Search Documents

By E. F. Bailey, W. J. Harris

THE temperature of the ferrite to austenite re-action is established frequently by continuous heating experiments. However, equilibrium studies of this reaction have demonstrated that austenite may form at temperatures considerably below those at which the reaction is first observed during continuous heating. Because of this discrepancy, tempering is sometimes performed above the true critical temperature and in these cases austenite forms during tempering. The lowest temperature at which austenite forms and the kinetics of the reaction have been studied by Bain,' Bleakney and Gros-venor,2 and Dube and Cunningham. This austenite can affect the properties either as austenite per se, if it is retained at room temperature, or as a decomposition product if it transforms. The effect of austenite formation during tempering on low temperature impact properties of an 8 1/2 pct nickel steel was reported by Brophy and Miller4 in work published after the present investigation was initiated. They concluded that the improvement in low-temperature notch toughness which followed tempering at certain temperatures could be attributed to the austenite formed during tempering. Kramer et al.5 found anomalous hardness increases and embrittlement after tempering of a low-carbon manganese-nickel steel. They concluded that austenite formed during tempering, and that the decomposition products were responsible for the increase in hardness and the embrittlement. Quan-titative correlations of the microconstituents and mechanical properties were not made by these investigators. The present study was undertaken in order to establish the kinetics of formation of austenite at various temperatures, the characteristics of the decomposition of this austenite, and the relationship between mechanical properties and the phases present. Experimental Procedure A low-carbon manganese-nickel steel was selected because of the sluggishness of its austenite decom-position reactions. The composition of this steel in percent was: C, 0.10; Mn, 3.52; Ni, 2.34; Mo, 0.52; Cr, 0.17; Si, 0.19; V, 0.15; P, 0.019; and S, 0.020. Samples were prepared by forging sections from a large ingot to 3/4 in. bars. Formation and decomposition of austenite were investigated by dilatometric techniques which were checked by X-ray measurements. Dilatometer specimens were hollow cylinders 1 in. long, 1/2 in. diam, with a 1/8 in. central hole. All specimens were aus-tenitized for 1 hr at 1650°F and quenched in water prior to insertion in the dilatometer. Oxidation was prevented by using an inert atmosphere of purified nitrogen. Dilation was measured with a dial gauge which could be read by interpolation to 0.00005 in. Temperature was maintained within ± 3°F by a Brown Electronik Controller. Chromel-alumel thermocouple leads were welded to opposite ends of the specimen with the specimen serving as the hot junction. As a check on temperature uniformity comparison was made of the specimen temperature as measured with the chromel-alumel leads and the temperature of the center of the specimen as measured with a calibrated platinum—platinum-rhodium thermocouple embedded in asbestos in the central hole of the specimen. During heating a 5°F temperature difference was noted below 1000°F, but none above, while in cooling, a 5°F difference was observed from 1300" to 735°F, but none below. Heating rates of 35°F per min and cooling rates of 60°F per min were employed for all dilatometric studies. For transformation studies below room temperature, the dilatometer was allowed to cool to 150°F and then was quenched into liquid nitrogen.

Jan 1, 1951

By P. Ramachandraraa, T. R. Anantharaman

THE technique developed by Duwez, Willens and Kle-ment' for rapid solidification of molten alloys in small quantities by ejecting them on to a highly conducting substrate with the aid of a shock wave has come to be known as "liquid quenching" or "splat cooling" in literature and has already been applied to alloys of many binary systems.' The very high cooling rates of the order of l060 to 1080 per sec obtained in this technique and the consequent drastic undercooling of the melt have led to such striking results as formation of new amorphous and crystalline metastable phases and extension of solid-solubility limits in many alloy systems. The cooling rates in these experiments can, however, be neither accurately measured nor effectively controlled and hence the occurrence of either more than one metastable phase or appreciable differences in constitution in splat-cooled alloys of the same composition cannot be ruled out.3 In fact, workers in two laboratories have reported formation of two different cubic metastable phases in liquid-quenched Au-Si alloys containing 17 to 20 at. pct si.4,5 The present note deals with some new and interesting results obtained in a Ag-21 at. pct Ge alloy and a Au-27 at. pct Ge alloy subjected to the liquid-quenching treatment at different cooling rates. Two alloys of nearly the same composition had earlier been rapidly solidified by the standard "gun technique" in the same laboratory and shown to solidify in nonequilibrium structures, viz., an hcp phase (a = 2.987Å;c =4.718Å) in the Ag-Ge system6,7 and both hcp (a = 2.885Å; c = 4.754Å) and tetragonal (a = 11.627A; c = 22.491Å) phases in the Au-Ge system.3 Apart from different substrates (copper and stainless steel), different melt temperatures (50º to 500°C above the liquidus), and different capillary sizes (0.4 to 1.5 mm diam) in the "gun technique", slower cooling rates of the order of l050C per sec were also obtained in the present work by replacing the substrate by water at room temperature in a modification of the technique due to Olsen and Hultgren.8 No attempt was made to measure the cooling rate in any experiment. The products varied from fine powder (>40 pct by wt—200 mesh) obtained by quenching in water to thin flakes and foils (11.0 sq mm to 4.0 sq cm) produced by splat cooling. They were subjected to the Debye-Scherrer method of X-ray examination in each case. In case of the Ag-Ge alloy, in addition to the expected metastable hcp phase,6 a coexistent tetragonal phase (a = 5.093,Å; c = 7.009Å) was detected in some experiments. Eight weak X-ray reflections from this phase could be identified, two of them being the same as reported earlier.7 With increase in the cooling rate, the dominant hcp phase seems to be first accompanied by traces of silver or germanium and then either homogeneous or mixed with traces of this new tetragonal phase. The splat-cooled Au-Ge alloy showed generally the expected hcp and tetragonal phases,3 but sometimes traces of germanium were also present. Further, two new tetragonal phases with the following lattice param ters could be clearly identified in samples quenched

Jan 1, 1970

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950

F. E. Thompson, Pottstown, Pa.: If Mr. Webster's endeavor to open up the subject of cast-iron should prove as prolific of results as did the discussion on " The Physics of Steel," he must certainly feel richly repaid. His remarks concerning the secretiveness and conservatism of the average foundry-man recall to my mind an instance of a blast-furnace which, for the last year, has been producing much foundry-iron. The manager, believing that much more of his product could be used in the foundry than the foundry-men were will-

Jan 1, 1896

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

By Cyril Stanley Smith

IsolatEd alloys of copper and silicon were prepared and examined by chemical methods more than one hundred years ago, but it was not until the work of Rudolfi l that the equilibrium relations were studied. The early history of the alloys was well described by Baradue-Muller 2 and need not be further discussed here. The diagram of Rudolfi, based entirely on thermal observations, showed sillcon to be soluble in copper up to 4.5 per cent. at 849" C., at which temperature there was a peritectic horizontal resulting from the formation of a ß phase with about 7.4 per cent. silicon from a and liquid with 7.85 per cent. silicon. The ß phase was believed to form a eutectic with Cu3Si at 820" C. and 9.8 per

Jan 1, 1929

By Frank Doxey

AT Dominion Steel & Coal Corp. it has long been recognized that continued mechanization of mine operations is necessary in the Pictou, Cumberland, and Sidney coal fields of Nova Scotia. The varied physical conditions in these fields call for special consideration of individual cases before planning is finalized. Because standard equipment cannot be procured which would operate successfully, many experiments have been necessary over the years to keep pace with the progress made in other countries. There are two mines, producing 2000 tpd, located in the Pictou coal field. The field is badly distorted and crossed by many faults. Seams are highly inclined and irregular and vary in thickness from 5 to 40 ft. Entries are difficult to maintain because of squeezing of the coal ribs and movement of the roof and pavement.

Jan 7, 1954

By M. L. Bleiberg, L. J. Jones

THE changes induced in metals by subjecting them to heavy particle bombardment have received widespread attention in recent years and results of such investigations have been reviewed by Slater, Dienes, Seitz, Siegel, and Seitz and Koehler.1-5 Of particular significance are the property changes that occur in uranium-base alloys due to neutron bombardment. These changes are generally very severe since fission occurs within the sample, resulting in the formation of heavy, highly energetic fission fragments, as well as additional neutrons born in fission, which serve to intensify the damage generally associated with fast neutron bombardment of nonfissionable metals. The property changes in uranium and uranium alloys due to neutron bombardment have been summarized by Paine and Kitte16 and Billington.7 It has also been shown that neutron bombardment of

Jan 1, 1959

By Ronald D. Hill, Janet L. Auerbach

It is estimated that the mining industry generates over 2.1 petrograms per year of solid waste. These wastes are overburden, waste rock, low grade ore, concentrate (tailing), sludges from treatment facilities and wastes from support facilities. Concentrate wastes present the greatest environmental problem. Three recent federal laws impact the disposal of waste from mining: Resource Conservation and Recovery Act of 1976 (RCRA), Surface Mining Control and Reclamation Act of 1977, and Uranium Mill Tailings Radiation Control Act of 1978. RCRA specified a special study on mining waste which was to include an analysis of: (1) sources and volumes of waste produced, (2) present disposal practices, (3) potential dangers to health and the environment, (4) alternate disposal methods, (5) cost of disposal, and (6) potential for use of waste.

Jan 1, 1980

By F. R. Hensel

THE alloy under discussion is a nickel-silicon bronze and is one of many age-hardening or precipitation-hardening FIG. I.-EFFECT OF QUENCHING AND AGING TEMPERATURES ON HARDNESS OF TWO TYPICAL NICKEL-SILICON BRONZES, NO. 2351 AND No. 2362. copper-base alloys. The hardening con-stituent is a nickel-silicon compound.1 The quenching temperature necessary to pro-duce hardening by a subsequent aging treatment is a function of the composition and extends from about 700'C. to ()50'C.; the aging temperature range extends from 400° to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Si; balance, copper.

Jan 1, 1940

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

By Leon Nelson

SEVERAL factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in. square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation.

Jan 1, 1937

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921

By Paul A. Bailly

Around 4500 B.C., the Pharaoh of Egypt ordered a military campaign to the Sinai Peninsula and the shores of the Red Sea, to search for copper deposits which Egypt needed for jewelry, vases and weapons.5 To my knowledge, this is the first recorded expedition aimed at the discovery of minerals. The diligent Egyptian soldier-prospectors made discoveries through visual detection and manual effort, the approach which has given us the bulk of our mines to date. In the Rio Tinto District of Spain where Roman miners followed the Phoenician traders, we find the first evidence of discovery of hidden ore bodies in the absence of mineralized outcrops. This is how Joralemon 13 describes these Roman discoveries to the southwest of the Rio Tinto hills, under the flat plain of Seville:

Jan 6, 1979

By Werner Joseph, Richard R. Knobler

When the first batch of refined copper ingots was cast at Mantos Blancos in January 1961, eight years of exploration, development and metallurgical pioneering by Mauricio Hochschild & Co. had come to a successful conclusion. This Chilean copper deposit, located in the Atacama Desert 30 miles from Antofagasta, is now producing approximately 20,000 tons of copper per year. The Mantos Blancos deposit has been known since 1912 and various attempts had been made to work the high-grade zones before the present operation was started. The major drawback of the ore to any previous development was its chloride content which varies between 0.4% and 1.5% C1. Although the chloride ruled out the conventional leaching-electrolysis scheme, it did lend itself to the process of precipitating the copper as cuprous chloride.

Jan 1, 1962

By Garth M. Crosby

Seven mines with important production records in the Coeur d'Alene lie adjacent to the Gem stocks -the Frisco (Gem), Hercules, Interstate, Rex (Sixteen to One), Success (Granite), Sunset, and Tamarack. Old records are incomplete, but avail- able data given in Table I show these mines have produced 10,550,721 tons of ore containing more than 50 million oz of silver, more than 1.5 billion lb of lead, and about 1 billion lb of zinc (approximately 1.25 million tons of lead and zinc combined). Average ore grade is 4.8 oz of silver per ton, 7.2 pct Pb, and 4.6 pct Zn. This impressive production represents about 12 pct of the District's yield. At present metal prices, with modern beneficiation, the gross value would be more than $400 million.

Jan 7, 1959

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

1. A passenger rickshaw in China. 2. A Pekin cart carrying coal, on dirt roads; the cost works out to 15 or 20 c. per ton-mile. 3. Coolie with wheelbarrow. This one has a small load, but barrow men carry ordinarily 250 lb., occasionally 400 if with a helper. He goes about 18 miles a day and the cost is about 25c. gold per ton-mile, though it varies widely. 4. Coolie delivering coal balls in Pekin. He carries about 65 lb. On some roads with a different arrangement a coolie carries 133 lb., making about one ton-kilometer per day. 5. Truck used by the Government Fuel Yard at Washington. Carries 71/2 tons in an hour as far as a barrow man carries 1/4 ton in a day.

Jan 8, 1928

By Randy M. Cole, Peter J. Phillips

A methodology is presented which quantifies six coal utilization cost components, each proportional to a coal's mineral content. These are: Ash disposal costs, coal transportation costs, plant maintenance costs, reduction in plant peaking capacity, reduction in plant rated capacity, and reduction in plant availability. Numerical examples illustrate that coal containing between. 12.5% and 25.0% ash-plus-sulfur can cause incremental utilization costs ranging from less than $1.00 to more than $8.00 per ton of coal, when combusted in a pulverized coal fired power plant. Estimated costs are then compared to historical data and the conclusion drawn that steam coal beneficiation may have broader economic justification than sometimes realized. It is noted that TVA, which first proposed the methodology and parameters used here, is continuing research on this aspect of coal utilization.

Jan 1, 1981

INTERNAL The year 1976 was another outstanding year in the operation of the Institute and in the success of its varied activities. Total AIME membership reached 59,773 for a gain of. 6.4 percent. Total revenue increased to $5,111,2 10, up 22.4 percent, and balance sheet assets increased to $8,479,612, up 12.2 percent from the previous year. AIME and its constituent units conducted 30 technical meetings during the year, and attendance was up at most of them. Publications issued by the Constituent Societies continued a healthy growth. During the year 9 new local Sections were established, and at the end of the year the Institute had 150 Sections, with 19 of them overseas. Details on all of these operations are on pages 2 and 3 of this report.

Jan 4, 1977