Search Documents

By T. M. Williams

DURING the year just ended we have had three great fires in the mines in the Wilkes-Barre district. One at the Empire Colliery, one at the Prospect shaft, and the other at the Baltimore old mine. It is proposed in this paper to give a brief history of the fire at the Empire Colliery, and the methods employed in extinguishing it. The fire was first discovered breaking out in the air-stack, alongside what is known as the " Kidder Plane," about one o'clock on the morning of December 31st, 1873. Subsequently it was ascertained that the fire originated in the return airway somewhere near the steam boiler, located inside the mine, near the head of No. 5 slope. The coal from this slope was hoisted to the shaft gangway, at a point nearly four thousand feet distant from the foot of the shaft. As there were from four to five hundred mine cars hoisted per day from this slope the steam boilers were located at this place. The mines being of considerable extent required a large volume of pure air for ventilation, and no fan having been erected at this slope at the time, the heat from the boiler was made use of to assist ventilation, by conveying the return air from No. 5 slope into the large airway made from these boilers to the surface through the old "Kidder slope" to the stack where the fire was first discovered. The length of this slope or airway was about one thousand feet, with a sectional area of about sixty feet. The quantity of air passing through it must have been over sixty thousand cubic feet per minute

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919

By T. R. Young, S. A. Scott

9.5-1. Introduction. The use of pipelines to transport solids has been successfully accomplished with many different materials. One of the oldest applications is the dredging and placing of hydraulic fill. Many installations have been made and operated for long periods of time with excellent dependability, low operating cost, and low maintenance. It is not the aim of this chapter to give the engineer the answers from which to design a pipeline, but rather to supply helpful information from which to start the project. There are several phases of solids pipelining which as yet have not lent themselves to quick engineering answers. Investigations have been carried on by many, with several theories advanced by the various investigators. In recent years certain notable theoretical advances in hydraulic transportation have been achieved. Vertical transport, using balanced "leg" operation, now appears competitive with other forms of vertical transportation. In addition, horizontal transport utilizing capsules has been proven experimentally to be attractive because of lower pressure drop than the conventional methods of solid transport in fluid media. With the aid of the computer, the laborious calculations associated with pumping calculations have been greatly simplified; and with this tool the pipeline engineers of the future will undoubtedly be able to develop a more comprehensive understanding of solids-fluid transport. 9.5-2. Theory. There have been many excellent studies made and information is available in the literature, but a general comprehensive theory of pipeline transportation of solids has not been advanced. The existing flow theories will give approximations for minimum and optimum flow velocities, friction head losses, energy requirements, and pump and pipe size The principles of dynamic similarity and scaling laws are well understood for the flow of pure liquids. There are no firm methods of scaling slurry pipelines of small diameter to larger diameters except for a few empirical.

Jan 1, 1968

Endurance Properties of Non-ferrous Metals Discussion of the paper of D. J. McADAM, JR., presented at the Syracuse Meeting of the Institute of Metals Division and issued, as Paper No. 1506-E, with Mining AND METALLURGY, October, 1925. H. F. MOORE,* Urbana, Ill. (written discussion).-This paper says that the results of tests of some non-ferrous metals made at the University of Illinois and in the testing laboratories at McCook Field are abnormal when they do not agree with results obtained by the author. The writer can see no inherent reason why results of the type uniformly reported in this paper are any more normal. The knee of the stress-cycle, or S-N, diagram comes at different lengths of life for different metals. For steel, the knee occurs after from 1,000,000 to about 4,000,000 cycles, and for some non-ferrous metals not before 20,000,000 of 30,000,000 cycles. The writer can see nothing inherently abnormal in finding certain nonferrous metals for which the knee of the stress-cycle curve occurs at 1,000,000,000 cycles or higher. The writer has had experience with both the cantilever and the rotating-beam testing machine, and thinks that the chance of whipping action in the cantilever machine is a more serious handicap than the action the author has pictured. Furthermore, the writer questions whether the author has shown the existence of a clearly marked and definite endurance limit for all the non-ferrous metals he has tested including the following: Nickel (CT and A-16, Fig. 1), monel (CS-5.5 and BK, Fig. 2), bronze (F and CK, Fig. 4), aluminum bronze ( BJb-1, Fig. 6).

Jan 12, 1925

George W. Maynard, New York, N. Y.:—It is well known that there are many magnetite-mines of which the ore is too low-grade for direct use in the blast-furnace. For carrying out the sintering process, the preliminary step, in the case of magnetites, is the separation of the ore from the gangue by magnetic concentration. The resulting fine-grain product is very objectionable in the blast-furnace, and when used must be a very small percentage of the charge. The sintering process has saved the situation by furnishing a product which is absolutely ideal on account of its cellular structure. (In reply to questions by W. J. Tudor, and Joseph W. Richards, the following additional information was given by Dr. Maynard.) The percentage of iron in the product is determined entirely by the degree of concentration of the raw material and is practically not increased by the sintering operation. The magnetic concentrates at Port Henry and at the Benson and one or two other mines contain from 65 to 67 per cent. of metallic iron. The cost of sintering is from 39 to 41 cents per ton of product, including superintendence, depreciation, and repairs. The itemized figures are about as follows : Mixing (including labor), 24; power, 9; ignition, 5; repairs, 3; total, 41 cents. Prof. J. W. Richards, South Bethlehem, Pa.:—From a metallurgical standpoint I question the accuracy of the statement on p. 374: " C.—An increased reducibility of the iron so treated. (This has been conservatively estimated as 5 per cent. better than the best available ore.)" It seems to me that when a material is' sintered in this way, the constituents present, as lime, silica, and alumina, have a chance to form a compound with the iron oxide; that such a compound, if formed before the material goes into the blast-

Jan 1, 1913

By E. W. Mehal, R. H. Cox

A planar Gunn oscillator was developed for use in a monolithic microwave integrated circuit. The device was designed to operate in the frequency range of 20 to 30 GHz with a continuous wave output. Selective epitaxial deposition was used to form the n+n-n+ device structure in (111)-B semi-insuluting GaAs. The active n- region was about 5 µ thick and was doped to about 2 x 1015 electrons per cu cm by the reactor background. The mobility was -5000 sq cm v-1 sec-1. The n+ epitaxial deposits were doped to 1 x 10" electrons per cu cm using S2Cl2. Planarity of the three DURING the past few years, new microwave devices in discrete form have been developed utilizing GaAs. The next logical step is to combine these devices in a successive deposits was quite good; total overgrowth was less than 1 µ. Metal ohmic contacts were applied to the n+ or n- regions using a Ag-In-Ge alloy. The n+n-n+ devices had symmetric IV characteristics and could be operated C. W. for both directions of device bias. Metal ohmic contacts made directly to the n-region always Produced asymmetric devices. C. W. operation was obtained over the 22 to 28 GHz frequency range. The best performance obtained was 1.5 mw C. LV. output at 28 GHz. microwave integrated circuit. A potential application would be a radar receiver operating in the millimeter wavelength region. The key component in such an integrated circuit is a microwave oscillator, recently described by Gunn.1, 2 Under the influence of a large electric field, high-resistivity GaAs exhibits a bulk negative resistance, and high-frequency current oscillations result. Since relatively high voltage and

Jan 1, 1969

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By V. B. Tare, H. Schmalzried

The use of solid electrolytes for determining kinetic paraneters at elevated tevnperatures is pointed out. The reaction rate constant k1 of the phase-boundary reaction during oxidution of iron to wiistite by CO2-CO gas mixtures has been deternined between 850 nnd 975C, using ZrOz(+CaO) as an electrolyte. Values are between 1.4 x 10-a and 5.2 x 10 ole per sq ctn atm. The tzain difficulty is due to mixed potentials arising from side reactions at the electrolyte inteyface. In a number of papers the calcium-doped zirconia electrolyte has been used for the determination of thermodynamic data from measured differences in oxygen activities (or potentials) between two electrodes. The purpose of this note is to suggest the use of this solid electrolyte for kinetic measurements as well. The principle can be seen from Fig. 1. A thin and compact phase II (electron conductor) is fixed on a plate of gas-tight, polished ZrO2(+CaO) (I), which separates two compartments with different oxygen potential. p, is a constant reference pressure of oxygen (1 atm). The electromotive force of this galvanic cell is given by E = RT5 In pep, and pe is the oxygen partial pressure at the interface electrolytephase 11. If phase I1 is in equilibrium with the surrounding gas phase, p, = DR. If pg changes sud- denly to a value pi, p, and therefore the electromotive force, E, change as a function of time according to the phase-boundary reaction rate at the gas phase I1 interface and the transport processes inside phase 11. It is assumed that local equilibrium is established at the boundary electrolytephase 11, that the gas phase shows no concentration gradients, and that the con-

Jan 1, 1967

By J. M. McCormack, R. K. Saxer, J. R. Myers

ThE Knudsen effusion technique was used to determine the chemical activities of copper and platinum in binary Cu-Pt alloys in the temperature range 1542" to 1673°K. Wiebke and Matthes1 previously obtained chemical activities of copper and platinum in this system at 673° and 923°K by the electromotive-force measurement method. They reported that the copper activities exhibited negative deviation from Raoult's law at all compositions. The chemical activities of platinum were found to change from a positive to a negative deviation at 923°K. Myles2 recently studied this system in the temperature range 1265° to 1356°K by means of the torsional-effusion technique. His results indicated that both copper and platinum exhibited negative deviation from ideality at all compositions. The use of the Knudsen effusion technique to obtain the vapor pressure of metals and alloys is well-known.3 In this work, Knudsen cells were fabricated from seamless tantalum tubing of 1-in. OD and 0.020-in. wall thickness; cell bases and covers were cut from 0.010-in.-thick tantalum sheet and welded to the cells in an argon atmosphere. Orifices were drilled and reamed to approximate a knife-edge of 30-deg included angle. Calculation based on Balson's4 derivation showed the orifice to be nearly ideal. All temperature measurements were made with a Leeds and Northrup disappearing-filament-type optical pyrometer at the orifice of the cell, which closely approximated black-body conditions and eliminated the need for emissivity corrections. Details of the experimental techniques used, and the necessary correction factors required during this investigation are essentially those previously described.5,6 Before investigating the Cu-Pt alloys, vapor-pressure measurements were obtained over specimens of pure (OFHC) copper. The pure-copper data5 served to assure the accuracy of the experimental apparatus and technique.

Jan 1, 1967

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By R. Taggart, J. W. Barton, G. R. Purdy, J. G. Parr

The constitution and mechanical properties of heat-treated alloys containing up to 10 pct* Ni in Ti have been investigated. The effects of quenching and of various isothermal treatments ale described, and C-curves are presented. The production of the precipitated and the martensitic hexagonal phases on quenching is discussed. MARGOLIN, Ence, and Nielsenl have determined the titanium-nickel phase diagram. A study of the transformations in gas-quenched and tempered powder specimens was made by Polonis and Parr.' Some isothermal transformation work was carried out by Margolin and ~unshah, who determined transformation curves for 4 and 6 wt pct alloys, while Robinson et al.investigated the formation of the w phase in a quenched and tempered alloy, Margolin and Bunshah showed that while a martensitic transformation could be obtained on quench- ing thin sections of a 4 wt pct alloy, a 6 wt pct alloy precipitated a nonmartensitic phase. The present investigation was undertaken to obtain more information on the transformations in quenched, quenched and tempered, and isothermally transformed lump specimens of alloys containing up to 10 pct Ni. Isothermal transformation curves have been determined for 7 and 10 pct alloys and cooling curves have been obtained for quenched alloys containing up to 7 pct Ni. The mechanical properties of 2, 5, and 10 pct alloys were studied, with the object of relating properties to microstructures. EXPERIMENTAL METHODS Alloys containing up to 10 pct Ni were prepared from sponge titanium and spectrographic standard nickel by levitation-melting and chill-casting in a split copper mold. The 5 and 10 pet alloys were prepared from sponge Ti having an as-melted hardness of 115 Vpn. The other alloys were made from a sec-

Jan 1, 1961

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By Donald N. Rosenblatt

I would like to commend the author on his description of Pinto Valley's plant, and its interesting innovations. The author's discussion of 18 ft in diameter by 21 ft long primary ball mills (the largest wet ball mills made to date) is of considerable importance to those who have been engaged in the field of studying ball mill liner wear as it relates to various grinding installations. While it is stated that the mills have operated on a fixed tonnage and therefore it has been difficult to determine the best liner pattern, calculations from the data in the paper indicates that for mills 1, 2, 5, and 6, the tonnage per hour varies from a low of 223 for mill No. 1, up to a high of 314, for mill No. 2, while mills 5 and 6 calculate 285 and 246, respectively. Analysis of the wear patterns for the single wave liners used in mill No. 1 as compared to the double wave liners in mill No. 2, suggests that the author's data may tell more than he suspects about liner wear to be expected and thus what should be a best pattern selection from what may appear to be only limited hours of operation. [Fig. A] is a reproduction of author's [Fig. 10], to which wear forecast patterns [F-1 and F-2] have been added. Forecasts are based on many previous studies of large diameter ball mill operations over many years of field service. Calculations from the first-wear pattern provide an initial wear rate of only 13 lb of liner per 100 sq ft of shell liner surface per day, or 0.031 lb per to: ground. However, the second wear pattern is ac-

Jan 1, 1978

By W. E. Thorne

The object of this graphic method is to estimate the weight of the casting, which is to be made from a given pattern, when the cross-section is not a uniform geometrical figure. Such an estimate is a very important guide to the foundryman, who would otherwise guess at the probable weight of a casting of new design, and, in trying to be on the safe side, would probably melt an unnecessary amount of iron. It is also an aid to the designer of a new car-wheel pattern, who must otherwise estimate from general experience the probable weight, have test-wheels made, and correct the pattern afterwards, so as to obtain the weight prescribed. For the method here described, an accurate drawing of the pattern is employed. This gives a closer result than a drawing of the wheel itself, for the following reasons: 1. Calculations based upon the actual dimensions of the wheel involve the erroneous assumption that the specific gravity of the casting is uniform throughout; and upon that basis the calculated weight would be wrong, because the amount of metal poured has shrunk in the mould, acquiring the highest density in the outside chilled portion, and growing less dense through the mottled to the gray portions. 2. Calculations based upon the dimensions of the pattern or " chiller " assume that the cooled metal will not have shrunk, but will have the volume of the pattern and a uniform density. These assumptions, though erroneous, counterbalance each other. For instance, the patterns and the chiller which give a wheel 33 in. in diameter when cold, are respectively 33.5 in. in diameter. This shows a shrinkage for wheel-iron of about & in. (ordinary gray pig is commonly assumed to shrink about 1/8 in.) per foot. Wheels cast in 33.5-in. chillers do not always have the

Jan 1, 1903

By William R. Rumbold

When I was in South Africa during the latter part of 1904, there were three known tin-fields, which may be called the Cape Town, the Bushveld, and the Swaziland fields. The Cape Town Tin-Field. This district is situated near Kuils river, 20 miles west of Cape Town, and 5 miles from Kuils River station on the Cape Town & Stellenbosch railway. The deposits are in granite, intrusive in the Malmesbury beds, which are supposed to be of Silurian or Cambrian age. The granite, resisting denudation better than the surrounding shales, has formed low-lying hills, the highest of which, the Bottlelary Berg, is 1,510 ft. above sea-level. The rock consists of quartz, orthoclase feldspar, and biotite mica; tourmaline is also present. The feldspar occurs in large crystals. The rock is generally decomposed on the surface, and the decomposition sometimes extends as deep as 100 ft. This formation—granite intrusive in Silurian shales— extends for many miles to the northeast, but so far as I know the Kuils River deposits are the only ones now known to occur in it, though probably further prospecting will reveal other deposits. This particular discovery was accidental; alluvial tin being found in the course of boring for oil. The Kuils River Deposit. This deposit comprises both lode and alluvial tin. The lode strikes N-S., and dips about 30' E. into the hill. It is 5 ft. wide, and composed of dense white quartz, in which pinkish-gray cassiterite is distributed in large crystals. The vein also contains considerable quantities of wolframite. Fig. 1 is a rough plan of the relative positions of the lode and the alluvial deposit, the latter, as shown, following the course of a stream, while the lode crops out on the hillside ,

Jan 1, 1909

By R. P. Marshall, L. P. Costas

The solid solubility of lithium in aluminum was determined by two independent techniques, electrical resistivity and microhardness, and the results are in close agreement. The solubility limits X-ray diffraction studies of the intermetallic compound LiAl indicate that its composition is nearly independent of temperature when in equilibrium with the terminal solid solution of aluminum. THE investigation of the aluminum-rich portion of the aluminum-lithium system at the Savannah River Laboratory was prompted by the observation that over-aged alloys consistently differed from the equilibrium states predicted by the latest published diagrams. Chemical analyses of these alloys showed their impurity contents to be quite low; therefore, the results obtained should have very nearly coincided with true equilibrium. A survey of the literature disclosed that previous studies had been made with metallographicig or electrical resistivity methods,4'5 but that agreement between results and technique was poor as evidenced in Fig. 1, which also includes the present results for comparison. The discrepancies have been attributed to impurities,3 and this is undoubtedly true in the early work.1'4'5 The latest Studies,''~ conducted with starting materials of higher purity, employed metallographic analysis, a technique that is quite sensitive to local homogeneity and depends strongly on subjective interpretation. In the present work the problem of defining solubility limits was approached in two ways. The first measured a physical property, electrical resistivity, at the equilibrium temperature. The second, a micro-hardness characterization of a diffusion zone, is a room temperature evaluation of a mechanical property under conditions removed from equilibrium. A close correlation between two such basically different approaches would strongly justify confidence in the results. I) MEASUREMENT OF SOLUBILITY OF LITHIUM IN ALUMINUM BY ELECTRICAL RESISTIVITY Experimental Procedure. Alloys for electrical resistivity measurements were made by melting and

Jan 1, 1962

By R. G. Ward

The temperature gradient in the subhearth metal or "salamandern of the iron bhst furnace results in the establishment of gradients in the concentrations of silicon, manganese, carbon, and sulfur. The temperature and compositional variations observed in three blast furnaces are analyzed according to irreversible thermodynamics and the systems appear to be close to the steady state condition. Apparent heats of transport, Q, for silicon, manganese, carbon, and sulfur are found to be respectively -17.5, -5, -2.1, and+22k cal per g mol. In conclusion the significance of thermal diffusion in extraction metallurgy is briefly discussed. INCREASING interest has been shown in recent years in the application of irreversible thermodynamics to metallurgical problems. In particular studies have been made of the transport of matter in thermal gradients1-' and under chemical gradients imposed by a binary solvent However, no detailed example in extraction metallurgy has been reported although gradients are the essence of many extractive processes. The case of the distribution of elements in molten blast furnace iron under a thermal gradient is discussed here. DATA In blast furnace operation the hearth bottom is often extensively destroyed by molten metal, and the metal may penetrate perhaps 10 ft into the furnace foundations forming a "bear" or "salamander". Several hundred tons of molten metal may thus exist beneath the level of the conventional tap hole and remain relatively undisturbed for several years under a thermal gradient. This system is subject to little convective stirring because the temperature decreases from top to bottom, and mechanical stirring due to movements in the stack and to tapping operations is unlikely to penetrate far into the metal. The system may thus be regarded as static

Jan 1, 1963

By H. E. Stauss

THE short-time tensile-strength test, while it has not attained the practical importance of the creep test at elevated temperatures, has the advantage of being rapid and is satisfactory for determining relative strengths. For platinum and its alloys, which frequently are used at high temperatures under ill-defined conditions, the short-time test provides useful data that aid in the selection of the most promising alloy for each use. Measurements have been made upon 13 alloys, using wire 0.0031 in. in diameter, the choice of alloys and of wire size being determined by the requirements of a practical problem. Later the measurements were extended to higher temperatures by the use of heavier wire, 0.010 in, in diameter. APPARATUS The use of fine wire made the necessary equipment very simple, since no effort was made to measure the elongation. A small platinum-wound horizontal furnace was used, ½ in. in internal diameter by 1 ft. long, with the wire threaded through it. The wire, clamped at one end while the other ran over a ball-bearing pulley, of a total length of 29 in., was loaded directly by running sea sand into an attached basket, making the rate of loading and not of elongation constant. The sand flowed from a funnel, under a head of 3 in., into the basket. 3 in. below the orifice, at the rate of 170 grants per minute. Pulley friction and bending resist-ance of the wire as well as the force of impact of the sand could be neg-lected, being 3 grams and 0.5 grams, respectively. Furnace temperature .was uniform within ±5° C. over a length of 3 in., although a drift with time occurred, the largest amount being 20° C. No provision was necessary for a controlled atmosphere.

Jan 1, 1939