developed in rolled, polycrystalline zinc. In no case, to our knowledge, has there been described the development of oriented struc-tures in zinc as a result of a, systematic series of rolling treatments. The work included in the present paper shows the changes in orientation produced in a zinc alloy by successively increasing degrees of cold-rolling reduction. This alloy has the same crystal form, hexagonal close-packed, as zinc, but its susceptibility to hardening for a given degree of working is much greater because of its higher recrystal-lization temperature.

Jan 1, 1934

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By Karl Cohen

The question of attainment of competitive nuclear electric power is of interest to uranium producers because the rate of attainment of this goal determines the date when there will be a solid, non-political, domestic uranium market. It is a burning question to those of us in the civilian nuclear power business, because our entire business future hinges on how well, and how soon, we can make electricity from nuclear reactions at prices comparable to electricity from coal. For an idea of the magnitudes involved, consider that the first fuel load of the Dresden (Illinois) nuclear power station, plus spares, will be about 90 tons of 1.5 pct UO2. This requires about two-and- a-half times as much natural uranium oxide feed to the diffusion plant, or 225 tons. This, in turn, represents about a month's production from the nearby Uranium Reduction Co. mill. Note also that the 180,000 kw electric output of the Dresden station will be about 0.1 pct of the national electric generating capacity in 1960.

Jan 12, 1958

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969