Search Documents

By J. Grosso, D. J. Nagel

In many metallurgical studies, it is necessary to reveal the composition and structural properties of materials. Usually this is done by etching, but some substances do not etch well or easily. Anodizing is known to provide an alternate treatment in many cases. In general, this technique is simple, often more sensitive to composition differences than etching, has excellent resolution, and provides variable contrast in those elements and alloys which anodize. Here we report the use of anodizing in diffusion studies in the TiCb system. Fig. 1 shows a cross section of the diffusion zone in a TiCb couple. The anodizing has clearly revealed both composition and crystallographic features. The maximum bulk penetration of the titanium into the columbium is marked by a sharp line because of the steep concentration gradient. The titanium grain size and orientation differences are also evident. Variation in the grain size reflects the gradually decreasing columbium concentration.

Jan 1, 1967

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By K. Osseo-Asare

The presence of carbonaceous matter in gold ores presents a two-fold problem: (1) The poor release of gold from the carbonaceous matrix and (2) the uptake of dissolved gold by the carbonaceous leach residues. A critical review is presented of the published information from various parts of the world pertaining to the nature of the carbon-containing components of these ores and their different roles in the gold extraction process. Included in this paper are new results based on the authors' research on carbonaceous ores from the Prestea goldfields of Ghana. Methods for isolating and characterizing the carbon-containing materials are given and a discussion is presented of the interaction of the carbonaceous ores as well as the fractionated components with aurocyanide solutions. Emphasis is on basic physico-chemical phenomena, investigated with the aid of X-ray diffraction, infrared spectroscopy, adsorption, and electrophoretic mobility studies.

Jan 1, 1984

By F. J. Escandon V.

The Plomosas stratiform lead and zinc deposits are located in northeastern Chihuahua in a sequence of folded Paleozoic and Jurassic rocks. They consist mainly of channel or blanket-like bodies of ellipsoidal cross section restricted to a 60-in-thick shaly limestone and a 30-m-thick marble horizon of La Casita formation, with some reemplacement veins and shoots within the Plomosas formation. The mineralogy consists of iron-poor sphalerite, galena with a small silver content, and pyrite, in a gangue of calcite, barite, and minor quartz. The ore bodies present a lateral zoning with zinc-lead ratios increasing to the northwest. Vertical zoning shows marked changes in zinc-lead ratios and in the width and tenor of the ore which cannot be related to sedimentary or diagenetic features. Transgressive mineralization and some small fissure veins and breccia pipes also point to an epigenetic origin. Sulfur isotope analysis and geochemical data indicate hydrothermal solutions. Texture of the ores in the Mina Vieja marble is coarse, but in the Cuesta shale it is banded along bedding. The low iron and silver content of the sphalerite and galena and the weak hydrothermal alteration (only marbleization) of the wall rock suggest a telethermal stage of the solutions. There is no evidence of a possible intrusive rock mineralization.

Jan 1, 1976

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By Fred K. Stieler

The largest updraft sinter machine built has a roasting area of 132 sq.m. Sinter machines with an area of over 200 sq.m. are under consideration. These large machines require new techniques with regard to drive thrust and sealing mechanism. To optimize the results of sinter plants, the charge preparation systems and the return fines circuits were improved. Special crushers were developed for crushing return sinter of up to 800 ºC to a size of minus 6 mm. Strand cooling of Pb-sinter was investigated. Different methods for plant ventilation were compared. New processes, which might replace sintering in the future, are in the stage of large - scale testing.

Jan 1, 1977

By S. Whinery

In these times of sharp rivalry, both as to price and quality, among the makers and venders of engineering explosives, it is often desirable to be able to determine the relative energy or value of the various explosives offered for sale, in order to purchase intelligently ; or, having contracted for a large amount of an explosive of a certain standard quality, to be able to ascertain if the manufacturer keeps his product up to the specified standard. The simple and inexpensive apparatus described below was devised by the writer while engaged on the improvement of the Tennessee River, at MuscleShoals, under the direction of' Major W. R. King, U. S. Engineers, in the summer of 1879. It answered the purpose so well that it is thought that a brief account of it may be of interest to other engineers. It consisted, essentially, of an old blacksmith's anvil and a common striking hammer, such as is used for driving rock-drills. The anvil was placed face downward on solid, level ground. In what was then the top of it, a vertical hole, one and one-fourth inch in diameter and about one arid three-fourths inch deep, was made with a ratchetdrill. The surface of the anvil immediately around the drill-hole was made as true and smooth as possible with a file. Next, a new striking-hammer, weighing nine pounds, with a turned and true face, was selected ; and a handle, eleven feet long and about one and a half inches in diameter, was fitted into it so that it

Jan 1, 1886

By A. H. Daane, R. L. Myklebust

The yttrium-manganese system has been investigated by thermal, metallographic, and X-ray diffraction methods. There are three intermetallic compounds present: YMn2 which melts congruently, YMn4, which undergoes syntectic decomposition, and YMn,, which undergoes peritectic decomposition. The compound YMn4 is ferromagnetic at room temperature with a Curie temperature of 214°C. There are eutectics at 25.2, 60.9, and 82.0 wt pct Mn which melt at 878°, 1100°, and 1075°C, respectively. Crys-tallographic data are given for YMn4, and YMn12 . The terminal solid solubilities are low. In a general program of study of yttrium metal in this laboratory some alloy systems of this metal with elements of the first transition period have been examined. This work was originally instigated by experiences in cladding yttrium with jackets of some protective metals such as Inconel for high-temperature service in air.' In some cases a low-melting phase was observed to form between the Inconel and the yttrium resulting in failure of the samples. In characterizing this reaction, a survey was made of the systems of yttrium with chromium, manganese, iron and nickel,, and it was found that a eutectic was formed between these metals and yttrium on the yttrium-rich side of the system. This present study of the Y-Mn system was carried out to examine in more detail the alloying nature of yttrium, and to correlate trends that have been observed in previous related studies. It was observed by Voge13 that in the systems of lanthanum, cerium, and praseodymium with each of the metals in the first transition series, the tendency to form compounds diminished in the order nickel, cobalt, and iron while no compounds were formed with manganese, chromium, or titanium. Beaudry and Daane4 observed a similar behavior in the systems of yttrium with some members of the first transition series except that the tendency for compound formation was greater. Both the Y-Ti5 and Y-Cra systems consist of simple eutectics, while in the Y-Fe,7 Y-CO, and Y-Ni4 systems, there are four, eight, and nine compounds, respectively. In addition to the above trends, the similar atomic radii and electronegativities of yttrium and thorium invite a comparison between their alloying behaviors with a common element such as manganese. In crys- tallographic studies, Florio et al.' have identified three intermediate phases in this system which are ThMn2, Th6Mn23, and ThMn,,. Gschneidner and Waber10 have examined published information on alloy systems of the rare-earth metals and have correlated this information with current alloying theory. From their study, they predicted that the Y-Mn system would contain one intermetallic compound. On the basis of this prediction, the trend in the alloying behavior of yttrium with the elements of the first transition series and the alloying behavior of thorium with manganese, one might expect from one to three intermetallic compounds to form in the Y-Mn system. A consideration of Hume-Rothery's rules of alloying based on size-factor, electronegativity, and valency suggested a small terminal solubility and possible compound formation. The present study was undertaken to confirm these predictions of low terminal solid solubility and compound formation and to establish the general alloying behavior of yttrium with manganese. EXPERIMENTAL Materials. The manganese used in this investigation was obtained from the Foote Mineral Co. as electrolytic plates of 99.9 pct stated purity; the yttrium metal was prepared in this laboratory. Table I gives the analyses of these materials. For the solubility studies at the yttrium-rich end of the alloy system, distilled yttrium, whose major impurity was 200 ppm Ti, was used. Preparation of Alloys. The alloys were formed by comelting the two metals in an are-melting furnace under an atmosphere of argon. The buttons thus formed were inverted and remelted three to five times to promote homogeneity. Due to the high vapor pressure of manganese, it was assumed that the weight lost during are-melting was all manganese. This assumption was based on the very good agreement observed between calculated compositions and chemical analyses of several alloys. The compositions of the dilute alloys used for solid solu-

Jan 1, 1962

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the ' alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The-Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend .a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and. assurance is given that most careful service will be rendered to them.

Jan 6, 1915

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine miles across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40° to 45° southeast.

Jan 1, 1873

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable-shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 2, 1914

By William Laird

The predominent method of coal mining in the United States for years has been room-and-pillar mining. The reason for this has been the advantages of room-and- pillar method which is a relatively flexible system and its capital investment. The room-and-pillar method permits some selectivity in mining, especially where gas wells, faults and possible coal quality may be a factor. The mobility of continuous and conventional mining equipment used to develop entries may also be used for retreat mining of rooms and pillars. Longwall mining of coal takes place along a long straight face, or wall, blocked out between two butt or panel entries. The long faces or walls are normally projected in lengths of 61 to 183 m (200 to 600 ft) in this country. The longwall method of mining had its beginning in the United States during the 1800's. During that period, pack wall and wood posts were used for roof support. The longwall face was mined by miners using picks to undercut the coal. To keep the coal face from turning over, short wood posts called sprags were set in a slant position as the coal face was undercut to the depth of two to three feet. When the under-cutting cycle was completed, the sprags were removed to permit the coal to fall from the roof pressure. The longwall mining of coal did not take a firm hold during the 18009s, and room-and-pillar prevailed. In the early 19009s, steel jacks were introduced, and along with it, the modified caving theory. In March of 1950, a retreat longwall mining system, utilizing a plow, manually operated props, wood cribs and chock releases, was installed in one of Eastern Associated Coal Corp.'s mines.

Jan 1, 1981

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By P. E. Senseny

INTRODUCTION Massive hydraulic fractures have been used since 1949 in the petroleum industry to enhance production rates and increase recoverable reserves. Currently, a research program, the Multi-Well Experiment, is underway to develop the understanding and technology to a1 low economic production of the large gas reserves of the low permeability, lenticular sandstone formations in the western U.S. (Atkinson, et al, 1981; Northrop and Sattler, 1983). Use of state- of-the-art hydraulic fracturing techniques is a part of this investigation. As a portion of an extensive core program in support of this experiment (Sattler, 1983), fracture toughness has been determined for 56 sandstone, shale, mudstone, or siltstone horizons from three wells in the Piceance Basin. The role of fracture toughness in hydraulic fracturing is not well understood because other factors, such as in situ stress, dominate fracture geometry and containment. Rubin (1983) concluded from analysis of his laboratory hydrofracture experiments that fracture toughness should be included in design and numerical simulation of hydraulic fractures. However, van Eekelen (1982) contends that the stress intensity at the crack front should be so much greater than the fracture toughness of the rock that toughness can have no importance. Generally, fracture toughness and other material properties, such as elastic moduli and permeability, are thought to be of secondary importance in determining fracture geometry and containment. In spite of this, there is a need to acquire a more quantitative understanding of their importance for accurate design and simulation calculations. Analysis of fracture geometry and containment data from hydraulic fracturing experiments carried out in formations where fracture toughness and other rock properties are

Jan 1, 1984

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.' In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By John E. Sweet

THERE have already been so many subjects of a purely mechanical nature presented to the Institute of Mining Engineers, that it is unnecessary for me to apologize for adding another to the list. When a new invention, or what is supposed to be a new invention, claiming simply an improvement on the well-known devices, is to be described, it is usual to point out the defects of the old and give a history of the object or the art up to date. But, as no doubt a large proportion of the members of this Institute know as much, or more, about the history and use of the steam-engine indicator than I do myself, I will not further preface the subject, than to remind you that what called for the Richards's improvement on the Watt's indicator was high speed ; that the leading improvement was the reduction of momentum in the reciprocating parts; and that this was accomplished by making the parts lighter, and reducing the travel of the heaviest of them, and consequently the speed and momentum. The use of the indicator has been extended, for the speed of steam-engines and other prime movers has been increased, until one engineer at least, John Cooper, of Philadelphia, says, "I want an indicator that will work up to a thousand revolutions." Mr. Thompson, of the Buckeye Steam-Engine Company, of Salem, Ohio, has improved on the Richards's indicator by another reduction in the momentum, which is done by putting the parallel motion nearer the fulcrum of the pencil arm, reducing both weight and travel. The characteristic feature of the indicator I am going to illustrate is a still further reduction in the same direction, which is accomplished by dispensing with the parallel motion altogether. As is often the, case, in putting a simple idea into shape, some difficulties

Jan 1, 1879

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine milt",3 across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40' to 45' southeast