Search Documents

By Carle Hayward

THE effect of copper on steel has been studied by numerous investigators. Before modern testing methods had been developed, blacksmiths noted red shortness in iron, the cause for which was ascribed to the presence of copper. Numerous papers have been published on the corrosion of steels containing various amounts of copper, and a few writers have discussed the effect of copper on the mechanical properties of steel. The purpose of the investigation described in the following paper was to obtain additional data on the mechanical properties of medium-carbon steel containing small quantities of copper. Among those who have published results of mechanical tests on copper steels are Ball,1 who states that copper increases the tensile strength and 'hardness but lowers the elongation. Stead2 states that copper steels closely resemble nickel steels containing equivalent percentages of nickel,, as regards tensile strength, resistance to shock, corrosion and hardness. Wigham 5 found that copper in small amounts had no injurious effect on steel. Breuil4 found that with 1 per cent. carbon, copper lessened the brittleness of steel and in low-carbon steel it increased the tensile strength and lowered the ductility slightly. H. H. Campbell 5 states that copper up to 0.25 per cent. slightly raises the elastic limit, elongation and reduction of area.

Jan 1, 1918

By R. Sprycha, J. Szczypa, W. Janusz, J. Neczaj-Hruzewicz

INTRODUCTION Because large aqueous suspensions of various fine solids originate during the beneficiation of ores, the Mining Industry constantly requires efficient and feasible dewatering methods. Among the techniques currently in use (1,2), filtration (vacuum, press) and centrifugation are fairly expensive and thus are limited to use with more valuable materials. Furthermore, installations of reasonable size produce only moderate outputs. Therefore, tailings from ore dressing plants are usually treated by sedimentation or settling techniques with a tailings dam as the ultimate sedimentation basin (3). Apart from growing environmental and economic questions, the solid product obtained from the tailings dam basin has in most cases, a rather high moisture content and a persistent semi-fluid consistency. Thus, it is difficult to transport and use further. On the other hand, the solids may be utilized as a filling material, fertilizer, etc. providing they are dry enough and properly granulated. Demands for an improved technique are met to a great extent, by the technique presented in this paper. AGGLOMERATION OF FLOCCIJLATED SLIMES Origin and Qualitative Description of the Process Phenomena of consolidation and pellet formation in flocculated fines were first observed by Yusa and Gaudin (4) while studying rheological properties of flocculated kaolinite. On this basis, methods of separating liquid from solids have been worked out (5-7) and many possibilities for application have been suggested (5,6). Yusa termed the technique "wet pelletization''.

Jan 1, 1980

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit and a number of surveying technicians, has proven to be a very expensive and time-consuming operation. Now, however, engineers have adapted the laser to help ease the problems of surveying, at the same time increasing the efficiency of such operations. The laser, which projects a continuous, narrow red beam of brilliant light, provides a constant alignment reference that does not interfere with personnel or equipment. A complete laser alignment system, specifically designed for and suited to a variety of mining and tunneling operations, has been developed by the Perkin-Elmer Corp. The engineering significance of this development can be fully realized when it is noted that, aside from potentially tremendous economic advantages in terms of labor savings, the laser beam provides a system of alignment that is at least ten times more accurate than presently used optical systems. The new laser system provides accuracies within 10 microinches per foot (1 x 10-5in.) when used with an accessory centering detector. In one of its first field trials, the laser was used for alignment of a two-mile tunnel which showed a total deviation of less than 5/8 in.

Jan 4, 1968

By G. V. Sullivan, B. E. Davis, T. O. Llewellyn

The Bureau of Mines, US Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8-10.2% P205 and 1.7-4.8% MgO. Chemical analyses of sized fractions indicated that no pebble concentrate, +1.2 mm (+14 mesh) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0-31.3% P205 at flotation recoveries ranging from 72.4 to 96.1% of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36%. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3% P205 and 0.55% MgO could be produced with a flotation recovery of 89.9%. The MgO content of concentrates obtained from the Manatee No. 1 and Hardee samples was 1.20 -1.36 %, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8%, but with a concomitant loss in phosphate recovery of about 10%.

Jan 1, 1985

By E. F. Steeb, P. C. Rosenthal

BlANKS 8 in. long were cut from the as-received bar stock and austenitized at 1560° F for 1 hr, oil quenched, tempered at 1140°F for 1 hr, and water quenched. The heat-treated blanks were machined into tensile specimens which were subsequently used for the straining operation. Some of the tensile specimens were temper embrittled at 900°F for 24 hr and air cooled prior to or following the straining operation. The specimens were strained in tension up to 5 pct total strain (elastic plus plastic) either at room temperature or at 900°F. The reduced sec- tion of the tensile specimen employed was 5 in. long and 0.600 in. in diam. This size specimen was sufficiently large to permit two standard Charpy impact bars to be machined from it. One group of specimens was temper embrittled at 900°F for 24 hr under stress of about 20,000 psi applied with a hydraulic tensile testing machine. Approximately 0.34 pct plastic strain occurred during this treatment. A comparison of series "A" and "B" data in Table I at 0 pct strain, reveals that the steel was rather highly susceptible to temper embrittlement, the embrittling treatment causing the transition temperature to rise 165°F. The 28 ft-lb level, which was near the center of the sharp-rising portion of the transition curve, was selected as the

Jan 1, 1959

By A. L. Slaughter

The Homestake mine, located in western South Dakota, was discovered in 1876. The first reported production was in I 878. Total production through 1965 is 6,554,249 troy ounces of silver and 27,961,276 troy ounces of gold, worth $987,000,000 at present prices. Precambrian sedimentary formations at Lead total 20,000 feet. The Poorman Formation, the oldest, is chiefly ankerite carbonate. The Homestake Formation is iron-magnesium carbonate. The younger formations are argillaceous with some quartzites. The Cambrian Deadwood Formation unconformably overlies the Precambrian. All are cut by Tertiary intrusives. Sideroplesite schist of the Homestake Formation was converted to cummingtonite schist in the zones of higher-grade metamorphism. The Precambrian rocks show the effects of extreme isoclinal folding. A second stage of folding ( cross folds) may have been caused by the Tertiary intrusives. All folds plunge to the southeast. The Homestake ore bodies are pipe-like replacements of the Homestake Formation in zones of cross folding. It is believed that dilatation of the schists has increased permeability in these zones. Chloritization of the schists is the most widespread effect of the mineralization which is divided into four stages. Principal minerals of the first stage are quartz, chlorite, and arsenopyrite; in the second stage, quartz, ankerite, and pyrrhotite. In the third stage only pyrrhotite was deposited. The fourth stage followed the intrusions of Tertiary dikes and deposited mostly pyrite and calcite. Gold accompanies all stages and is always the last mineral to be deposited. It is most closely associated with arsenopyrite of the first stage but can be interpreted as having been deposited during the fourth stage and superimposed on the products of the earlier stages.

Jan 1, 1968

By Charles C. Peterson, Ronald E. Enstrom

Significant improvements have been made in the ursine systern for epitaxial vapor gvowtlz of Gds. The electron concentration has been reduced to below 1015 cm-3 with electron-mobility values as high as 7200 sq on per v-sec at 30PK and 60,000 sq cw7 per v-sec at 77°K. These high-purity layers have been successfully gvown on n&apos; layers with thicknesses as snzall as 1 p and as large as 125 p. Furthermore, high-purity layers have been incorporated into an structure without degradation of electrical properties. Different impurity gradients at the n&apos; to n interface were achieved. Using these structures, Gunn oscillators have been operated at frequencies as low as 0.4 GHz and as high as 40 GHz, which equals the highest valzle yet reported. The frequencies nleasured are in reasonable apeenlent with those calculated fron7 the n-layer widths and the transit times. CW operatiolz has been achieved from 3 to 20 GHz. In Gunn devices for >40 GHz operation (i.e., witk an n-layer tkickness below 2.5p), the n layer has been generally too pure to permit oscillations to occuv. ThE mechanism of the Gunn oscillator&apos; is now generally understood.2-5 Electron transfer from the (000) minimum to the ( 100) minima leads to a voltage-controlled negative resistance, which results in the formation of domains of high and low electric fields which travel through the crystal with a characteristic velocity of about 107 cm per sec. When a constant voltage is applied to the sample, this domain motion generaliy leads to oscillations at the transit time frequency, fT = 107/L, where L is the thickness of the active n layer.&apos; In this case, a single high-field domain is nucleated at the cathode and grows until it reaches the anode, where it is absorbed; a new domain then forms at the cathode.5 There are related modes of oscillation of the same device in which a tuned circuit causes a periodic variation of the voltage across the device. The frequency then may be either above or below fT. It has been shown that oscillations will occur when n • L 2 1012 cm"2, where n is the carrier concentration in the active region. At lower doping densities, 10" 5 n . L 5 lo&apos;&apos;, the doping is said to be subcritical for oscillation and the description of the device operation changes since the domains become comparable in thickness to the device thickness, L. Nevertheless, such devices have been found to be "active" and, in fact, are useful as amplifiers.778 For CW operation, one wishes to minimize the power dissipation, which is related to the electric field, E, and the low-field resistivity, p. Below threshold, the power dissipation density is approximately Typically, at threshold where E -- 3 x 103 v per cm, the dissipation density is 107/p watts per cu cm, p in ohm-cm. Furthermore, it is desirable to provide good conduction of the heat generated in the active region. The temperature rise, AT, across the active layer of a sandwich structure, with a heat sink on one side, is given by AT = (E&apos;/P)(L~/~~) where it is assumed that the thermal conductivity, u, and resistivity, p, of GaAs do not vary appreciably over the range of temperature and electric fields existing in the layer. This expression shows that, subject to maintaining an appropriate (n . L) product, CW operation is favored by a higher resistivity, a lower threshold field, and a thinner device. The above device requirements place some severe restrictions on the materials to be used, especially for high-frequency (>10 GHz) operation. Here, it is necessary to prepare very thin (<10 µ) layers of GaAs, in a state of high purity (-1 ohm-cm), complete with very low-resistance ohmic contacts. Problems of handling such thin and fragile samples become inereasingly severe as the frequency is raised. Furthermore, while good low-resistance ohmic contacts are easily applied to low-resistivity GaAs, contacting difficulties are encountered for these higher-resistivity materials.

Jan 1, 1968

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy&apos;s, was affirmative. It gave reference to Bureau of Mines publications1&apos;5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers&apos; calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm&apos;s length from plane of traverse." I presume that arm&apos;s length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.&apos; One study&apos; has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen&apos; constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.&apos; The spec-

Jan 1, 1953

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By Paul A. Farrar, Sanford Adler

The Tz-Zr system was reinvestigated using both metallographic and X-ray diffraction techniques. It mas found that titanium and zirconium are soluble in all proportions in both the a and 0 phases. The minimum in the transformation was found at 50 at. pct and 535°C. THE Ti-Zr system has previously been the subject of several investigations.1-6 A study by Hayes et al.5 using magnesium-reduced titanium and zirconium melted in graphite crucibles indicated that the system was a continuous series of solid solutions in both a and 0 phases with a minimum at approximately 545°C and 65 pct* Zr. These conclusions were substantiated by the work of Duwez4 as well as by the limited data of Craighead et al.,3 Fast,2 and deBoer.1 However, a more recent investigation of the titanium-rich region by Ence and Margolin6 indicated that the solubility of zirconium in a, titanium at 500°C is approximately 22 pct with the a + 0 field extending to approximately 47 pct Zr. Therefore in order to resolve this discrepancy the following investigation was initiated. EXPERIMENTAL PROCEDURES The alloys used in this investigation were prepared as 20- to 30-g buttons by nonconsumable electrode melting in a helium atmosphere. The starting materials were Bureau of Mines titanium BHN 71 and Foot Mineral iodide crystal bar zirconium. The titanium was premelted before the alloys were prepared to avoid excessive weight losses in the final melting. The compositions of the alloys prepared were as follows: Ti-12.0, 22.2, 29.0, 39.6, 50.0, 58.0, 72.4, 83.5. and 90.8 pct Zr. Prior to heat treatment the alloys were cold-worked 10 to 20 pct, stopping at the first signs of cracking. Specimens for heat treatment were wrapped in molybdenum sheet and annealed in argon-filled quartz capsules for the following times and temperatures: 750°C-40 days, 675°C-61 days, 600°C—109 days, 575°C-112 days, 550°C-112 days, 525°C—127 days, and 450°C —153 days. Quenching was accomplished by breaking the capsules in an iced-brine solution. The standard techniques used for polishing the specimens involved belt grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch7 or "R" etch 8 Debye-Scherrer X-ray powder photograms were obtained for a number of samples using a 114.6-mm camera and CuK, radiation. Exposure times were from 19 to 23 hr. The powder samples were obtained by filing to 270 mesh size. After filing the samples were wrapped in molybdenum foil capsuled in quartz and reannealed at the temperature of original heat treatments; following the heat treatment the samples were quenched into iced brine without breaking the capsules. RESULTS AND CONCLUSIONS On the basis of the microstructural examinations of the heat-treated samples and of the X-ray diffraction data, the Ti-Zr system shown in Fig. 1 was constructed. The data indicate that a, and 0 titanium form a complete series of solid solutions with a, and ß zirconium. The minimum was found to occur at 65 pct (50 at. pct) Zr and 535°C, in excellent agreement with the earlier investigations,1-5 see Fig. 2. Typical microstructures are shown in Figs. 3 to 7. Figs. 3, 4, and 5 show the 22.2, 39.6, and 50.0 pct Zr alloys after heat treatment at 675°C for 61 days with the 22.2 pct Zr showing equiaxed a, and the 39.6 pct Zr alloy a + transformed ß, while the 50 pct Zr alloy shows only transformed B. Figs. 6 and 7 show the 29.0 and 39.6 pct Zr alloys after heat treatment for 109 days at 600°C. The 29 pct Zr alloy has an equiaxed a structure while the 39.6 pct alloy has a partially recrystallized a+ß structure. X-ray diffraction data obtained from the 50 pct Zr alloys after heat treatment at 525° and 450°C as well as from the as-cold-rolled material showed only those lineos which couid be indexed a: a titanium, good agreement with the previously published values. 2,4,5,9 Chemical analysis* of the 50 pct Zr alloy

Jan 1, 1967

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation&apos; of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,&apos;-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals&apos; force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.&apos; The streaming potential

Jan 1, 1970

By A. A. Brant

In this presentation, concepts of the formation and evolution of the universe, the earth, and the cyclic civilizations of man are broadly outlined. The 5 billion or more years of the universe and the 4% billion years of the earth are contrasted to the 5000 years of modern society and the 100 years of objective scientific breakthrough. THE UNIVERSE Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century — from a 5 to 7 hour day to its present 24 — and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away away at velocities increasing with their distances, by 180 km/sec velocity increase for every million light year&apos;s distance. In short, the universe is expanding like an exploded bomb. Comparing the velocity increase per million light year&apos;s distance again indicates a zero time of some 5 billion years&apos; Thus it appears that this universe had a finite beginning. Physical measurements and present theories permit some picture of our universe&apos;s birth. We know since Einstein that many forms of energy are equivalent, e.g., mass, and electromagnetic radiation, aspects of which are heat and light. Now with expansion, radiation density or equivalent mass decreases as a length factor to the 4th power, while mass as matter decreases at a length factor cubed. The temperature in outer space is now perhaps 100° absolute and the radiation mass equivalent is but 1/1000 the rarefied interstellar gas densities. Decompressing the universe to a starting point, however, raises temperature more rapidly than mass density, and results in a high radiation mass energy fraction, which since it is proportional to temperature to the 4th power suggests a zero point temperature of several billion degrees, brighter than any sun. "Let there be light and there was light," according to Genesis 1-3. Now what further initial conditions must there be to explain the relative abundance of the elements in the universe, which by spectral analyses of the earth&apos;s crust, stony meteorites, and the sun and stars is surprisingly uniform throughout. Some 55% of all cosmic matter is hydrogen, some 44% is helium and only 1% is made up of all the heavier elements in much the same proportions as on earth. These latter decrease logarithmically in abundance up to atomic weight 100, then level out. This consistent abundance distribution of elements in the universe may be generally explained by taking at Time Zero a hot neutron gas of density about 10-3 grams per cc, at a temperature of several billion degrees Centigrade, with a high radiation energy fraction. Generally neutrons break down into positrons and electrons within about ten minutes, but at the initial high temperature and radiation pressure would recom-bine. However, with rapid expansion and decrease of temperature and pressure, the neutron disintegration would run uncompensated and aggregation would result from neutrons and protons uniting in different degrees of complexity. The total calculated element aggregation time would be about one hour while the temperature still remained above one billion degrees. The element abundances formed would depend on density of the nuclear gas, simplicity of the atom formed, and the neutron capture cross section. Thus a higher density

Jan 1, 1964

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By H. C. Fiedler

The development of cube-on-edge secondary re crystallization texture in Si-Fe strip depends upon the ability of inclusions, such as manganese sulfide, to restrain nomal grain gvowth. The ability of inclusions to perform this function is shown to depend upon their size and distribution. The desired uniform dispersion of many small inclusions is obtained by controlling the cooling rate from above the solution tempmature of the inclusions or, alternatively, by drastic &apos;quenching from above the solution temperature followed by heat treating at a lower temperature. The development of the cube-on-edge secondary recrystallization texture in Si-Fe strip depends upon both establishing the proper primary recrystallization texture and having inclusions to restrain normal grain growth. It has been suggested that the first requirement is met with a texture which, though weak, is near (110)[001]. A mechanism for secondary recrystallization originally proposed by ielsen&apos; is consistent with the presence of this primary texture. It is visualized that a secondary grain appears where two adjacent grains happen to be sufficiently similar in orientation to be capable of behaving as a single large grain. This pair of grains will grow at the expense of its smaller neighbors as a consequence of its having lower grain boundary free energy. Other explanations of the origin of the secondary recrystallization texture have been offered,&apos; and it can be concluded that the mechanism is not fully understood. Nevertheless, it is apparent that operationally the necessary primary recrystallization texture is obtained simply by interposing an anneal during the cold reduction to final gage. The role of inclusions in the development of the secondary recrystallization texture has been demonstrated by May and Turnbull4 in a comparison of a high-purity heat and a heat containing manganese sulfide. They showed that the driving force for secondary recrystallization is inversely proportional to the diameter of the matrix grains and that the function of the inclusions is to maintain a small matrix grain size. Other inclusions, such as various sul- fides,&apos;)&apos; silicon nitride,8 and vanadium nitride,&apos; titanium carbide,&apos;&apos; and vanadium carbide," have been shown to be effective in promoting secondary recrystallization to the cube-on-edge texture. There is also evidence that silica inclusions in Si-Fe strip made by powder-metallurgy techniques perform this function.&apos; This report is concerned with the second of the two requirements for secondary recrystallization, namely the importance of the metallurgical control of the size and therefore number of inclusions. While the concepts involved are simple, they are fundamental to the making of this material. EXPERIMENTAL PROCEDURE A heat containing 3.27 pct Si, 0.026 pct S, 0.06 pct Mn, and 0.004 pct C was made in an air induction furnace from electrolytic iron, 98 pct ferro-silicon, electrolytic manganese, and iron sulfide. The heat was divided between graphite and baked-sand molds with a cavity 2-5/8 by 5 in. and with walls 2-3/4 in. thick. Slabs, 1 in. thick and 2-5/8 by 5 in., were cut from the ingots and hot-rolled either in the as-cast condition or after one of the heat treatments described later. After pickling, the 80- to 100-mil-thick hot-rolled band was, unless otherwise noted, heat-treated for 5 min at 900°C before being cold-rolled to 25 mils. After a heat treatment of 1 to 3 min at 860°C, the strip was cold-rolled to 12 mils, the final thickness. The percent cube-on-edge texture was determined by dividing the maximum torque as averaged from four samples by the maximum torque of a 3-1/4 pct Si-Fe single crystal having the (110) plane in the plane of the sample. The torque measurements were made in a field of 1000 oe on 1-in.-diam disks. RESULTS AND DISCUSSION The importance of the thermal history of the ingot is evident in Fig. 1 from the appearance of strips heat-treated in a temperature gradient. The sample

Jan 1, 1964

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.&apos; The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.&apos; The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By W. C. Thurber, C. J. McHargue

THE deformation textures of metals have been extensively studied because of both the practical implications in metal fabrication and the fundamental insight into the behavior of the metal during deformation. Most studies have been concerned with pure metals or solid-solution alloys and relatively little attention has been directed toward more complex alloy systems. Barrett&apos; and Brick2 have summarized work on multiphase systems in terms of the relative ease of deformation of the phases. Thus, if the phases are deformed about equally, each develops its usual texture for the particular fabrication process. This behavior has been reported for Ag-Cu and Cd-Zn alloys3 and 62-38 brass.4 A dispersion of hard particles in a softer matrix interferes with the normal reorientation of the matrix lattice during deformation, thus distorting the texture or in some cases preventing its development. Increasing the amount of carbon in steel has been observed to increase the randomness of the ferrite5 and almost random textures have been reported for A1-12 pct Si eutectic alloy wires.6 It has also been noted that if the second phase is platelike, deformation causes the platelets to line up in a common direction. The present work concerns a quantitative study of the deformation textures in aluminum-uranium alloys containing 5 or 13 wt pct U. Alloys in this composition range are characterized by a pure aluminum matrix in which the intermetallic compound UA14, is dispersed. From a fundamental standpoint, this system affords the opportunity for studying the effects of a dispersed phase on texture development in an essentially pure metal matrix. Further, these alloys are commonly used as fuels for nuclear research and testing reactors, and a knowledge of the preferred orientation may be useful in evaluating physical and mechanical properties as well as response to fabrication. The deformation textures in sheets of aluminum (99.996 pct), Al-5 pct U alloy, and Al-13 pct U alloy were determined for reductions in thickness of 90 pct by cold rolling. The texture in an alloy rod of the latter composition which had been extruded at 455°C was also determined. It can be readily ascertained from the aluminum-uranium phase diagram that the 5 pct U alloy is hypoeutectic and contains 7.3 wt pct (3.4 vol. pct) UAl4. The 13 pct U alloy has the eutectic composition and contains 18.9 wt pct (9.4 vol. pct) UAl,; however, because of nonequilibrium solidification conditions, the typical eutectic microstructure was not developed. The alloys were prepared by open-air melting in graphite crucibles. The slab castings were cropped and cold reduced 90 pct in thickness on a two-high mill. The slabs were reversed after each pass. Although the uranium-bearing alloys exhibited edge cracking, they could be cold rolled to the desired thickness. Small coupons 1.5 by 0.75 by 0.1 in. thick were sheared from the center of the rolled plate with a major axis parallel to the rolling direction. To obtain a specimen of sufficient thickness for machining of the X-ray diffraction specimen, three coupons were laminated into a single three-ply sandwich with a suitable adhesive. Adhesives which could be cured at room temperatures were selected in order to prevent recrystallization during bonding. Bondmaster M-648 (Rubber and Asbestos Corp.) was used for the pure aluminum laminate and Armstrong A-6 (Armstrong Products Co.) was used for the alloys. The alloy for extrusion was cast in a cylindrical graphite mold! cropped and machined into a 3-in. diam by 4-in. long billet. This billet was preheated to 455°C, upset to 3.125 in. diam, and extruded on a 700-ton hydraulic press at a speed of 6 fpm through a flat-face, 1-in. diam die. The rod was quenched with a water spray as it emerged from the die. Pole-distribution data were obtained using the diffractometric method described by Jetter and Borie.7 A spherical X-ray diffraction specimen of

Jan 1, 1961

By Arnulf Muan, D. P. Masse

PHASE relations in the system CoO-SiO2 have been determined as a basis for further investigations of thermodynamic properties of olivine solid solutions involving Co2SiO4 as a component. Previous data on the system CoO-SiO2 are incomplete or uncertain. Biltz and Lemke1 determined the melting point of cobalt orthosilicate as 1345°C , but Asanti and Kohlmeyer2 have later found a considerably higher temperature, 1420°C. The latter authors also studied melting relations of one mixture on the CO side and two mixtures on the SiO2 side of the orthosilicate composition and sketched a tentative phase diagram for a limited composition range of the system. However, no phase identification was carried out, and the authors left unanswered the question of the possible existence of a stable meta-silicate phase. Greig3 showed that a 90 wt pct SiO2-10 wt pct Co mixture at 1725°C consists of two immiscible liquid phases. The quenching technique was used in the present investigation. Mixtures of high-purity cobalt oxide ("Fisher Certified") and dehydrated silicic acid ("Baker Analyzed") were equilibrated in air atmosphere. The samples were then quenched to room temperature and the phases present were identified by microscopic and X-ray examination. The samples were kept in small envelopes made from thin (0.0004 in.) platinum foil. Thermodynamic data which have become available recently for Pt-Co alloys4 were used to check that the losses of COO from the oxide samples by alloying of cobalt with platinum in the present investigation were too small to change significantly the compositions of the oxide material during the equilibration. A vertical tube furnace with an 80 pct Pt 20 pct Rh resistance winding was used in runs up to 1510°C. Temperatures in these runs were measured with a Pt vs 90 pct Pt 10 pct Rh thermocouple calibrated against the melting point of diopside (CaMgSi2O6, 1391.5?C). The given temperatures as measured by this technique are estimated to be accurate to *5°C. Quench runs at temperatures above 1650°C were made with a modified Roberts and Morey5 strip furnace, using strip resistors composed of a 60 pct Pt-40 pct Rh alloy. Temperatures were measured with an optical pyrometer which was calibrated against the liquidus temperature of a mixture composed of 10 wt pct CaO, 90 wt pct SiO2 (1707°C). The temperatures measured with this technique have an estimated accuracy of +15°C. The results are shown graphically in Fig. 1. Only one intermediate phase, the orthosilicate Co2SiO4 with olivine-type structure, is stable in addition to the end members cobalt oxide and silica. The melting point of the orthosilicate was found to be 1415" ± 5°C. The metastilicate CoSiO3 is not stable at the temperatures of the present investigation. The two eutectic points in the system CoO-SiO2 where COO plus olivine, and olivine plus silica, coexist with liquid were found to be 72 wt pct COO and 1407°C and 63 wt pct COO and 1381°C, respectively. The melting point of cobalt oxide in air was taken as 1745?C, based on the previous data of Aukrust and Muan.6 Within limits of error (+ 5?C), identical eutectic temperatures to those determined in air were found when two representative mixtures were equilibrated at 1 atm O2 pressure and in an atmosphere of 84 vol pct CO2, 16 vol pct H2. This suggests that changes in oxidation state of cobalt in the condensed phases are not significant as far as their effect on the phase relations are concerned. This inference was substantiated by failure to detect7 any "excess oxygen" (i.e., oxygen in excess of that contained in Co2SiO4) in a sample of orthosilicate composition equilibrated in air 10°C above the liquidus temperature and subsequently quenched to room temperature. This work was carried out as part of a research program sponsored by the U.S. Atomic Energy Commission under Contract No. AT(30-1)-2781.

Jan 1, 1965

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.&apos; Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.&apos; Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951