Search Documents

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By M. A. Scheil

Austenitic stainless alloys are susceptible to stress-corrosion cracking which may occur under certain corrosion environments irrespective of their susceptibility to intergranular corrosion. Test samples are described for investigating stress-corrosion susceptibility of alloys for industrial equipment. A laboratory test using a solution of magnesium chloride boiling at 309 F. was found to produce transgranular cracks in several alloys investigated and in types 347 and 316 stainless steel tubing a residual stress of the order of 10,000 psi. was observed to initiate cracking. The susceptibility to stress-corrosion cracking as judged by the boiling magnesium chloride test indicates that alloys may be selected which will withstand a high stress in service Stressed specimens of stainless alloys included in a corrosion testing program will aid in determining the acceptibility of these fabricated alloys, when stressed, to the service conditions.

Jan 1, 1945

By W. C. Knopf, I. M. LeBaron

In the Carlsbad area potash is dry-mined and wet-concentrated. Wet concentration involves recircu-lation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KCl. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report. Potash ores available in this country are largely mixtures of halite and sylvite contaminated with slimes and often with many sulfate and magnesium minerals. Electrostatic concentration of KCl when the contaminating minerals are in low percentage has been accomplished. Continuous production of better than 60 pct K2O concentrate from high potassium sulfate ores has not been demonstrated at the present time. Laboratory Procedure: Laboratory work on electrostatic beneficiation of potash minerals has been carried out using both pure crystals and mined ore. Electrostatic separation of the two main components of potash ore, sylvite (KCl) and halite (NaCl), is accomplished by first heat-treating the ore to allow for electric charging of the particles. Preferential exchange of' electrical charges between different mineral particles through surface contact is the principal mechanism involved. After proper conditioning of the particle surfaces, the oppositely charged minerals are dropped vertically into a horizontal electric field having a field gradient from about 5000 to 15,000 v per in. The particles are free-falling in the field. A suitable power supply is used to produce the proper total voltage for the electric field. Total required voltage is, of course, a function of electrode spacing. A typical electrode arrangement with power supply is shown in Fig. 1. In general, the total voltage on any system is 75,000 to 90,000 v. Power consumption is negligible, as leakage at insulators and corona discharge are the main losses in the system. Optimum preheat temperatures for pure material components generally are not the same as for mined minerals. Fig. 2 shows clearly that maximum recovery on a 50 pct pure KCl, 50 pct pure NaCl mixture occurs at a preheat temperature of about 600°F. In this test the preheat mixture was allowed to cool to about 225°F before dropping through the electric field. The optimum temperature for sep- aration is practically never the optimum temperature of preheat. Optimum separation for mined Carlsbad potash ores occurs when a preheat temperature closer to 900°F is used, as shown by Fig. 3, which plots percent sylvite (KCl) in the concentrate and tails as a function of preheat temperatures. Here again the ore was allowed to cool to about 225°F before separation. It should be noted that efficiency of separation increases continuously with increasing preheat temperatures until incipient fusion of the ore takes place at about 950°F. The increase in optimum preheat temperature for Carlsbad ores over the pure minerals can be traced to the effect of the clay slimes intimately associated with the mined potash. If the slimes associated with the ore are removed by washing with alcohol or other non-aqueous material, the necessity of preheating to the high temperature is removed. This temperature range has been proved critical within these limits during continuous pilot plant operation. Concentrate and tailings grade and optimum recovery also are functions of the temperature of the potash mineral particles during separation in the electric field. Fig. 4 presents data indicating that feed to the rougher pass should range between 150°F and 275°F for best results. It has been found by subsequent pilot plant work that these temperatures can be maintained in actual operation.

Jan 1, 1959

By F. Pošepný

Part I.—General Facts and Theories. PAGE 1. Systems of Classification Employed Hitherto, . . 199 2. Standpoint and View of the Present Paper, . . . 206 3. The Xenogenites in General, ...207 4. The Subterranean Water-Oirculation, . . . 212 A. The Vadose Underground Circulation, . . . 213 Filling of Open Spaces Formed by Vadose Circulation, . . 217 B. The Deep Underground Circulation, . 220 Ascending Waters Encountered in Mines, , 222 Related Phenomena near the Surface, . 225 Mineral Springs at the Surface,. . 230 Chemical Constitution of Mineral Waters, . 232 Minute Metallic Admixtures in Mineral Waters, . . . 238 Alterations Produced by Mineral Springs, . 240 Structural Features of the Deposits of Mineral Springs, . . 244 5. Origin of Ore-Deposits in the Deep Region, . . . 247 Manner of Filling of Open Spaces in General, . . . 254 Part II.—Examples or Classes of Deposits. 1. Ore-Deposits in Spaces of Discission, .. 264 General Features and Illustrations, a. Ore-Veins in Stratified Rocks, .. 269 Clausthal, 269; Andreasberg, 270. b. Ore-veins in the Neighborhood of Eruptive Masses, 271 The Erzgebirge, 271; Przibram, 272. c. Ore-Veins Wholly Within Large Eruptive Formations, 274 Hungary, 274; Dacian Gold-field. 275; Verespatak, 276; Vulkoj, 276 ; Comstock lode, 278.

Jan 1, 1894

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in. the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By Richard O. Carlson

Ions of p31 and B 11 were implanted in natural insulating diamond macles. The thin (-0.4µ) layers showed sheet resistances of 107 to 1011 ohm per sq and activation energies of 0.17 to 0.34 ev above room temperature. However, no Hall effect could be measured, indicating that mobilities were less than I to 10 sq cm per (v-sec). Such low mobilities may be due to excessive scattering due to radiation damage in the bombarded layer or to very high concentrations of active compensating impurities. Annealing did not materially change the room -temperature properties, but the temperature was limited to -800°C by surface graphitization, the latter process probably being accelerated by lattice damage in our diamonds arising from the ion bombardment. A weak n-type thermoelectric power was detected after p31 irradiation, but it cannot be presumed that we have made the phosphorus ions active as donors in diamond. The natural diamonds have a high and uncontrolled concentration of impurities and, when coupled with the radiation damage and graphitization problems, would appear to seriously limit the quality of semiconductor that we can presently achieve by ion implantation in diamond. ALTHOUGH diamonds are usually thought of as insulating in terms of their electrical conductivity, it was found about 15 years ago that natural semiconducting diamonds do occur rarely, and these were designated as type IIb diamonds. These p-type semiconducting diamonds were found to be dominated by an impurity level 0.37 ev from the valence band. Evidence today based on correlation of the concentration of acceptor states from Hall effect measurements with the impurity concentrations determined by neutron activation analysis point to aluminum as the dominant acceptor impurity.' The compensating donor is believed to be nitrogen, which has a donor level 1.6 ev above the valence band.' However, only a small fraction of the total nitrogen content in the diamond is electrically active. An infrared absorption band at 7.8 p and ultraviolet absorption near 4 ev have been associated with nitrogen, the former providing a quantitative measure of nitrogen content.3 The nitrogen content is -l020 cm-3 in insulating or type I diamonds, but is less than 10'' in natural semiconducting diamonds. Much of this nitrogen is distributed in platelets oriented in (100) planes and not atomically dispersed in the diamond lattice.4 Semiconducting diamonds have been deliberately formed by incorporating impurities into the graphite charge in the high-pressure apparatus used to form diamonds.5 These manufactured semiconducting diamonds are always p-type, and while some show the 0.37 ev level due to aluminum, most such samples have been ascribed to impurity banding effects.6 The best natural or manufactured semiconducting diamonds have hole mobilities near 1500 sq cm per (v-sec) at room temperature, and those with the 0.37-ev level can be analyzed to reveal an acceptor concentration of 3 to 8 X 1016 cm-3 and a donor concentration 3 to 10 times lower.' NO bulk n-type diamonds have ever been reported, but the electron mobility has been measured as 1900 sq cm per (v-sec) by irradiating a diamond with ultraviolet to excite electrons out of the deep nitrogen donor level or other levels.7 New hope for the formation of n-type diamond has emerged from the ion-implantation method whereby desired impurities are introduced into a crystal lattice by bombardment with a high-energy beam of the impurity ion. It was found in the case of silicon that the usual donors such as phosphorus and arsenic and acceptors such as boron and gallium could be implanted into silicon. Wentorf and arrow' produced semiconducting layers on diamonds by an ionic bombardment in a glow discharge at potentials of about 2 kv. The observed typeness from thermoelectric probing seemed to depend on the atmosphere gas (nitrogen, argon, or hydrogen) rather than on the electrode material, but the nature of the conduction process in the thin damaged surface layer is completely unknown. A Russian group under Vavilov has attempted high-energy ion implantation in natural diamonds using boron and lithium ions9 and later also phosphorus, aluminum, and carbon ions.10 Their papers claim n-type layers from lithium, phosphorus, and carbon implant and a p-type layer from boron and aluminum implant, though the methods of type determination are not described in detail. Under government contract support, the Ion Physics Corp. has studied ion implantation in several semiconductors. While the bulk of their study1' was devoted to the irradiation of silicon, they did carry out a short study on boron and phosphorus implantation into natural diamonds. They did observe surface conducting layers but did not determine the typeness of the layers. For our experiments, phosphorus and boron were chosen as the dopant ions because of their respective donor and acceptor behavior in germanium and silicon. Moreover, they are the lightest mass dopants of the shallow level donors and acceptors from columns 111 and V of the Periodic Table (excluding nitrogen which is already present in diamond), and will have the largest depth penetration into the diamond lattice. EXPERIMENTAL Diamonds. As the target diamonds for our ion implantation study, we chose commercially available macles, which are flat, twinned diamond crystals. By scanning through the stock of a wholesale distributor

Jan 1, 1970

By M. S. Seltzer

High temperature steady-state creep rates have been determined jor lead sulfide single crystals whose defect concentrations were fixed by equilibration under controlled sulfur pressure. The activation energy of creep, Qc , for undoped lead sulfide, is a function 01 composilion, decreasing from 2.9 to 2.2 ev as the carrier concentration increases from 9 x 1016 to 8 1018 electrons cm-3 for lead excess crystals, and increasing from 1.7 to 2.3 ev as the concentration of holes increases from 4 x 1017 to 1 x 1018 cm-3 in sulfur excess material. For five different composilions, Qc for undoped and bismuth-doped crystals has been found to be equal to Qpb + Qs, the self-diffusion activation energies for lead and sulfur in PbS. It is well-established1 that high-temperature steady-state creep of pure metals is a diffusion-controlled process, where the activation energy of creep is equal, within experimental error, to the activation energy of self-diffusion. The relationship between the activation energy for steady-state creep and those for self-diffusion in binary compounds is more complicated, however, because two different diffusing species must be considered, and becayse the activation energies may be influenced by compositional variations and by foreign atom additions.2-4 In some cases experimentally determined creep activation energies are correlated with those for self-diffusion of the slower-moving species, but such agreement is by no means universal. Interpretation of experimental results is difficult because few investigations include measurements of creep rates and self-diffusion coefficients of both diffusing species on single crystals of similar composition and foreign atom concentration. The objective of this investigation, therefore, is to determine the influence of stoichiometric defects and foreign atoms on steady-state creep and self-diffusion for a well-characterized binary compound. Lead sulfide, a compound semiconductor which crystallizes in the NaC1-type structure, and whose homogeneity range includes compositions on either side of the 1:l atom ratio, was chosen for study in this investigation. The pressure-temperature-composition relations for PbS are available,5,3 and deviations from stoichiometry may be monitored by electrical measurements.7 Single-crystal specimens are available to allow observation of effects due to bulk phenomena without interference from grain-boundary effects. These crystals have been employed to determine steady-state creep rates under compressive stress for "pure" and bismuth-doped PbS as a function of sulfur pressure and temperature as well as crystal orientation and applied stress in order to establish the relationships between defect concentrations and creep rates. EXPERIMENTAL PROCEDURES Crystal Growth. Lead sulfide crystals, prepared by the Bridgman method, are grown in evacuated quartz crucibles, filled with almost equal atomic proportions of high-purity (99.999 pct) lead and sulfur, and heated to a temperature above the melting point of PbS (about 1127°C) so that the lead and sulfur react to form molten PbS. The crucible and melt are dropped through the hot zone of the crystal-growing furnace at the rate of 1 cm per hr. The maximum melting point of PbS is slightly on the lead-rich side of the 50:50 composition; hence crystals grown from a near stoichiometric melt are usually n-type semiconductors containing excess lead atoms. Typically the lead excess concentration in solid solution with the PbS is 3 x 1018 atoms cm-3. Crystals containing either 1/20 or 1/2 mole pct Bi2S3 were prepared by addition of the foreign atoms prior to crystal synthesis. Preparation of Specimens of Controlled Stoichiom-etry. Since it is difficult to grow crystals of desired composition, the process of crystal growth and control of stoichiometry are separated into two distinct operations. Equilibration of as-grown PbS to a desired composition is most easily accomplished by first annealing the n-type crystals under high sulfur pressure (about 1 atm) at temperatures above 700°C. This process serves to put excess lead precipitates into solution, yielding 0 -type crystals upon quenching to room temperature. Inter diffusion occurs readily in crystals so treated, and the methods described by Bloem may then be employed to obtain crystals of controlled stoi-chiometry. For the creep measurements made in this study, this involves heating crystals in mixtures of H2 and H2S The equilibrium constant for H2S is given by: Thus the sulfur partial pressure is obtained from knowledge of the H2/H2S ratio and Kh2S for the temperature in question. Fig. 1 shows the p-T-x diagram for PbS. It can be seen that, within the stability limits for single-phase lead sulfide, desired compositions may be obtained by equilibrating under a specified sulfur pressure and temperature. Characterization of Crystals. The principal methods for evaluating PbS crystals include measurement of electrical properties and mass-spectrographic analysis. The measured electrical parameters include Hall coefficient, conductivity type, and electrical resistivity Bloem7 has shown that there is a 1:l relation between the defect concentration and carrier concentration obtained. Hence, if the contribution to the carrier con-

Jan 1, 1968

By M. A. Childers

Recent work with controlled laboratory tests.' field experience and a new analytical approach indicate that casing centralization, pipe movement and relative rheological properties between the mud and cement (yield point and density) are the three controlling factors in successfu1 primary cementing of dual casing. Turbulent flow has been demonstrated to be unnecessary under the severe displace ment conditions of parallel dual strings of casing. Simultaneous reciprocation of dual casing in directionally drilled boreholes is highly dependent on centralization and on the rapid initiation of pipe movement once the casing has been run to total depth. Successful cementing of 30 out of 32 dual, 3%-in casing wells substantiated these conclusions. A review of 15 dual, 3 1/2-in. casing wells completed prior to the adoption of these principles disclosed only one success. Mathematical and graphical techniques permit the engineer to analyze and anticipate the success or failure of a cementing operation. Standoff, mud displacement and reciprocation can be analyzed mathematically and planned in deep, directional or straight boreholes by review of annular geometry, relative rheological properties between the mud and cement, and forces caused by caring weight, functional drag and differential sticking. Introduction The objective in primary cementing is to displace the drilling fluid with cement that will bond to the formation and casing to prevent communication through the annulus. The predominant cause of failure appears to be channels of gelled mud that remain in the annulus after cementing.1 '* Past investigations have noted many procedures that could improve the displacement process.2-' These procedures include centralization, chemical preflushes, mechanical mud cake removers, controlled flow rates in certain regimes, pipe movement an1 control of mud and cement properties. Not until recently have the effects of many of these procedures been isolated so that their individual importance could be determined. In a recent paper,' a comprehensive and analytical laboratory study of various factors controlling the displacement process concluded that there are three major factors in obtaining complete mud displacement by the cement slurry. 1. Good relative rheological properties between the mud and cement. The cement should be heavier and have a yield point and plastic viscosity higher than the mud being displaced. Buoyancy forces often can dominate the displacement process. 2. High degree of standoff or centralization. The more centered the casing, the greater the likelihood of complete mud displacement and removal. 3. Pipe movement obtained by rotation or reciprocation. Often unfavorable rheological properties between the mud and cement, and poor standoff can be compensated by pipe movement. This work demonstrates the compatibility of the latter concepts with field results extended to the more severe dual casing displacement process. Early Experience With Dual 3'/t-In. Primary Cementing Early slim casing completions in the West Delta Block 73 field, offshore Louisiana, included 17 dual 3%-in., 3 single 3% -in. and 1 dual 2% -in. casing installations. Table I provides data on these earlier wells. Usually, common Class A cement was placed across the pay zone and 12 percent gel cement was placed to a height of 500 ft above the highest productive sand. Centralizers (6%-in. OD maximum expansion) were placed two or three per joint on both casing strings from total depth through the completion intervals and at least one per joint for the remainder of the cement sheath. A number of techniques and procedures were attempted to improve cementing success. Casing was run simultaneously or separately with a number of mud conditioning and circulating techniques. Mechanical aids such as cement bonders, slmiding sleeves, turbulizers and various sizes and strengths of centralizers were used. Common and gel cements were mixed with fresh or sea water with a number of different additives to control retardation and dispersion. Cements were thinned and mixed at high rates to try to induce turbulent flow in the annulus. On one well the "slow flow" method was used." Perforating was accomplished with a jet orienting gun. Unsuccessful cement jobs were indicated by production of extraneous fluids or by pressure communication between zones. On test, five wells flowed water, four flowed sand and six had pressure communication with the other string or the 10%-in. casing. A total of 25 remedial squeeze ce-

Jan 1, 1969

By V. R. Garfias

INTRODUCTION FOR a number of years the senior author has been interested in the various geologic and engineering problems involved in the development of the petroliferous districts of northeastern Mexico, having in a previous paper 1 endeavored to present a summarized statement of the information relating to the geology and soil resources of this region. Of the many interesting geologic phenomena, perhaps those which have been the object of more speculation relate to the igneous intrusions which, in places, have a controlling influence on the accumulation of oil in commercial quantities, a relationship which has been tentatively explained by various observers with as many interestingly different views. The authors of the present paper aim to record, in the course of a general discussion of the various viewpoints, some additional data, and present further tentative conclusions with a view to rounding out an up-to-date summary of the subject. The greater part of the area in question lies in the State of Vera Cruz, only a northwest fraction being in the State of San Luis Potosi. Vera Cruz is bounded on the north by the State of Tamaulipas, the northernmost of the Mexican States along the Gulf. The topography of the States of Tamaulipas and Vera Cruz and of Texas and Louisiana to the north, is controlled by the Gulf coastal plain which in northern Vera Cruz has an average width of about 60 miles, the transitional topography between that of the rugged flanks of the Sierra and the lowlands of the coast being made up of a series of terraces and irregular hills and valleys.

Jan 8, 1917

By Leonard Greenburg, William B. Harris, Gustäv Werner

HAULAGE in tunneling operations generally has been done with electric locomotives. As a rule, on short hauls the source of electricity is a storage battery mounted on the locomotive, which, of course, must be removed and recharged periodically. Where the distance from the recharging point to the tunnel face is very long, and where loads are heavy, trolley-driven locomotives are used. Diesel engines have been used in mining and tunneling operations in Europe for a number of years. The recent reports of studies in Belgium1 and by the Bureau of Mines in this country2-4 have indicated the potentialities of this form of power for haulage, mucking, bulldozing and many other underground operations. The hazards attending the use of Diesel engines in more or less closed spaces have long been known. The exhaust constituents that may create a harmful or objectionable environment are carbon monoxide, oxides of nitrogen and sulphur, carbon dioxide, aldehydes and smoke. Lack of precise information regarding the concentration of these gases and the ventilation requirements to reduce them to safe levels has to some extent suppressed their general acceptance in tunneling and mining work. Not until the work of the Bureau of Mines referred to above, and certain experience gained in the construction of the Delaware Aqueduct,‡ has there been available the requisite information regarding the conditions under which their use may be permitted. This paper concerns itself with the successful operation of Diesel engines underground in the construction of certain parts of the Delaware Aqueduct, and describes the conditions under which Diesel engines have been found to operate with a minimum production of noxious gases. The test data reported were obtained during the operation of Diesel engines over a period of two years.* STUDIES BY THE NEW YORK STATE DEPARTMENT OF LABOR Exhaustive tests were made by the Division of Industrial Hygiene, of the composition of the exhaust gases given off by a Diesel engine mounted on. a test block. These tests showed that certain quantities of the gases are discharged from the exhaust. On the basis of these figures, preliminary requirements of design and control

Jan 1, 1942

By L. B. Slichter

After statement of the principles of similitude which apply to electromagnetic modeling, charts showing the inductive response of conducting spheres as dependent upon frequency, conductivity, and size are exhibited in this paper. The shape of the curve which relates intensity of response to frequency is significant in indicating the advisability of low frequencies in the exploration for conducting bodies, when consistent with the securing of a large percentage of the ideally possible response. Comparisons of theoretical response and that observed with models are shown, and relationships with the subject of applied electromagnetic prospecting are indicated. Maxwell Field Equations The Maxwell field equations summarize the physical laws that govern electrical field phenomena; they are the basis for the solution of electromagnetic problems. These concise equations, with adequately formulated boundary conditions, specify the complete electrical condition of continuous media, and the development of their solution amounts merely to a more convenient re-expression of phenomena already completely described. Thus, the immediate content of the field equations themselves is sufficient and sometimes convenient for the treating of certain questions (such as those relating to electromagnetic models) which are independent of the special factors of geometry, or the nature of an impressed field. The four Maxwell field equations are written below, in c.g.s. gaussian units: curl E = -B/c [21 div eE = 4pp [31 div B = 0 [41

Jan 1, 1932

The following is an incomplete list of members and guests who called at Institute headquarters during. the period Mar. 10, 1919,. to Apr. 10, 1919. F. T. Agthe, Hannibal, Mo. Jay Lonergan,. Denver, Colo. W. F. Almy, Canada. R. R. London, Cebu, P. I. P. G. Bandy, Mexico. W. D. Mainwaring, Philadelphia, Pa. H. R. Bank, Humboldt, Ariz. _ W. G. Mitchell, Montreal, Can. Alan M. Bateman, New Haven, Conn. Francis Nicholson, Joplin, Mo. C. A. Brooks, Lead, S. Dak: C. H. Palmer, Los Angeles, Calif. Louis J. Brunel, Oakland, Calif. D. A. Powell, Columbus, Ohio. W. Burns, Sante Fe, N. M. W. H. Reber, Dallas, Tex. J. B. Carlock, Major, 1st Gas Regt. Capt. J. B. Richards, Spokane, Wash. Louis S. Cates, Hayden, Ariz. T. C. Roberts, E. Orange, N. J. W. M. Corse, Mansfield, Ohio Max Roesler, Washington, D. C. E. 0. Daue, Philadelphia, Pa. C. 0. Sanford, Los-Angeles, Calif. John Davenport, W. Norfolk, Va. Gustave Sessinghaus, Denver, Colo. James T. Dixon, London, England, . E. H. Shriver, Milford Center, Ohio. S. K. Dahl, Messina, Transvaal, S. Af. H. M. Spoor. W. G. Eberhardt, Tucson, Ariz. W. H. Staver, New York. H. S. Emlaw, Grant Haven, Mich. D. B. Sterrett, Washington, D. C. I. W. Farrand, Camp Merritt. W. G. Swart, Duluth, Minn. Oscar Gotsch, Jr., St. Louis, Mo. A. W. Stickney, London, England. James 0. Greenan, Oakland, Calif. E. C. Templeton, Downey, Calif. Gilbert Hart, Philadelphia, Pa. . . R. T. Walker, Pioche, Nev. K. L. Hsueh, China. A. T. Ward, Bellefonte, Pa. Zay Jeffries, Cleveland, Ohio. Joel H. Watkins, Washington, D. C. R. W. Kern, Verde, Ariz. J. Wertheimer, Cleveland, Ohio. H. D..Kinney, Easton, Pa. C. R. Wilfley, Ouray, Colo. E. L. Lasier, Washington, D. C. J. P. Wood, Engrs., U. S. A. Carl Zapffe, Brainerd, Minn. Leland D. Adams has left the employ of the Weedon Mining Co., Ltd., at Montreal, Quebec, and is going to Oakland, Calif., where his address will be 1180 Mandana Boulevard.

Jan 5, 1919

By Eugene McAuliffe

The term "mechanical mining" carries an ambiguity which justifies a preliminary word of explanation. . All mining activity conducted in this day is more or less mechanical; that is to say, power expressed in the form of electricity, steam or compressed air is used in some portion of practically every mining activity of consequence. "Mechanical loading" is more nearly correct than "mechanical mining" in reference to present practice. The first substantial effort made in the direction of mechanical mining, subsequent to the application of steam for hoisting and underground pumping purposes, was that of substituting for hand labor undercutting and shearing by power-driven machines. The undercutting of coal by hand represented at one time the most arduous task confronting the miner. Occupying a kneeling position in the thicker beds, or lying on his side in the thinner coal, the task was tedious and exhausting. The first attempt to substitute crude air-driven, and later electrically driven, "punchers," as the percussion type of machine was called, met with much the same opposition on the part of the workers as was expressed by workers in the other industries when any innovation, whether labor-saving or otherwise, was introduced. We should not be too critical of this attitude of mind shown by the mine workers. The peculiarly isolated character of the work carried on in semidarkness by a class of men who to a large extent lived and held themselves aloof from the other branches of society led long ago to the development of a craft consciousness which they have found difficult to surrender. It was not until 1891 that a definite record of the results obtained by the use of undercutting machines of all types was made available, the quantity undercut in that year totaling 6,211,732 tons of bituminous coal from all American mines. The volume of bituminous coal undercut by machines in 1928 totaled 369,687,007 tons, or 73.8 per cent. of the nation's production. In the light of this experience, we can properly feel that the work of introducing the coal-loading machine as a substitute for hand shoveling is making substantial progress.

Jan 1, 1931

By Robert Mehl

IN examining the progress of metallurgical science, the critic must remember that most of our present knowledge of metals and alloys has been accumulated through the needs of industry and commerce rather than through the desire and efforts of a large body of scientists interested primarily in developing a science of metals. The progress of metallurgy, scientifically speaking, has been irregular, and little given to the exhaus-tive exploitation of important scientific fields. The experienced engineer now recognizes the need for the development of the basic science upon which his engineering rests. In addition to the increase in knowledge which results from the normal requirements of industry, a development of the basic science of the behavior of metals and alloys is as desirable in metallurgy as in any other branch of science and engineering. The continued growth of the science of metals-as of every other science-requires studious attention to the principles that underlie the behavior of matter, with the result that knowledge in the several fields of interest should continue to increase. Among the various subjects recognized as important in physical metallurgy few have a wider significance than that of diffusion in solid metals. The phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this, the process of diffu-sion is of first importance practically. The formation of alloys by the annealing of mixed powders, first practiced by Faraday and Stodart81 in 1820 and in more recent years investigated by Masing187,189 and others, has led to the development of special alloys like Carboloy, Vascoloy-Ramet, Genelite, Elcon68, and has recently been applied to the production of noble-metal alloys for electrical contacts"'.

Jan 1, 1936

By Lloyd Emory

THE region known as. Guyana or Guiana stretches along the north coast of South America from the mouth of the Orinoco River in Venezuela to the mouth of the Amazon River in Brazil. Politically, it is divided into British, Dutch, and French Guiana, extend¬ ing into Venezuela on the north and into Brazil on the south. Because the area is within the sweep of the northeast trade winds and of approximately the same latitude, plant' and animal life are fairly uniform throughout. The geology is very similar as far as the northern coast is concerned. The drainage is taken care of by a number of large rivers that flow northward directly into the sea. The Courantyne River, which roughly divides the area into half, is the eastern boundary of British Guiana.1 The lower reaches of this river are also the center axis of an ancient bay that at one time indented the coast-line at this point. The old shore-line and, in fact, successive shore-lines can be traced from near the present coast-line in, the northwest district of British-Guiana, south-east and inland, crossing the Essequibo River near Dahli, the Demerara near Christianburg, the Berbice at the mouth of the Kuruduni River and the Courantyne at Vaka-Kuyaha Falls. The line then swings around to the northeast and again approaches the coast near St. Lau-rent in French Guiana. This article will be confined to British Guiana and largely to the valley of the Demerara River, but for geographic names .and topographic details it might, however, apply to Dutch Guiana as well. British Guiana, which comprises about 90,000 sq. mi. and is as large as England, Scotland, and Wales combined, may be divided into three belts, the alluvial belt or coastal plain, the foot-hill area (often spoken of as the sand clay belt), and the hinterland.

Jan 1, 1928

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, .went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the blast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success ,is made of wrought-iron tubes, 2 1/2 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglomerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Jan 1, 1873

By C. M. Nickerson

IT is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has. been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in -means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some beneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable. gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields.

Jan 1, 1929

PORPHYRY mining in the Bisbee district in Arizona did not begin until 1923, though Bisbee had been the scene of profitable copper-mining operations since 1880, and during the interval had contributed roughly 2,000,000,000 lb. of copper to the world's supply. At that time it ranked third among the copper districts of the United States, first place for total production going to Butte, Montana, and second to the district centering around Calumet, Michigan. Bisbee's production had come from the so-called "limestone" mines operated principally by the Phelps Dodge Corporation and the Calumet & Arizona Mining Co. Each of these companies had a large smelting plant at Douglas, 25 miles southeast of Bisbee on the Mexican border. The town of Douglas owed its existence primarily to the copper mines of Bisbee, the particular location having been determined, first, by the fact that water in adequate supply could be obtained by sinking wells; and, second, by its position about equally distant from Bisbee and the mines in Sonora, Mexico, of the Moctezuma Copper Co., a Phelps Dodge subsidiary. Three partners, Martin, Reilly, and Ballard, conducted the first operations of consequence at Bisbee about 1880; and in 1881 a smelting plant consisting of two 36 in. water-jacketed blast furnaces was erected near by. The ore came from open-cut workings on the later-to-be-famous Queen orebody. The furnace charge is said to have averaged 23 per cent copper-twice as rich as the concentrates from the mills and four times as rich as the smelting ore shipped from Bisbee in recent years. As early as 1881, disputes arose among owners of various claims, and groups of claims, over the ownership of orebodies under the law of apex and extra-lateral rights. This law gives a miner the right to follow his vein downward on its dip, even

Jan 1, 1933

By R. K. Datta

Eluropium -activated yttrium vanadate, excited by short- and long-wavelength ultraviolet radiations, shows enzission lines near 6100A, the principal ones correspondirzg to transitions of EU+3 ions from 5Do to the F2 energy level. The ~neclmlallistns of absorption and etnissiorz of this phosphor have been empirically studied. The absorption is caused by two separate processes in the matrix. The phosphor YVO4:Eu and tlie matrix YVO, haue essentially the same resectance spectra in the region 2500 to 4000if. There are two broat ah~o?~ption bands: natnely, around 2600 and 3600A regions. Whet? compared with the reflectance spectra of the constituent oxides, namely, Y2O3, V205, Eu2 03, the absorption bands of the tnatvix and the phosphor in the short- and long-wavelength ultraviolet regions can be interpreted as due to charge-transfer processes involving i) Y-O and ii) 17-0, respecti~~ely. The excitation spectrum' of the phosphor has two broad bands with peaks at about 2600 and 3600A regions. U can be postulated that enevgy absorbed under short- crud long-wavelength ultraziolet excitatzon, respectzcely, by Y-0 and V-O parts of the niatrix is transferred by radcatio~zless process to EU+3 ions. Thzs postulate can empirically be proved on the basis of the spectra of the systems (YVO4,-YPO4,):Eu. PO? ~ons do not have' any appreciable absorption in the short or long uv regions. When P0't3 ions are substitlited for v0i3 ions in YVO,:Eu phosphors, the absorption and excitation in the lo~zg uv region are gradually reduced. Ailoreover, the £«+3 emission under 3650A excitation is decreased zuitlz increase in PO^ content, lt~lzereas the emission under 253711 excitation remains esserztially constant with as IILUCIL as 60 mole pct of YPO, in YVO,:En. EUROPIUM-activated yttrium vanadate (YV04:Eu) is a well-known phosptor.'-3 When excited by cathode rays, 2537, or 3650A radiations, YV04:Eu emits typical narrow-band spectrum of EU'3 fluorescence in the region of 5900 to 7100A, a very strong maximum occurring at about 6190A. This emission is considered to be due to 5Do — 7F2 transition of excite: EU*3 in 4f state. Moreover, the emission under 3650A excitation increases with temperature markedly. Because of these properties, YV04:Eu phosphor finds wide application in industries, namely, in color television tube, laser, and high-pressure mercury-vapor lamps. It is the purpose of this paper 1) to present the empirical study of the mechanism of absorption and excitation of YV04:Eu phosphor by ultraviolet radiation, and 2) to offer an explanation for the process of emission. It should be mentioned that a theoretical discussion on the mechanism of absorption in terms of the crystal or ligand field theory is beyond the scope of this paper. Empirical studies presented here are based primarily on spectroscopic and crystal-chemical investigations. EXPERIMENTAL i) Preparation of Materials. The synthesis of vanadate phosphorinvolves preparation of (Yi-.tEuj^Oj, blending the mixed oxide with an oxidic compound of vanadium, such as V205 or NH4V03, and firing the mixture at about 1000°C for several hours when YVO4:Eu forms as a primary phase. (Y1-xEux)203 compositions are prepared by coprecipitation of oxalates, and igniting them at about 1000°C. The vanadium compound is added in excess of the stoichiometric proportion for fluxing purposes. The charge is cooled, ground, and the excess of vanadium is removed by a hot wash (-80°C) of alkali or ammonia. Y(VP)04:Eu samples are prepared by mixing (Yi-xEux)203 with stoichio-metric proportions of (NH4)2HP04 and the vanadium compound. The mixtures are prefired at 700" to 800°C for 1 or 2 hr, then ground and refired at 1150°C. The firings of the phosphors are done in silica crucibles, and the homogeneity of the final products checked by X-ray diffraction analysis. ii) Spectroscopic Measurements. Diffuse reflectance sqectra of the samples within the range 2500 to 7000A are obtained by using CaF2 as standard in Cary Recording Spectrophotometer, Model No. 14. The emission spectra from phosphor plaques, excited under different ultraviolet sources, are obtained by a direct-recording spectroradiometer4 adapted with a grating monochromator with nearly constant dispersion. Maximym sensitivity in the spectral region from 2500 to 7000A is obtained with a quartz-windowed, S-20 response p$otomultiplier. The total' band pass is kept about 30A. The spectra are calibrated against the light from a standard tungsten filament lamp reflected from a magnesium-oxide plaque. Brightness data given throughout this report $re measured from the height of the main peak (6190A) of the emission spectra. The excitation spectra are measured using sodium salicy-late as standard. RESULTS AND DISCUSSION The diffuse reflectance spectra of both pure and activated YV04, along with their constituent components, are shown in Fig. 1. YVO4 shows two broad absorption bands, namely, around 2500 and 3600A, respectively. Since there is little difference between the reflectance spectraoof YVO4 and YVO,:Eu in the uv region (2500 to 4000A), it can be postulated that excitation of the phosphor is mainly due to absorption by the matrix, i.e., YVO4. The question, now, is whether the matrix (Yv04) is excited as a whole, or different components are responsible for the two absorption bands. The characteristic absorption spectra of molecular ions involving transition metal ions, both in aqueous solutions and in crystals, are due to electronic transi-

Jan 1, 1968