Search Documents

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.''' Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80'~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

By Charles Bohdanowicz

The accompanying tables' show that in 1936 production of crude oil in Poland decreased very slightly (Tables 1 and 5), by about 1 per cent, and that gas production increased by about 11 per cent. As in preceding years, drilling (Tables 1, 2 and 3) was devoted principally to extension of oil fields in the Jaslo district (fields 1, 5 and 7) and, in a lesser degree, of those in the Stanislaw6w district (field 27). Production of crude oil is being sustained in a large measure by the deepening of old wells; besides a total number of 183 new wells completed (Table 3) about 152 wells were deepened, and in a general way the results of deepening were better than those of new wells drilled. Reserves of "proved land" have not increased as far as crude oil is concerned, but a notable extension of gas fieldsZ was attained in Daszawa (field 25) and in the Roztoki area (field 5). In the sub-carpathian zone gas fields have been proved in the vicinity of Kalusz, Kos6wJ and in the northwestern sector of that zone, between Tarnow and Lezajsk. The gas horizons of Daszawa occur in the Upper Tortonian, those of Kos6w in the Lower Tortonian (Middle Miocene). Exploratory drilling has been performed near Kalusz, and has been commenced near Kos6w and in the Tarn6w area. The Kos6w gas approaches the "wet" type. A possible gas reserve with a volume of 4,000,000,000 cu. m. (141,000,-000,000 cu. ft.) has been calculated, for an area of about 5 sq. km. of the Daszawa field, on the basis of production obtained and of decreases in pressure and their distribution. The fields of Roztoki and Strachocina (No. 12) have not yet supplied sufficient data for a calculation of reserves, which might possibly be estimated at 2,000,000,000 cu, m. (70,000,-000,000 cu. ft.).

Jan 1, 1937

By Raymond B. Ladoo

NONMETALLIC minerals (excluding fuels) arid their primary products produced annual in the United States have a value in excess of one billion dollars, or more than that of the metals, yet the lack of expert knowledge of some of the fundamental technical and economic aspects of this most important and complicated business is astonishing. This paper will deal with the economics of this non- metallic mineral field-the business of making money from producing these minerals. The incentive behind all business activity in a capitalistic economy is to make money-to plan so that each dollar invested in property, plant, equipment, services, and so on will return more than a dollar plus simple interest. Of course, business has social, civic, and national duties and responsibilities, but the fulfillment of these is largely dependent upon financial success.

Jan 1, 1939

By A. M. Gsudin, F. W. Bloecher, C. S. Chan-s, P. L. De Bruyn

M ANY elements can now be obtained in radioactive form. The radioisotopes have the same chemical properties as the corresponding inactive forms, differing from them only by their nuclear instability. This combination of properties permits radioelements to act as atomic tracers, the tracer atoms revealing themselves at the time of their decay with emission of electrons and positrons (beta radiation), helium nuclei (alpha radiation), or electromagnetic radiation (gamma radiation). The tracer technique is particularly attractive for the study of surface chemistry problems in general and flotation problems in particular because of its extreme sensitivity. A large proportion of the ionizing events, initiated by the characteristic decay emissions in a radioactive sample, can be recorded by radiation probes of suitable design and geometry. An idea of this sensitivity can be gathered from the following example: assume that 0.001 mg of pure RaD (radiolead), a beta-ray emitter, is used in a flota¬tion tracer experiment. This is 1210 X 10-1 mole; since the fraction trans¬formed per second (the so-called decay constant), is 9.92 X 10-10, the number of ionizing events per second would be (6.023 X 1023 X y,,, X 10-1) X 9.92 X 10-10 = 2.845 X 106. (The decay constant is expressed in sec-'. Its product with the half life, expressed in seconds, is the pure number, natural logarithm of 2 = 0.693. The half life is the length of time required for decay of one half of the total number of radioactive atoms of one particular type.) (See reference (1) at the end of this article.)

Jan 1, 1948

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

By William B. Plank

ENGINEERING students to the number of 73,269 had been enrolled in United States and Canadian schools on Nov. 5, 1945, but, as shown in the following tables, even this sizable number will not greatly remedy the 150,000 deficit reported by Vannevar Bush, director of the U. S. Office of Scientific Research and Development, to exist in the engineering and scientific man-power supply. These figures were received in advance from the Society for the Promotion of Engineering Education, and are given in detail in the January 1946 issue of the Journal of Engineering Education. Although the enrollment on Nov. 5 was an increase of 76% over the low of 41,632 in 1944-45, it was still 36% below the peak enrollment in 1941-42 of 115, 228. These figures include both undergraduate students and graduate students in the schools of the United States and Canada and are therefore comparable. As was to be expected, almost half of this enrollment is in the first or freshman year and 25% of the total are veterans. Also, 1,850, or about 2.5%, are women. A measure of the seriousness of the engineering graduate supply in these two countries is indicated by the trend of the number of first degrees that have been conferred during this period of scarcity:

Jan 1, 1946

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.' It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By W. L. Zeigler

The mill is a departure from gravity concentration and has gained a reputation for the low initial cost of erection, extreme simplicity and the low cost of milling on the refractory character of the ore which is treated. The structure is of heavy timbers with board walls and corrugated roofing. The floors are concrete and the general layout is of the ground floor only. All the machines are driven by individual motors and the transmission usually found in such a plant is entirely absent. (Fig. 2.) ORE The ore from the Galena mine is sheared Wallace quartzite replaced with quartz, siderite, pyrite, sphalerite, gray copper (tetrahedrite) and very fine-grained argentiferous galena. Much of the silver is undoubtedly associated with the gray copper, the amount, however, apparently varies with different localities in the vein. An average assay of the ore is 6.0 per cent. lead, 1.3 per cent. zinc, 0.3 per cent. copper, 17.5 per cent. iron and 4.5 oz. silver. The concentrates produced are of an average 53 per cent. lead, 40 oz. silver, 8 per cent. zinc and 11 per cent. iron, while the tailings are 0.5 per cent. lead, 0.4 oz. silver. With the present market for zinc no attempt is made to produce a zinc concentrate.

Jan 1, 1927

By C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury; have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. TABLE 1.-Lattice Constants and Twinning Law of the Be-Cd Group of Hexagonal Metals Dimensions of Unit Axial Cell, A Ratio Description of Twinning Element a° c° (c°/a°) Composition Axis Plane Beryllium 2.28(3) 3.60(7) 1.58 {1012} Probably 1 {1012} Magnesium 3.22 5.23 1.621 ,1 {1012} Zinc 2.65(7) 4.94(8 1.86(2) 11012 } 1 {1012) Cadmium 2.98 5.63 1.88(5) {1012} Probably 1 {1012} Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2. A determination of the composition

Jan 1, 1928

By John Dasher

Extrapolation is a useful technique, but it can be overdone. Seldom is it justified to study over a range of 1 to 6 and extrapolate the results to 150,000. It is especially dangerous if the extrapolation is based on a false assumption. The authors assume settlers scale-up by residence time rather than by area, admit their result (a settler depth of 7 m) is "unreasonable" and suggest longer, wider, shallower settlers might be better. Various authors have noted for a copper-LIX system a total flow basis of 2 gpm per sq ft for sizing settlers. The results of this are compared with those in the paper in [Table 7]. The authors note that flooding of their settlers was never approached. Thus the smallest unit calculated is understandably twice too big. The largest however, is 5% of the required size. I note that the figures in [Table 6] for 1/min/cm2 are based on plan area rather than cross section as titled and are wrong by l0 4. A flow of 2050 1/min/cm2 is about Mach I. It is also 10 5/3 or 46.5 times that of the little one, although the abstract says the design was based on constant flow rate per unit cross section.

Jan 1, 1977

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By M. R. Meyer, W. T. Walter

A great deal is known, in a qualitative sense, about the performance of CMI EB-36 centrifuges. The manufacturer can give reliable guidance for the proper operation of its centrifuges and can give general estimates of expected product moisture and recovery. Quantitative estimates of the effects of changes in the various operating parameters are more difficult to find. The engineer faced with designing a preparation plant may be without the specific data needed to make decisions. For example, to obtain optimum product moisture when drying 9.5 mm X 595 µm (0.4 in. x 28 mesh) coal the centrifuge manufacturer recommends having no more than 5% -595 µm (-28 mesh) material in the centrifuge feed. They know that more -595 µm (-28 mesh)material in the feed will cause higher product moistures, but they usually cannot quantify the increased moisture or describe the shape of the product moisture versus -595 µm (-28 mesh) in the feed curve. This study was conceived to provide quantitative information on the EB-36 centrifuges, focusing on product moisture, recovery, and size degradation. All of the centrifuges tested were Model EB-36 dryers from Centrifugal and Mechanical Industries Inc. (CMI), with feeds in the nominal 9.5 mm x 595 pm (0.4 in. x 28 mesh) range. These are typical centrifugal dryers in this application, and many were available for testing.

Jan 1, 1984

By AIME AIME

BY the end of 1943, the United States will be able to produce aluminum at a rate of 1,150,000 tons a year. How much aluminum is 1,150,000 tons? It is sufficient to replace every railroad passenger car in this country three times a year. Or, it would put a thirty-piece aluminum cooking utensil set in every one of America's 34,000,000 homes with enough metal left over to make 5,000,000 miles of aluminum transmission cable, such as was used in the electrification of much of rural America. Expansion of aluminum production capacity for the war program has occurred in three steps: (1) expansion by private industry; (2) the letting of contracts by the Defense Plant Corp. for the construction of additional aluminum plants which may remain after the war to compete with existing facilities; and (3) the more recently announced D.P.C. program for the building of emergency plants to make aluminum, using stand-by power available in large metropolitan centers power of relatively higher cost, making it questionable whether such plants, now gravely needed, will be able to compete in a peacetime economy.

Jan 1, 1943

By Philip J. Shenon

IN 1947 the mining industry strove desperately to regain operating normalcy. During the first part of the year the industry in this country was plagued with labor shortages, strikes, and portal-to-portal lawsuits. Then followed the uncertainty of Government policy with respect to subsidies and tariffs; and the long and bitter controversy as to whether we are a nation of mineral "haves" or "have-nots." As the year progressed the labor supply impoved somewhat and the Taft-Hartley law brought partial relief to strike-troubled industry. The uncertainty with respect to tariffs was partly answered by President Truman on April 29 when he announced the suspension of the 4¢ import duty on copper until March 31, 1949, and later, near the close of the year, by the announcement of the tariff agreement signed by the United Nations at Geneva. By this agreement tariff rates are to be adjusted downward, or "bound" at their present levels, for three years, on commodities amounting to some 60 per cent of United States trade. Effective Jan. 1, 1948 the rate of duty will be substantially reduced on ores, concentrates, or metals of zinc, aluminum, copper, manganese, tungsten, iron, steel, barytes, nickel, cadmium, and antimony.

Jan 1, 1948

By A. B. Kinzel

SILICON and its metallurgical uses have been the subject of speculation since the earliest days of modern civilization. The early philosophers, Theophrastus and Pliny, believed that silica was a special form of ice, an opinion that was not seriously challenged until the seventeenth century. The first comprehensive view of the nature of silica was advanced by Lavoisier in 1787. He assumed silica to be an oxide of an unknown metal. In 1808 Berzelius produced ferrosilicon by heating silica, iron and charcoal. Probably the first produc¬tion of crystallized silicon was in 1854 when H. St. C. Deville accidentally produced the material while electrolyzing a double chloride of aluminum and sodium containing siliceous impurities. It is not strange that the early investigators should have given so much attention to silica and silicon, because of the great natural abundance of the former. Although silicon does not exist in the elemental state in nature, it has been estimated that the lithosphere contains approximately 60 per cent silica; quartz and rock crystal are found in practically every part of the world.

Jan 1, 1933

By Thomas T., Read

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others ' in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would , require too much space. The remainder of this discussion, there- fore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. Geology The first, from the historical view, is geology in its relation to the mineral industries. Previous, chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering, so overlapped one another that men who were by training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in- geology as a pure science, and who perhaps took a doctor's .degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would not be questioned, even though 'they did not .take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

By George A. Roche

Investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria used to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of investment strategy for two of the three mutual funds sponsored by the Price organization and for its private clients. However, during the past five years inflation has accelerated due to a variety of factors including the inability of government to meet seemingly unlimited needs with limited revenue sources.

Jan 4, 1972

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

By W. W. Simpson, W. L. Staker, R. G. Sandberg

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 17 kg NaCN/t of solution (0.34 lb NaCN/st). Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0.5-2.9 kg CaS/kg Hg (0.5-2.9 lb/lb) in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1985

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986