Search Documents

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

By Vaughan R. Voller

"Over the last ten years an increasing number of heat and mass transfer models of solidification processes have been presented in the literature. A key component in these models is the coupling between thermal and solute fields. This is achieved by developing relationships based on the behavior at the microscopic scale in the casting (typically a secondary dendrite arm space). An important class of models in this respect are models that describe the local scale redistribution of solute alloy components-collectively referred to as microsegregation models. This paper explores this class of models.IntroductionModeling takes a key role in processing materials for properties. This is particularly time in solidification processes where current computer techniques allow for a detailed treatment of the critical macroscopic phenomena. Typically these macro scale models consist ·of three main coupled components.1. A model of flow in the melt and solid + liquid mushy region.2. A model of heat transfer.3. A model of solute transport.The focus of this paper is the solute transport component, in particular the manner in which process scale transport is coupled to transport ·at the local scale of the solid-liquid interface. This step requires a modeling of the redistribution of solutes at the scale of the secondary arm spaces in the dendritic mushy region-a process referred to as microsegregation. Basic microsegregation models use the limit assumptions of no mass diffusion in the solid (Gulliver-Scheil [l]) or complete diffusion in the solid (equilibrium lever rule) in a fixed and space. Recently, however, more sophisticated microsegregation models that account for finite mass diffusion and coarsening of the arm space have been developed [2-19]. In this paper governing equations for a general microsegregation model for a multi-component alloy in a coarsening and spacing _are introduced. From these general equations various models for a binary system are developed and tested"

Jan 1, 2000

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette's core. The measurement of the carbon content on the globules and the external iron layer is also presented.

Jan 1, 2003

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette's core. The measurement of the carbon content on the globules and the external iron layer is also presented

Jan 1, 2003

By William Petruk

Many gold operations lose gold during processing because some ore characteristics which affect recoveries have not been determined, and consequently the plant could not be designed to account for them. The ore characteristics can be determined with mineralogical techniques by analyzing the plant feed, final tailings and mill products. The plant feed and/or final tailings are commonly analyzed first as a separate project. Mill products are analyzed only if the process employs a minerals separation circuit to produce a concentrate (e.g. secondary flotation circuit to concentrate gold-bearing arsenopyrite), and if assays and materials balances indicate a recovery problem in the minerals separation circuit. Many ores have been evaluated at CANMET on a confidential cost-recovery basis by custom-designing a work plan which was dependent upon the problem and on the characteristics of the ore. The reasons for gold losses have been identified in most cases, and suggestions for modifying flowsheets have been proposed. The methods used in performing the analyses are described in this paper, and non-confidential results from in-house projects are provided as examples of the benefits of such analyses. The analytical methodology involves a combination of the following procedures: -producing heavy mineral concentrates and identifying the gold minerals in the concentrates; -determining quantities of invisible gold in gold-bearing sulphides, sulpharsenides, etc. by SIMS; -determining quantities and liberation characteristics of all gold minerals and gold-bearing minerals in the sample; -finding and identifying gold minerals in silicates; -extensive grinding and cyanidation to determine the ultimate amount of cyanidable gold; -determining impact of clay minerals and graphite; -performing a mineral balance for the gold in each sample; -performing a materials balance to determine the distribution of the gold minerals, gold-bearing minerals, and other minerals throughout the flowsheet, and; -interpreting the results.

Jan 1, 1995

By John R. Turney

The success of the Mclaughlin acid pressure oxidatiun process has proved that a complex hydrometallurgical process can be an economically viable means of treating refractory gold ores. Homestake's Mclaughin acid pressure oxidation process was commissioned in August 1985 and ts currently operating at design tonnage of 3,000 tons per day. Mineralogical and process studies on the operating plant are discussed to show the improved understanding: of the process and its future applications. These studies are also compared with the initial process development work, thus illustrating the success of the initial scale up considerations.

Jan 1, 1989

By A. Kontopoulos

The extraction of nickel and cobalt from low-grade greek laterites by sulfuric acid leaching has been studied. Batch and continuous mini-plant atmospheric leaching as well as pressure leaching techniques were employed. Atmospheric leaching at temperatures as high as 95 OC generally resulted in low Ni extractions (up to 82%), high acid consumption (650-850 kg/t ore or 80-100 kg/kg Ni) and high Fe co-dissolution (30%). Pressure leaching at 260 OC increased Ni extraction to over 98%, with minimal Fe co-dissolution (2.5%); acid consumption was 300 kg/t ore (31 kg/kg Ni). Detailed experimental results and conceptual flow sheets for atmospheric and pressure leaching are presented.

Jan 1, 1991

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By K. Krishnapisharody, G. A. Irons

"The modeling of gas-liquid plumes in steelmaking ladles has been the subject of many investigations. In most studies, the “modified” Froude number, based on the momentum of the injected gas, has been employed to characterize two-phase plumes. This approach has several shortcomings and is critically reviewed in the present work. Based on an extensive review of previous work and theoretical considerations, it is demonstrated that the injected momentum and consequently, the modified Froude number has no significance to gas blowing operations in Ladle Metallurgy. Instead, an approach based on the “plume” Froude number, previously shown by the authors as the proper form for Froude similarity, is extended as a simpler alternative.IntroductionGas injection is central to most Ladle Metallurgy operations. During ladle processing, the steel melt is usually stirred by an inert gas like Argon through porous plug(s) fitted in the bottom of the ladle or a lance inserted deep into the melt. The purging serves several purposes viz., homogenizing the melt, flotation of inclusions, enhancing the rates both of refining reactions and dissolution of alloying elements and promoting inter-phase interactions in the ladle.The topic of gas injection into liquid baths has been the subject of several investigations in the past. A great deal of this work, both experimental and computational, was devoted to describing the structure and properties of two-phase plumes as reviewed recently [1]. Generally, the ascending two-phase mixture is sub-divided into three distinct regions [2]: the jet core, transition and the bubble plume, respectively. The jet region, where the momentum of the injected gas is transferred to the bulk liquid, is also called the ‘momentum region’. In a similar manner, the plume is called the ‘buoyancy region’ where the motion of liquid is caused by the buoyancy force exerted by the bubbles. The proper characterization of these regions is important for the analysis and modeling of stirring operations in Ladle Metallurgy. Although many mathematical correlations exist for this purpose, some issues of theoretical and practical interest to the modeling of gas-liquid plumes need further attention."

Jan 1, 2012

By Chen-Ming Kuo, Esher Hsu

"The importers and manufacturers who import or produce products with packaging containers are charged a recycling fee in Taiwan. The amount of waste packaging containers used for calculating the recycling charge is based upon the amount declared by importers and manufacturers which might be underestimated. This study aims to estimate the amount of waste packaging containers generated by households in Taiwan and also explores its distribution. The sampling survey and ratio estimation are conducted for estimating the recycled amount; while the refuse sampling method for municipal solid waste composition is employed to estimate the un-recycled waste packaging containers. The estimated total amount of waste packaging containers in 2011 generated by households in Taiwan is 696,511 m.t., of which, 79.49% of the waste packaging containers were recycled and 20.51 % were landfilled or incinerated. This study shows that the amount of waste packaging containers declared by importers and producers is underestimated around 20%.IntroductionWaste packaging containers including iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs are officially announced to be recycled in Taiwan. In order to create the economic incentive for raising recycling performance, associated manufacturers and importers are charged a recycling fee to subsidize recyclers. The amount of packaging containers declared by importers and manufacturers is used for calculating the recycling charge and recycling rate. The importers and manufacturers might underreport their producing (importing) amount to pay less recycling fees. Therefore, the estimated waste packaging containers based upon the amount declared by importers and manufacturers is usually underestimated. Related previous studies about waste packaging containers recycling in Taiwan are done by Hsu and co-workers [1-4]. Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values. Hsu and Liu [5] provided a cost analysis of recycling for waste packaging containers in Taiwan. Bor, Chien, and Hsu [2] presented a market-incentive recycling system for waste packaging containers in Taiwan. Hsu and Kuo [4] provided an amending mechanism for product charge and recycling subsidy in response to the social economic changes for waste packaging containers recycling. Lee and Hsu [ 6, 7] explored the distribution, fee rates, and collection rate of waste containers. This study aims to estimate the amount of waste packaging containers generated by households in Taiwan and also explore its distribution."

Jan 1, 2014

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal&apos; prOduced&apos;and the distribution of copper in these phases as a function? of the concentrate &apos;(calcine) analysis.

Jan 1, 1983