Search Documents

By A. J. Opinsky, J. L. Orehotsky, L. L. Seigle

TUNGSTEN incandescent lamp filaments possess a typical structure of elongated crystals generated upon heating the silica-alumina doped wire rapidly to 2200°C or above.&apos; It is known that these very long grains exhibit a preferred orientation, but there is disagreement in the literature about the direction. Rosi,2 and later Rieck; reported that the <135> direction of the large grains in doped wire tends to be parallel to the wire axis, but other investigators have reported that <110> is the preferred direction. Some further investigation of the orientations of large grains in tungsten wire is reported in the following. In the first series of experiments, 6-in. lengths of wire were heated rapidly in a bell jar. Current was passed through the wires and within 15 sec the wires had reached the grain coarsening temperature. 2 min was the annealing time. Wires were heated in hydrogen, nitrogen, and vacuum. Later, wires were heated in an evacuated tube furnace in which the tube was brought from 1000°C to the operating temperature within 25 sec and held 5 min at temperature. Temperatures were measured with an optical pyrometer. After heating, the wires were electro polished and etched, and the orientations of the large grains determined by the Laue back-reflection technique. Most of the experiments were carried out on a single spool of 5-mil silica-alumina doped wire, but a few tests were made with 5-mil thoriated tungsten wire and 10-mil undoped wire. 5-mil silica-alumina doped wires were reduced to smaller diameters by electropolishing for one series of experiments. Orientations of the large grains in silica-alumina doped wire heated in various atmospheres are presented in Figs. 1 and 2 as plots of the direction of the wire axis relative to the cube axes of the crystals. For most of the conditions studied, the preferred orientation cannot be described as a single direction, but the points might be said to group themselves about the arc passing through <110> and <113>. This arc is the trace of the (211) planes and contains the <135> and <124 as well as <011> directions previously observed by other investigators. The preferred orientation of large crystals in silica-alumina doped tungsten wire might be most generally described, therefore, by stating that a (211 ) tends to be parallel to the wire axis. This is true also for wires reduced in diameter by etching and furnace heated, Fig. 2, i.e., the recrystallization texture is apparently unchanged upon removal of the outer layers and substantially independent of the temperature gradient within the wire.

Jan 1, 1962

By Nathaniel Herz

(San Francisco Meeting, September, 1915) THE use of zinc dust for precipitating the precious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been clone on methods of testing zinc dust, as yet no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some observations made while testing. a large variety of zinc-dust samples in the laboratory. W. J. Sharwood1 has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J. E. Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of `99 0&apos; potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more KCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 cc. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grains of pure crystallized KAg(CN)2 may he dissolved in a liter of water and 1.5 grams KCN added. "Weigh out 0.5 grain zinc dust into a 300-cc. beaker. Add a few cubic centimeters of water and stir until, zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, plaice in a scorifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efficiency."&apos;

Jan 8, 1915

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By Sherwin F. Kelly

GEOPHYSICS may be considered a vice (albeit, I submit, a comparatively harmless one) whose career is aptly described by Pope&apos;s lines: Vice is a monster of so frightful mien, As to be hated needs but to be seen; Yet too oft, familiar with her face, We first endure, then pity, then embrace. Although there may be some that have not yet succeeded in emancipating themselves from the first stage of horrified contemplation, geophysicists may be duly thankful that there are mining men and geologists that have arrived at a state of apparently irretrievable damnation.

Jan 1, 1936

By A. B. Stickney

UPWARDS of 200,000 engineers in this country are sufficiently interested in engineering as a profession to have joined a society, but not over 10% of them belong to any one society. There is a widely-felt need of an over-all organization of all the societies to act as spokesman for all engineers on matters of common concern. On a local basis, over 100,000 engineers in 35 metropolitan areas have organized themselves into local councils, and are doing an effective job of intersocietal co-operation within their sphere of activity. In the last few years much has been said and written about a similar organization on a national scale. Everybody wants iteverybody is talking about it-it&apos;s in the air-it&apos;s coming-it&apos;s inevitable. Although it is no longer necessary to talk about why or whether there should be such an organization, there is no such unanimity about what it should be like. This paper outlines a proposed organization by answering four questions-who, how, what, and who will pay for it.

Jan 1, 1946

By F. S., Mc Nicholas

A practical discussion of the theory of A block caving is presented which applies particularly to the physical conditions of the Climax orebody although the conditions are sufficiently characteristic of caving ore-bodies to provide valuable information applicable elsewhere.

Jan 1, 1950

By Ross Blake

THE St. Joseph Lead Co. became interested in the Tri-State district in 1921 through acquisition of prospecting and development rights on approximately 20,000 acres of land extending northeastward from the Picher mining field, mostly in Kansas. Prospecting with churn drills was begun the same year and the first commercial ore body was found on the Jarrett tract at the then northern limit of the main Picher field. Operations at this mine began in 1923. Kansas Explorations, Inc., was organized in 1923 by the St. Joseph Lead Co. as a wholly-owned subsidiary to carry on its operations in the Tri-State District from an office at Joplin, Mo. As prospecting of the original acreage proved largely negative, attention was subsequently turned to other sections of the district. Numerous additional leases were acquired and prospected. The Company was successful in developing into operating properties the Jarrett, Isherwood, Robinson, Sullivan and Lotson tracts and, in more recent years, the Ritz, Snapp, Buckingham, Gibson and Jasper mines.

Jan 1, 1947

By W. G. SWART

THE best estimate on reserves of iron ore in the Lake Superior district is that made, in 1920, by Mr. R. C. Allen, amounting to 2,947,225,000 tons of assured and probable ore. This includes direct- shipping or so-called merchantable ores, and those capable of beneficiation by demonstrated processes. De- ducting from this the 287,000,000 tons shipped since 1920, leaves a present reserve of approximately 2,500,- 000,000 tons, or; about 50 years&apos; supply. The assured ore in this estimate is given as 1,560,500,000 tons, which checks Mr. Lake&apos;s estimate of 1,528,948,000 tons, or about 30 years&apos; supply. This is not a long time in the life of the steel industry, and it can be readily appreciated that the matter is important enough to war- rant the attention it is beginning to receive. The first question that engages our attention is, What is merchantable ore? In 1902 the average of all Mesabi shipments was 56.07 per cent iron and 4.35 per cent silica. Twenty-five years later it had dropped to 51.99 per cent iron, with silica up to 7.92 per cent. It has remained around these figures for&apos; ten or twelve years and, except for a probable rise in silica, can stay there for an indefinite period. Most of these figures I am giving cover the Mesabi Range. Including the other ranges does not change the figures greatly, and the Mesabi Range commands the situation, since it produces about 65 per cent of the total annual tonnage and, according to Mr. Allen, contains 81 per cent of the assured reserves, 50 per cent of the probable reserves, and 66 per cent of both the assured and the probable reserves.

Jan 1, 1926

By J. S. Marsh

AN incomplete statistical analysis performed wearily on the morning after Thursday, Feb. 12, indicates that the unavoidable items of conversation among steelmen were the current shortage of sleeping time and the "Normandie." No analysis is needed, however, to be certain that many thousands of valuable words were uttered, both in and out of technical sessions, concerning matters of deep interest to members of the Iron and Steel Division. The opening session consisted mostly of papers that have appeared, or will appear shortly, in Metals Technology. One, however, that was not finished in time to be printed in any form, but that aroused great interest, was by E. L. Ramsey and L. G. Graper (Wisconsin Steel Works). Its subject was the production of high-sulphur steel by treatment with sulphur dioxide derived from anhydrous sodium sulphite or bisulphite added to the ladle or to the mold. The sulphide distribution in the finished steel is such that increased machinability and longer tool life result. Both items are of obvious importance in these days of mighty production.

Jan 1, 1942

By Philip S. Mathews

THE tremendous stimulus given to the mining industry by the gold and silver policy of the present administration has found the capital market for mines ill prepared to afford practical means of financing. Particularly has this been true of the host of abandoned high-cost producers and prospects which increased gold and silver prices have made potentially profitable. In a comparatively short time, experience has demonstrated abundantly that valuable properties have frequently failed to secure capital, while questionable properties have drawn to themselves and their promoters more of the public moneys than their prospects justify. Singularly enough the fault is usually attributable to faulty financing. Discussion and study of this problem are vital to the industry.

Jan 1, 1936

By R. T. DeHoff

A theoretical development is presented which reformulates Fick&apos;s first law for diffusion in the solid state. The diffusion flux of component i in a multi-component system, Ji, is related to its local concentration, ci, and local jump frequency, ri : where a is a geometric factor and d is the jump distance. The product, ciri , is defined as the local concentration of atomic jumps for component i. The analog to Fick&apos;s second law is also derived. A solution to this equation is presented, which permits the experimental determination of the variation of atom jump frequency with composition in multicomponent systems. HISTORICALLY, the description of diffusion in the solid state has been presumed to be best approached as an application of more general diffusion laws, known as the phenomenological equations. These equations relate the flux, Ji, of the various components, expressed in atoms, grams, or volume, to the driving force involved, expressed as either a compositional or chemical potential gradient, sumption that the flux is simply proportional to the driving force is the foundation of this approach. The phenomenological equations take the form: where the concentration gradients are assumed to be the driving force, and: if the chemical potential gradient is taken as the driving force. The coefficients Dij in Eq. [1.] are the "diffusion coefficients"; the elements of the corresponding matrix in Eq. [2], the Mij, are called the "mobilities". Eqs. [I] and [2] may be considered to be definitions of these phenomenological coefficients. A formidable body of literature has been generated about these equations; this literature dates back to their original formulation for the simplest case of binary diffusion in a fluid, by Adolf Fick, in 1855.&apos; This description has been shown to be self-consistent. However, the "constants of proportionality", the Dij or ,Mij, are not constant: they vary with composition in all but the simplest systems. Even in the case of tracer diffusion, wherein it can be shown that the diffusion coefficient is constant, the mobility, which is considered in irreversible thermodynamics to be the more physically meaningful quantity, varies with the concentration of the tracer involved.&apos; In more complex systems, it is necessary to evaluate the entire matrix of phenomenological coefficients, as a function of composition, in order to describe diffusion locally. Further, in order to determine this matrix experimentally, it is necessary to produce diffusion couples that have different sequences of compositions; the matrix may be evaluated only at points where these "composition paths" cross.* Finally, and perhaps most

Jan 1, 1969

By William N. Poundstone

To forecast the future of coal intelligently, one must first consider the market outlook. Coal can be used for many purposes, but currently about 25% of it goes into metallurgical coke, while 75% serves as fuel. Coal for metallurgical coke should show a modest growth for at least the next decade, primarily because of increased exports, but the important factor in the coal outlook is energy. Today, this country faces a serious shortage of energy, and its requirements are growing at an almost unbelievable rate. Last year the United States consumed 68 quadrillion Btu, or double the energy it consumed in 1950, and, if projections are correct, this figure will grow to 150 quadrillion Btu by 1990. Thus, in one working lifetime, the nation&apos;s energy consumption is expected to increase by roughly five times. The future of coal hinges on its degree of participation in meeting this energy need. The Federal Power Commission predicts that coal consumed by electric utilities will increase about 4-576 per yr, reaching 472 million tons by 1980 and 615 million tons by 1990. If this projection proves correct, 1980 consumption will be double that of last year and, even more startling, the utility industry alone will use more coal in 1990 than the entire coal industry produced in 1970. This is a tremendous increase, but in view of the projected energy growth, it is difficult to see how this country&apos;s needs can be satisfied with- out a coal contribution of this magnitude. Unless some new source such as solar energy is discovered, it must be assumed that the projected energy will come principally from the present-day sources-oil, gas, nuclear materials and coal.

Jan 1, 1971

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter&apos;s tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.&apos; The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"&apos;, an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By V. O. Struebing, K. A. Johnson, F. H. Ellinger, C. C. Land

The system Pu-Ce-(Pu,Ce)Co2 has been investigated by thermal, micrographic, and X-ray diffraction methods. The principal characteristics of this system were found to be: 1) a "eutectic" valley extending across the phase diagram from the 6 Pu/Pu3 Co eutectic at 408°C to the 7 Ce/Ce24Co11 eutectic at 42Z°C, the maximum temperature in the valley being 443°C; 2) three ternary inter mediate phases, each having an appreciable mutual solid solubility for plutonium and cerium; 3) eleven four-phase equilibria comprising one eutectic, four peritectics, and six Class II reactions; 4) a pseudobinary section between the ternary phase A and the y Ce solid solution, and another such section between the 6 Pu solid solution and the 77 phase (Pu3 CO) containing cerium in solid solution. ALLOYS of plutonium that are completely molten at temperatures in the vicinity of 500°C are of interest for use in the liquid state as fast reactor fuels. Since exploratory work1,2 on Pu-Ce-Co alloys had indicated that a "eutectic" valley extended across the ternary system between the Pu-co[6 Pu/n (Pu3co)] and the Ce-CO[? Ce/? (ce24co11)] binary eutectics, thus allowing alloys of any plutonium concentration to be selected within the temperature limitation, the present investigation was begun for the purpose of accurately defining the "eutectic" valley. However, when the existence of three ternary intermediate phases and the consequent complexity of the liquid-solid equilibria were discovered, the investigation was expanded to cover the complete system, except for the corner between the isomorphous series PuCo2-CeCo2 and pure cobalt. 1) EXPERIMENTAL The purities of the alloy components are given in Table I. Alloy buttons, each weighing about 5 g, were prepared by arc melting the accurately weighed components (±0.1 mg) under a purified He-Ar atmosphere. Weight loss as a result of melting was usually less than 1 part in 1000; therefore, the buttons were not chemically analyzed. One half of each button was re-melted by induction heating in vacuo in a magnesia crucible and furnace-cooled, so as to produce a somewhat coarser microstructure than that of the rapidly cooled arc-melted button. About 20 g of each alloy to be examined by thermal analysis were remelted in vacuo in a tantalum crucible of the inverted thermocouple well type. The thermal, X-ray diffraction, heat treating, and micrographic methods used in this investigation were essentially the same as have been described in earlier reports.3,4 Two etchants for these alloys were found to be satisfactory: A) 8 (parts by volume) orthophosphoric acid, 5 ethanol, and 5 glycol; B) 7 tetraphosphoric acid, 36 water, and 57 2-ethoxyethanol. Etchant A was used at 5 to 6 v for 15 to 20 sec, and etchant B was used at 10 v for 10 sec. 2) THE LIMITING BINARY SYSTEMS 2.1) Plutonium-Cerium. The phase relationships of this system have been investigated by Ellinger, Land, and Cramer,5 and by Selle and Etter.6 The over-all agreement of their phase diagrams is good, but there are some discrepancies in the positions of some phase

Jan 1, 1967

By G. Y. Chin, A. R. Von Neida

The relationship between crystalline texture and magnetic anisotropy in a Co-10 pct Fe alloy has been investigated by means of X-ray pole .figures, hysteresis-loop tracings, and magnetic-torque measurements. The cold-rolled texture of a sample after 95 pct thickness reduction is of the "brass-type", that is, (110)[112/. At 500°C the cold-rolled material recrystallizes fo a (311)[112] orientation, plus a minor (210) [001] component. This texture persists up to 1400°C, at which point it is replaced by a secondary recrystallization texture, (111)[112]. Magnetic-torque measurements show that the easy axis of magnetization lies along the transverse direction in the cold-rolled material and changes to the rolling direction after primary recrystallization. This change is also reflected in the hysteresis characteristic; whereas the B-H loop along the rolling direction is nonsqunre with a low value of residual induction (750 vs 19,000 gauss at saturation) for the cold-rolled material, the annealed sample exhibits a very square loop with a large value of residual induction (16,000 gauss). Theoretical torque curves calculated from the texture data on the basis of magnetocystalline anisotropy energy compare favorably with the observed torque curves. Values of the crystal anisotropy constant, K1, obbained from these comparisons are in good quantitative agreement with single-crystal data. Furthermore, both the torque amplitude of the poly crystalline material and the magnitude of K1 obtained with a single crystal show an identical temperature dependence over the range from —195° 10 +220°C. It is thus conclzided that the magnetocrystalline anisotrpopy erlergy is chiefly I-esponsible. for the nzagnetic allisotropy of textured Co-10 pct Fe alloy. THE results of a study on the relationship between crystalline texture and magnetic anisotropy of an alloy containing 90 pct Co and 10 pct Fe by weight are reported in this paper. The alloy has an fcc structure: a saturation magnetization of about 19,000 gauss,2 and a nearly zero value of magnetoatriction.3 puzey4 has reported a large crystalline anisotropy constant of -7.4 X 105 ergs per cu cm, indicating the (111) directions as the easy axes of magnetization. Hence, texture variations resulting from cold work and annealing are expected to introduce a magnetic anisotropy in the polycrystalline material through the alignment of these (111) easy directions. In the present study, magnetic anisotropy of both rolled and annealed strips was determined by magnetic-torque measurements and hysteresis-loop tracings The results were correlated quantitatively with calculations based on texture data obtained by the X-ray pole-figure technique. It is established that the magnetocrystalline anisotropy energy is indeed chiefly responsible for the magnetic anisotropy of textured Co-10 pct Fe alloy. EXPERIMENTAL Material Preparation. The alloy nominally contained 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn by weight, the chief impurities being nickel, carbon, and silicon (less than 0.5 pct total). The cast ingot was rolled to strips 10 mils thick and slit to 1 in. in width. After strand annealing at 900°C in a hydrogen atmosphere, these strips were further cold-rolled to various thicknesses down to 0.25 mil (97.5 pct reduction), with samples collected for study of the development of texture and magnetic anisotropy as a function of thickness reduction. subsequently, samples cold-rolled from 100 mils to 0.25 mil were obtained, thus extending the thickness reduction range to 99.75 pct. In addition, 0.5-mil samples cold-rolled from 10 mils were selected

Jan 1, 1965

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.&apos; Previous investigators&apos;&apos; have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana&apos; showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By F. W. Warnaars

The Los Bronces copper deposit is located on the west side of the Andes Mountains in central Chile about 54 km (34 miles) northeast of Santiago. The deposit consists of a hydrothermal breccia complex that was emplaced in the western part of an earlier porphyry copper mineral system. This system exhibits propylitic, sericitic, silicic to potassic hydrothermal alteration with disseminated and stockwork copper-molybdenum sulfide mineralization over an area of about 12 km2 (5 sq. miles). The Rio Blanco Mine, about 800 m (0.5 miles) east of Los Bronces, is an underground block caving mine located in the central part of this system. The mineralization at Rio Blanco is characterized by one of the highest primary copper grades known for porphyry copper systems. Present mining at Los Bronces is from an open pit located in the northern part of a hydrothermal complex that is composed of at least seven different copper-bearing tourmaline breccia pipes. Together these pipe form one large contiguous body about 2 km (1.2 miles) long and 0.7 km (0.4 miles) wide at the surface. This body crops out at elevations of between 3.5 and 4.1 km (2 and 2.5 miles) above sea level. Each breccia pipe has a characteristic shape, matrix, type and degree of mineralization and alteration. Quartz, tourmaline, specularite, anhydrite, pyrite, chalcopyrite, sericite, chlorite, and rock flour are present in significant quantities in most breccia matrices. The clasts consist mainly of quartz monzonite, andesite, and minor amounts of quartz latite porphyry. The seven different breccia pipes are identified, from oldest to youngest, as Ghost, Central, Western, Infiernillo, Fine Gray, Anhydrite, and Donoso. The breccias coalesce, interfinger, or display gradational contacts. In places they form sharp contacts with each other and with the surrounding intrusive or volcanic host rocks. Early breccias are disrupted or cut by subsequent breccia events. Explosive emplacement was followed by collapse after the release of hydrothermal pressures. The Los Bronces breccia complex has sharp contacts with the surrounding intrusive stock and andesites. These contacts dip inward on the north, west, and south margins. The eastern contact is nearly vertical and/or dips slightly outward and suggests a westward tilting of the body of about 15° after emplacement. The breccia complex is not fully explored at depth, but is known to extend at least below the 3 km (2 mile) elevation in its central eastern part, about 1 km (0.6 miles) below the highest breccia outcrop. Primary copper sulfide minerals are most abundant in the Donoso and Infiernillo breccias where the matrix consists mostly of tourmaline, quartz, sulfides, specularite, and/or chlorite with minor amounts of rock flour, sericite, and clay. The volume of the matrix material is mostly smaller than in the other breccias. Secondary enrichment enhanced the primary copper grade in the southern two-thirds of the Los Bronces breccia complex and in much of the surrounding porphyry system. Primary grades of 0.3% to 0.5% copper have been enriched to approximately 0.9%. This enrichment may extend from surface outcrops to a depth of more than 500 m (1, 640 ft) in more permeable parts of the breccia complex. A leached and oxidized capping of variable thickness covers a large part of the enriched layer and exceeds 300 m (984 ft) at one location. The shape and depth of the enrichment blanket and the capping suggest that the enrichment process is still active.

Jan 1, 1983

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

By S. A. Braley

THE first commercial production of bituminous coal in the United States was in 1820, and formation of acid in the areas from which the coal was removed began at that time. Thus it is 130 years since the development of mine acid began. The coal operator has had to deal with the acid water produced in his mines, and his losses from corrosion of pumps and equipment have been tremendous. Other industries and the public have been forced to spend large amounts for their water requirements because of the acid discharge from the mines. There are many contradictions in the literature on this subject probably because of variations in the analytical procedures followed and differences in the methods of calculation and reporting. The opinions previously expressed may be summarized as follows: The production of mine acid has been looked upon as a simple chemical reaction wherein the oxygen of the air has reacted with pyrite to produce ferrous sulphate and free sulphuric acid. This reaction appears in many chemistry texts and generally has not been considered worthy of further study. Since the measurement of hydrogen ion concentration or activity was developed and expressed in terms of pH, indicator and instrumental methods for pH determination have become readily available, making it natural to think of it as a measure of acid content. Special purpose analytical methods applicable to potable waters, sewage effluents, and boiler waters, based in general upon the determination of what may be regarded as impurities, have been applied to more concentrated solutions constituting mine discharges, without reference to the fact that these specialized procedures had been developed to serve as operating guides for water-treatment plants. It has been assumed that the pounds of acid deliv- Table I. Showing pH and Titratable Acid of Varying Concentrations of Ferrous and Ferric Sulphates Ferric Ferrous ion Acldfty Ion Acidity (Fe+++) ppm CaCO3 We++) ppm CaCOa ppm PA equiv. PPm pH equiv. 11.200 1.80 30,000 11,200 3.98 20,000 5,600 2.01 15,000 5,600 4.15 10,000 2,800 2.21 7,500 2,800 4.41 5,000 1.120 2.48 3,000 1,400 4.68 2.500 560 2.60 1,500 140 5.00 250 280 2.65 750 28 5.00 50 112 2.81 300 56 3.07 150 28 3.38 75 ered by a mine was roughly a constant varying with the number of acres mined, and that the concentration of the acid in the drainage was inversely proportional to the volume of flow. Increased flow was thought to result in a dilution of the acid produced. When the Sanitary Water Board of the Commonwealth of Pennsylvania established a fellowship at Mellon Institute, the first approach to the problem was to review some of the chemical reactions involved and their relation to acid production. Since the sulphates of iron were among the principal constituents of coal-mine drainage, the first studies were based upon solutions of chemically pure ferrous and ferric sulphate. These are both neutral salts, that is, the iron and the sulphate are equivalent, but they produce acid reactions in water solution because as salts of strong acids with weak bases, they hydrolyze to form acid solutions. Solutions of each salt, of varying concentrations, were prepared and the pH, titrable acidity and iron and sulphate

Jan 1, 1952

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel&apos;s paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel&apos;s attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,&apos;, y uranium, and perhaps zirconim.&apos; The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors&apos; reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato&apos;s value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,&apos;&apos; and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener&apos;s predictions.28 We have no quarrel with Hagel&apos;s placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963